[U-Boot] [PATCH] arm: trats: add the sd-card power control function.

[Lukasz Majewski <l.majewski@samsung.com>]

Hi Jaehoon,

> To use the sd-card, VTF_2.8V will be enabled.
> Before this patch, VTF_2.8V is always disabled.(card can't
> initialize.) When card is detected, SD-card power will enable with
> sd_ldo_control().
> 
> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
> ---
>  board/samsung/trats/trats.c |   38
> ++++++++++++++++++++++++++++++++------ 1 file changed, 32
> insertions(+), 6 deletions(-)
> 
> diff --git a/board/samsung/trats/trats.c b/board/samsung/trats/trats.c
> index 7f61d17..9b6dd12 100644
> --- a/board/samsung/trats/trats.c
> +++ b/board/samsung/trats/trats.c
> @@ -408,11 +408,31 @@ int checkboard(void)
>  #endif
>  
>  #ifdef CONFIG_GENERIC_MMC
> +static int sd_ldo_control(int on)
> +{
> +	struct pmic *p = pmic_get("MAX8997_PMIC");
> +	u32 val = 0;
> +	int ret = 0;
> +	if (pmic_probe(p))
> +		return -1;

Maybe -1 -> -ENODEV

> +
> +	/* LDO17 VTF: 2.8V */
> +	val = max8997_reg_ldo(2800000) | (on? EN_LDO : DIS_LDO);
                                          ^^^ on ?
> +	ret |= pmic_reg_write(p, MAX8997_REG_LDO17CTRL, val);
	^^^^^ ret = 
> +
> +	if (ret) {
> +		puts("MAX8997 SD setting error!\n");
		
Please use error() instead of puts()

> +		return -1;
> +	}
> +
> +	return 0;
> +}
> +
>  int board_mmc_init(bd_t *bis)
>  {
>  	struct exynos4_gpio_part2 *gpio =
>  		(struct exynos4_gpio_part2
> *)samsung_get_base_gpio_part2();
> -	int err;
> +	int err, err_sd = 0;

I think that the err_sd is not needed here. Please use the err as is
was at the original code.

>  
>  	/* eMMC_EN: SD_0_CDn: GPK0[2] Output High */
>  	s5p_gpio_direction_output(&gpio->k0, 2, 1);
> @@ -438,14 +458,20 @@ int board_mmc_init(bd_t *bis)
>  	 * GPX3[4] T-flash detect pin
>  	 */
>  	if (!s5p_gpio_get_value(&gpio->x3, 4)) {
> -		err = exynos_pinmux_config(PERIPH_ID_SDMMC2,
> PINMUX_FLAG_NONE);
> -		if (err)
> +		err_sd = exynos_pinmux_config(PERIPH_ID_SDMMC2,
> PINMUX_FLAG_NONE);
> +		if (err_sd)
>  			debug("SDMMC2 not configured\n");
> -		else
> -			err = s5p_mmc_init(2, 4);
> +		else {
> +			if (!sd_ldo_control(1)) {
> +				err_sd = s5p_mmc_init(2, 4);
> +				if (err_sd) {
> +					sd_ldo_control(0);
> +				}
				Parenthesis with this if aren't needed.
> +			}
> +		}
>  	}
>  
> -	return err;
> +	return err & err_sd;
>  }
>  #endif
>  



-- 
Best regards,

Lukasz Majewski

Samsung R&D Institute Poland (SRPOL) | Linux Platform Group