[U-Boot] [PATCH V2] spi: mxs: Configure chipselect after block reset

[Marek Vasut <marex@denx.de>]

Dear Jagan Teki,

> Hi
> 
> On Tue, Aug 27, 2013 at 2:51 PM, Marek Vasut <marex@denx.de> wrote:
> > Dear Jagan Teki,
> > 
> >> Hi,
> >> 
> >> On Tue, Aug 27, 2013 at 2:35 PM, Marek Vasut <marex@denx.de> wrote:
> >> > Dear Stefano Babic,
> >> > 
> >> >> On 26/08/2013 17:45, Marek Vasut wrote:
> >> >> > The chipselect must be written into the CTRL0 register after the
> >> >> > SSP block is reset, otherwise the block will always use ChipSelect
> >> >> > #0.
> >> >> > 
> >> >> > Signed-off-by: Marek Vasut <marex@denx.de>
> >> >> > Cc: Fabio Estevam <fabio.estevam@freescale.com>
> >> >> > Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
> >> >> > Cc: Otavio Salvador <otavio@ossystems.com.br>
> >> >> > Cc: Stefano Babic <sbabic@denx.de>
> >> >> > ---
> >> >> > 
> >> >> >  drivers/spi/mxs_spi.c |   12 +++---------
> >> >> >  1 file changed, 3 insertions(+), 9 deletions(-)
> >> >> > 
> >> >> > V2: Clean up a warning that "ssp_regs" are not used
> >> >> > 
> >> >> > diff --git a/drivers/spi/mxs_spi.c b/drivers/spi/mxs_spi.c
> >> >> > index 3cf7142..2b9f395 100644
> >> >> > --- a/drivers/spi/mxs_spi.c
> >> >> > +++ b/drivers/spi/mxs_spi.c
> >> >> > @@ -56,8 +56,6 @@ struct spi_slave *spi_setup_slave(unsigned int
> >> >> > bus, unsigned int cs,
> >> >> > 
> >> >> >                               unsigned int max_hz, unsigned int
> >> >> >                               mode)
> >> >> >  
> >> >> >  {
> >> >> >  
> >> >> >     struct mxs_spi_slave *mxs_slave;
> >> >> > 
> >> >> > -   struct mxs_ssp_regs *ssp_regs;
> >> >> > -   int reg;
> >> >> > 
> >> >> >     if (!spi_cs_is_valid(bus, cs)) {
> >> >> >     
> >> >> >             printf("mxs_spi: invalid bus %d / chip select %d\n",
> >> >> >             bus, cs);
> >> >> > 
> >> >> > @@ -74,13 +72,7 @@ struct spi_slave *spi_setup_slave(unsigned int
> >> >> > bus, unsigned int cs,
> >> >> > 
> >> >> >     mxs_slave->max_khz = max_hz / 1000;
> >> >> >     mxs_slave->mode = mode;
> >> >> >     mxs_slave->regs = mxs_ssp_regs_by_bus(bus);
> >> >> > 
> >> >> > -   ssp_regs = mxs_slave->regs;
> >> >> > 
> >> >> > -   reg = readl(&ssp_regs->hw_ssp_ctrl0);
> >> >> > -   reg &= ~(MXS_SSP_CHIPSELECT_MASK);
> >> >> > -   reg |= cs << MXS_SSP_CHIPSELECT_SHIFT;
> >> >> > -
> >> >> > -   writel(reg, &ssp_regs->hw_ssp_ctrl0);
> >> >> > 
> >> >> >     return &mxs_slave->slave;
> >> >> >  
> >> >> >  err_init:
> >> >> > @@ -102,7 +94,9 @@ int spi_claim_bus(struct spi_slave *slave)
> >> >> > 
> >> >> >     mxs_reset_block(&ssp_regs->hw_ssp_ctrl0_reg);
> >> >> > 
> >> >> > -   writel(SSP_CTRL0_BUS_WIDTH_ONE_BIT, &ssp_regs->hw_ssp_ctrl0);
> >> >> > +   writel((slave->cs << MXS_SSP_CHIPSELECT_SHIFT) |
> >> >> > +          SSP_CTRL0_BUS_WIDTH_ONE_BIT,
> >> >> > +          &ssp_regs->hw_ssp_ctrl0);
> >> >> > 
> >> >> >     reg = SSP_CTRL1_SSP_MODE_SPI |
> >> >> >     SSP_CTRL1_WORD_LENGTH_EIGHT_BITS; reg |= (mxs_slave->mode &
> >> >> >     SPI_CPOL) ? SSP_CTRL1_POLARITY : 0;
> >> >> 
> >> >> Acked-by: Stefano Babic <sbabic@denx.de>
> >> > 
> >> > Can we push this via IMX tree ?
> >> 
> >> I have a simple concern about commit head msg.
> >> spi: mxs:
> >> spi: mxs_spi:
> >> 
> >> I preferred the second one as rest are follow the same, just for
> >> unification. Please send the v2, if your OK. then I will push it on my
> >> tree.
> > 
> > Can you fix that before pushing? I am fine either way.
> 
> OK, sure I will do that.

Thanks a lot!

Best regards,
Marek Vasut