[U-Boot] [PATCH V2] spi: mxs: Configure chipselect after block reset

[Marek Vasut <marex@denx.de>]

Dear Stefano Babic,

> On 26/08/2013 17:45, Marek Vasut wrote:
> > The chipselect must be written into the CTRL0 register after the SSP
> > block is reset, otherwise the block will always use ChipSelect #0.
> > 
> > Signed-off-by: Marek Vasut <marex@denx.de>
> > Cc: Fabio Estevam <fabio.estevam@freescale.com>
> > Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
> > Cc: Otavio Salvador <otavio@ossystems.com.br>
> > Cc: Stefano Babic <sbabic@denx.de>
> > ---
> > 
> >  drivers/spi/mxs_spi.c |   12 +++---------
> >  1 file changed, 3 insertions(+), 9 deletions(-)
> > 
> > V2: Clean up a warning that "ssp_regs" are not used
> > 
> > diff --git a/drivers/spi/mxs_spi.c b/drivers/spi/mxs_spi.c
> > index 3cf7142..2b9f395 100644
> > --- a/drivers/spi/mxs_spi.c
> > +++ b/drivers/spi/mxs_spi.c
> > @@ -56,8 +56,6 @@ struct spi_slave *spi_setup_slave(unsigned int bus,
> > unsigned int cs,
> > 
> >  				  unsigned int max_hz, unsigned int mode)
> >  
> >  {
> >  
> >  	struct mxs_spi_slave *mxs_slave;
> > 
> > -	struct mxs_ssp_regs *ssp_regs;
> > -	int reg;
> > 
> >  	if (!spi_cs_is_valid(bus, cs)) {
> >  	
> >  		printf("mxs_spi: invalid bus %d / chip select %d\n", bus, cs);
> > 
> > @@ -74,13 +72,7 @@ struct spi_slave *spi_setup_slave(unsigned int bus,
> > unsigned int cs,
> > 
> >  	mxs_slave->max_khz = max_hz / 1000;
> >  	mxs_slave->mode = mode;
> >  	mxs_slave->regs = mxs_ssp_regs_by_bus(bus);
> > 
> > -	ssp_regs = mxs_slave->regs;
> > 
> > -	reg = readl(&ssp_regs->hw_ssp_ctrl0);
> > -	reg &= ~(MXS_SSP_CHIPSELECT_MASK);
> > -	reg |= cs << MXS_SSP_CHIPSELECT_SHIFT;
> > -
> > -	writel(reg, &ssp_regs->hw_ssp_ctrl0);
> > 
> >  	return &mxs_slave->slave;
> >  
> >  err_init:
> > @@ -102,7 +94,9 @@ int spi_claim_bus(struct spi_slave *slave)
> > 
> >  	mxs_reset_block(&ssp_regs->hw_ssp_ctrl0_reg);
> > 
> > -	writel(SSP_CTRL0_BUS_WIDTH_ONE_BIT, &ssp_regs->hw_ssp_ctrl0);
> > +	writel((slave->cs << MXS_SSP_CHIPSELECT_SHIFT) |
> > +	       SSP_CTRL0_BUS_WIDTH_ONE_BIT,
> > +	       &ssp_regs->hw_ssp_ctrl0);
> > 
> >  	reg = SSP_CTRL1_SSP_MODE_SPI | SSP_CTRL1_WORD_LENGTH_EIGHT_BITS;
> >  	reg |= (mxs_slave->mode & SPI_CPOL) ? SSP_CTRL1_POLARITY : 0;
> 
> Acked-by: Stefano Babic <sbabic@denx.de>

Can we push this via IMX tree ?

Best regards,
Marek Vasut