[U-Boot] [PATCH 0/5] ARM: Allwinner sun7i (A20) USB Host EHCI support

[U-Boot] [PATCH 0/5] ARM: Allwinner sun7i (A20) USB Host EHCI support

[Roman Byshko]

This patch series adds USB Host EHCI support to the sun7i SoC. It was
tested on Cubietruck. Now you could boot from a USB stick or use a
compatible Ethernet dongle to add a second Ethernet port in U-Boot.

ehci-sunxi.c contains some code for poking GPIOs. This code will go
away once some other patches for sunXi SoCs are applied against upstream.
For now this patch series is self-contained and has no dependencies.

Best,
Roman Byshko

Roman Byshko (5):
  sunxi: add defines to control USB Host clocks/resets
  sunxi: add USB EHCI driver
  sunxi: add USB options to configs
  sun7i: add USB EHCI configuration
  sun7i: cubietruck: enable USB EHCI

 arch/arm/include/asm/arch-sunxi/clock_sun4i.h |   4 +
 boards.cfg                                    |   2 +-
 drivers/usb/host/Makefile                     |   1 +
 drivers/usb/host/ehci-sunxi.c                 | 236 ++++++++++++++++++++++++++
 include/configs/sun7i.h                       |   8 +
 include/configs/sunxi-common.h                |   6 +
 6 files changed, 256 insertions(+), 1 deletion(-)
 create mode 100644 drivers/usb/host/ehci-sunxi.c

-- 
2.0.0

[U-Boot] [PATCH 1/5] sunxi: add defines to control USB Host clocks/resets

[Roman Byshko]

Signed-off-by: Roman Byshko <rbyshko@gmail.com>
---
 arch/arm/include/asm/arch-sunxi/clock_sun4i.h | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/include/asm/arch-sunxi/clock_sun4i.h b/arch/arm/include/asm/arch-sunxi/clock_sun4i.h
index 928f3f2..fe7348a 100644
--- a/arch/arm/include/asm/arch-sunxi/clock_sun4i.h
+++ b/arch/arm/include/asm/arch-sunxi/clock_sun4i.h
@@ -253,4 +253,8 @@ struct sunxi_ccm_reg {
 #define CCM_GMAC_CTRL_GPIT_MII (0x0 << 2)
 #define CCM_GMAC_CTRL_GPIT_RGMII (0x1 << 2)
 
+#define CCM_USB_CTRL_PHY1_RST (0x1 << 1)
+#define CCM_USB_CTRL_PHY2_RST (0x1 << 2)
+#define CCM_USB_CTRL_PHYGATE (0x1 << 8)
+
 #endif /* _SUNXI_CLOCK_SUN4I_H */
-- 
2.0.0

[U-Boot] [PATCH 2/5] sunxi: add USB EHCI driver

[Roman Byshko]

Signed-off-by: Roman Byshko <rbyshko@gmail.com>
---
 drivers/usb/host/Makefile     |   1 +
 drivers/usb/host/ehci-sunxi.c | 236 ++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 237 insertions(+)
 create mode 100644 drivers/usb/host/ehci-sunxi.c

diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index 04c1a64..c4f5157 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -35,6 +35,7 @@ obj-$(CONFIG_USB_EHCI_PPC4XX) += ehci-ppc4xx.o
 obj-$(CONFIG_USB_EHCI_MARVELL) += ehci-marvell.o
 obj-$(CONFIG_USB_EHCI_PCI) += ehci-pci.o
 obj-$(CONFIG_USB_EHCI_SPEAR) += ehci-spear.o
+obj-$(CONFIG_USB_EHCI_SUNXI) += ehci-sunxi.o
 obj-$(CONFIG_USB_EHCI_TEGRA) += ehci-tegra.o
 obj-$(CONFIG_USB_EHCI_VCT) += ehci-vct.o
 obj-$(CONFIG_USB_EHCI_RMOBILE) += ehci-rmobile.o
diff --git a/drivers/usb/host/ehci-sunxi.c b/drivers/usb/host/ehci-sunxi.c
new file mode 100644
index 0000000..5817fc7
--- /dev/null
+++ b/drivers/usb/host/ehci-sunxi.c
@@ -0,0 +1,236 @@
+/*
+ * Copyright (C) 2014 arokux
+ *
+ * arokux <arokux@gmail.com>
+ *
+ * Based on code from
+ * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/cpu.h>
+#include "ehci.h"
+
+#define BIT(x)	(1 << (x))
+
+#define SUNXI_USB1_IO_BASE		0x01c14000
+#define SUNXI_USB2_IO_BASE		0x01c1c000
+
+#define SUNXI_USB_PMU_IRQ_ENABLE	0x800
+#define SUNXI_USB_CSR			0x01c13404
+#define SUNXI_USB_PASSBY_EN		1
+
+#define SUNXI_EHCI_AHB_ICHR8_EN		BIT(10)
+#define SUNXI_EHCI_AHB_INCR4_BURST_EN	BIT(9)
+#define SUNXI_EHCI_AHB_INCRX_ALIGN_EN	BIT(8)
+#define SUNXI_EHCI_ULPI_BYPASS_EN	BIT(0)
+
+static struct sunxi_ehci_hcd {
+	void *ehci_base;
+	struct usb_hcd *hcd;
+	int usb_rst_mask;
+	int ahb_clk_mask;
+	int gpio_vbus;
+	void *csr;
+	int irq;
+	int id;
+} sunxi_echi_hcd[CONFIG_USB_MAX_CONTROLLER_COUNT] = {
+	[0] = {
+		.ehci_base = (void *) SUNXI_USB1_IO_BASE,
+		.usb_rst_mask = CCM_USB_CTRL_PHY1_RST,
+		.ahb_clk_mask = BIT(AHB_GATE_OFFSET_USB_EHCI0),
+		.gpio_vbus = CONFIG_SUNXI_USB_VBUS0_GPIO,
+		.csr = (void*) SUNXI_USB_CSR,
+		.irq = 39,
+		.id = 1,
+	},
+#if (CONFIG_USB_MAX_CONTROLLER_COUNT > 1)
+	[1] = {
+		.ehci_base = (void *) SUNXI_USB2_IO_BASE,
+		.usb_rst_mask = CCM_USB_CTRL_PHY2_RST,
+		.ahb_clk_mask = BIT(AHB_GATE_OFFSET_USB_EHCI1),
+		.gpio_vbus = CONFIG_SUNXI_USB_VBUS1_GPIO,
+		.csr = (void*) SUNXI_USB_CSR,
+		.irq = 40,
+		.id = 2,
+	}
+#endif
+};
+
+static int sunxi_gpio_output(u32 pin, u32 val)
+{
+	u32 dat;
+	u32 bank = GPIO_BANK(pin);
+	u32 num = GPIO_NUM(pin);
+	struct sunxi_gpio *pio =
+		&((struct sunxi_gpio_reg *)SUNXI_PIO_BASE)->gpio_bank[bank];
+
+	dat = readl(&pio->dat);
+	if (val)
+		dat |= 0x1 << num;
+	else
+		dat &= ~(0x1 << num);
+
+	writel(dat, &pio->dat);
+
+	return 0;
+}
+
+static void usb_phy_write(struct sunxi_ehci_hcd *sunxi_ehci, int addr,
+			  int data, int len)
+{
+	int temp = 0, j = 0, usbc_bit = 0;
+	void *dest = sunxi_ehci->csr;
+
+	usbc_bit = BIT(sunxi_ehci->id * 2);
+	for (j = 0; j < len; j++) {
+		/* set the bit address to be written */
+		temp = readl(dest);
+		temp &= ~(0xff << 8);
+		temp |= ((addr + j) << 8);
+		writel(temp, dest);
+
+		clrbits_le32(dest, usbc_bit);
+		/* set data bit */
+		if (data & 0x1)
+			temp |= BIT(7);
+		else
+			temp &= ~BIT(7);
+		writeb(temp, dest);
+
+		setbits_le32(dest, usbc_bit);
+
+		clrbits_le32( dest, usbc_bit);
+
+		data >>= 1;
+	}
+}
+
+static void sunxi_usb_phy_init(struct sunxi_ehci_hcd *sunxi_ehci)
+{
+	/* The following comments are machine
+	 * translated from Chinese, you have been warned!
+	 */
+
+	/* adjust PHY's magnitude and rate */
+	usb_phy_write(sunxi_ehci, 0x20, 0x14, 5);
+
+	/* threshold adjustment disconnect */
+	usb_phy_write(sunxi_ehci, 0x2a, 3, 2);
+
+	return;
+}
+
+static void sunxi_usb_passby(struct sunxi_ehci_hcd *sunxi_ehci, int enable)
+{
+	unsigned long reg_value = 0;
+	unsigned long bits = 0;
+	void *addr = sunxi_ehci->ehci_base + SUNXI_USB_PMU_IRQ_ENABLE;
+
+	bits = SUNXI_EHCI_AHB_ICHR8_EN |
+		SUNXI_EHCI_AHB_INCR4_BURST_EN |
+		SUNXI_EHCI_AHB_INCRX_ALIGN_EN |
+		SUNXI_EHCI_ULPI_BYPASS_EN;
+
+
+	reg_value = readl(addr);
+
+	if (enable)
+		reg_value |= bits;
+	else
+		reg_value &= ~bits;
+
+	writel(reg_value, addr);
+
+	return;
+}
+
+static void sunxi_ehci_enable(struct sunxi_ehci_hcd *sunxi_ehci)
+{
+	struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
+
+	setbits_le32(&ccm->usb_clk_cfg, sunxi_ehci->usb_rst_mask);
+	setbits_le32(&ccm->ahb_gate0, sunxi_ehci->ahb_clk_mask);
+
+	sunxi_usb_phy_init(sunxi_ehci);
+
+	sunxi_usb_passby(sunxi_ehci, SUNXI_USB_PASSBY_EN);
+
+	/* gpio_direction_output(sunxi_ehci->gpio_vbus, 1); */
+	sunxi_gpio_set_cfgpin(sunxi_ehci->gpio_vbus, SUNXI_GPIO_OUTPUT);
+	sunxi_gpio_output(sunxi_ehci->gpio_vbus, 1);
+}
+
+static void sunxi_ehci_disable(struct sunxi_ehci_hcd *sunxi_ehci)
+{
+	struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
+
+	/* gpio_direction_output(sunxi_ehci->gpio_vbus, 0); */
+	sunxi_gpio_set_cfgpin(sunxi_ehci->gpio_vbus, SUNXI_GPIO_OUTPUT);
+	sunxi_gpio_output(sunxi_ehci->gpio_vbus, 0);
+
+	sunxi_usb_passby(sunxi_ehci, !SUNXI_USB_PASSBY_EN);
+
+	clrbits_le32(&ccm->ahb_gate0, sunxi_ehci->ahb_clk_mask);
+	clrbits_le32(&ccm->usb_clk_cfg, sunxi_ehci->usb_rst_mask);
+}
+
+int ehci_hcd_init(int index, enum usb_init_type init, struct ehci_hccr **hccr,
+		struct ehci_hcor **hcor)
+{
+	struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
+	struct sunxi_ehci_hcd *sunxi_ehci = &sunxi_echi_hcd[index];
+
+	/* enable common PHY only once */
+	if (index == 0)
+		setbits_le32(&ccm->usb_clk_cfg, CCM_USB_CTRL_PHYGATE);
+
+	sunxi_ehci_enable(sunxi_ehci);
+
+	*hccr = sunxi_ehci->ehci_base;
+
+	*hcor = (struct ehci_hcor *)((uint32_t) *hccr
+				+ HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
+
+	debug("sunxi-ehci: init hccr %x and hcor %x hc_length %d\n",
+		(uint32_t)*hccr, (uint32_t)*hcor,
+		(uint32_t)HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
+
+	return 0;
+}
+
+int ehci_hcd_stop(int index)
+{
+	struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
+	struct sunxi_ehci_hcd *sunxi_ehci = &sunxi_echi_hcd[index];
+
+	sunxi_ehci_disable(sunxi_ehci);
+
+	/* disable common PHY only once, for the last hcd */
+	if (index == CONFIG_USB_MAX_CONTROLLER_COUNT - 1)
+		clrbits_le32(&ccm->usb_clk_cfg, CCM_USB_CTRL_PHYGATE);
+
+	return 0;
+}
-- 
2.0.0

[U-Boot] [PATCH 2/5] sunxi: add USB EHCI driver

[Ian Campbell]

On Tue, 2014-07-08 at 22:21 +0200, Roman Byshko wrote:
> diff --git a/drivers/usb/host/ehci-sunxi.c b/drivers/usb/host/ehci-sunxi.c
> new file mode 100644
> index 0000000..5817fc7
> --- /dev/null
> +++ b/drivers/usb/host/ehci-sunxi.c
> @@ -0,0 +1,236 @@
> +/*
> + * Copyright (C) 2014 arokux
> + *
> + * arokux <arokux@gmail.com>

The authorship info here contradicts the authorship suggested by the
commit email metadata and the S-o-b.

If arokux wrote this patch then the commit message should begin with 

        From: Arokux X <arokux@gmail.com>
        
on the first line and arokux needs to have Signed-off on the patch.

I'm not sure what u-boot policy says about pseudonyms.

> + *
> + * Based on code from
> + * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.

Please use the SPDX tag instead of the full license.

> +	dat = readl(&pio->dat);
> +	if (val)
> +		dat |= 0x1 << num;
> +	else
> +		dat &= ~(0x1 << num);
> +
> +	writel(dat, &pio->dat);

This is 
	if (val)
		setbits_le32(&pio->dat, 1<<num);
	else
		clrbits_le32(&pio->dat, 1<<num);

It seems like there are a bunch of similar constructs around the place.

> +	return 0;
> +}
> +
> +static void usb_phy_write(struct sunxi_ehci_hcd *sunxi_ehci, int addr,
> +			  int data, int len)
> +{
> +	int temp = 0, j = 0, usbc_bit = 0;
> +	void *dest = sunxi_ehci->csr;
> +
> +	usbc_bit = BIT(sunxi_ehci->id * 2);
> +	for (j = 0; j < len; j++) {
> +		/* set the bit address to be written */
> +		temp = readl(dest);
> +		temp &= ~(0xff << 8);
> +		temp |= ((addr + j) << 8);
> +		writel(temp, dest);

clrsetbits?

> +
> +		clrbits_le32(dest, usbc_bit);
> +		/* set data bit */
> +		if (data & 0x1)
> +			temp |= BIT(7);
> +		else
> +			temp &= ~BIT(7);
> +		writeb(temp, dest);

AFAICT this will clobber the clearing of usbc_bit which you just did,
since temp was read before that, is that right?

This should probably use the clr/setbits_le32 stuff and if it really is
deliberately clobbering usbc_bit I think it needs a comment.

> +
> +		setbits_le32(dest, usbc_bit);
> +
> +		clrbits_le32( dest, usbc_bit);

Extra space in this line.

> +	/* gpio_direction_output(sunxi_ehci->gpio_vbus, 1); */

???

> +static void sunxi_ehci_disable(struct sunxi_ehci_hcd *sunxi_ehci)
> +{
> +	struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
> +
> +	/* gpio_direction_output(sunxi_ehci->gpio_vbus, 0); */

???

Ian.

[U-Boot] [PATCH 3/5] sunxi: add USB options to configs

[Roman Byshko]

Signed-off-by: Roman Byshko <rbyshko@gmail.com>
---
 include/configs/sunxi-common.h | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/include/configs/sunxi-common.h b/include/configs/sunxi-common.h
index 5d72d62..c7746bb 100644
--- a/include/configs/sunxi-common.h
+++ b/include/configs/sunxi-common.h
@@ -181,6 +181,12 @@
 #define CONFIG_BOOTP_SEND_HOSTNAME
 #endif
 
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 1
+#define CONFIG_USB_STORAGE
+#endif
+
 #if !defined CONFIG_ENV_IS_IN_MMC && \
     !defined CONFIG_ENV_IS_IN_NAND && \
     !defined CONFIG_ENV_IS_IN_FAT && \
-- 
2.0.0

[U-Boot] [PATCH 4/5] sun7i: add USB EHCI configuration

[Roman Byshko]

Signed-off-by: Roman Byshko <rbyshko@gmail.com>
---
 include/configs/sun7i.h | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/include/configs/sun7i.h b/include/configs/sun7i.h
index 9b693f7..0a1d83e 100644
--- a/include/configs/sun7i.h
+++ b/include/configs/sun7i.h
@@ -16,6 +16,14 @@
 
 #define CONFIG_SYS_PROMPT		"sun7i# "
 
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_SUNXI
+
+#define CONFIG_USB_MAX_CONTROLLER_COUNT	2
+#define CONFIG_SUNXI_USB_VBUS0_GPIO	230
+#define CONFIG_SUNXI_USB_VBUS1_GPIO	227
+#endif
+
 /*
  * Include common sunxi configuration where most the settings are
  */
-- 
2.0.0

[U-Boot] [PATCH 5/5] sun7i: cubietruck: enable USB EHCI

[Roman Byshko]

Signed-off-by: Roman Byshko <rbyshko@gmail.com>
---
 boards.cfg | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/boards.cfg b/boards.cfg
index f16a0e6..e039d4c 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -377,7 +377,7 @@ Active  arm         armv7          rmobile     renesas         lager
 Active  arm         armv7          s5pc1xx     samsung         goni                s5p_goni                              -                                                                                                                                 Robert Baldyga <r.baldyga@samsung.com>
 Active  arm         armv7          s5pc1xx     samsung         smdkc100            smdkc100                              -                                                                                                                                 Minkyu Kang <mk7.kang@samsung.com>
 Active  arm         armv7          socfpga     altera          socfpga             socfpga_cyclone5                      -                                                                                                                                 -
-Active  arm         armv7          sunxi       -               sunxi               Cubietruck                            sun7i:CUBIETRUCK,SPL,SUNXI_GMAC,RGMII                                                                                             -
+Active  arm         armv7          sunxi       -               sunxi               Cubietruck                            sun7i:CUBIETRUCK,SPL,SUNXI_GMAC,RGMII,USB_EHCI                                                                                    -
 Active  arm         armv7          sunxi       -               sunxi               Cubietruck_FEL                        sun7i:CUBIETRUCK,SPL_FEL,SUNXI_GMAC,RGMII                                                                                         -
 Active  arm         armv7          u8500       st-ericsson     snowball            snowball                              -                                                                                                                                 Mathieu Poirier <mathieu.poirier@linaro.org>
 Active  arm         armv7          u8500       st-ericsson     u8500               u8500_href                            -                                                                                                                                 -
-- 
2.0.0

[U-Boot] [PATCH 0/5] ARM: Allwinner sun7i (A20) USB Host EHCI support

[Ian Campbell]

On Tue, 2014-07-08 at 22:21 +0200, Roman Byshko wrote:
> This patch series adds USB Host EHCI support to the sun7i SoC.

When you repost this please could you CC the USB custodian (Marek Vasut,
marex {AT} denx {DOT} de) for his input on the glue code.

>  It was
> tested on Cubietruck. Now you could boot from a USB stick or use a
> compatible Ethernet dongle to add a second Ethernet port in U-Boot.
> 
> ehci-sunxi.c contains some code for poking GPIOs. This code will go
> away once some other patches for sunXi SoCs are applied against upstream.
> For now this patch series is self-contained and has no dependencies.

Which specific patches are required?
http://patchwork.ozlabs.org/patch/356566/ Perhaps?

Ian.

[U-Boot] [PATCH 0/5] ARM: Allwinner sun7i (A20) USB Host EHCI support

[Roman B.]

On Sat, Jul 12, 2014 at 2:21 PM, Ian Campbell <ijc@hellion.org.uk> wrote:
> On Tue, 2014-07-08 at 22:21 +0200, Roman Byshko wrote:
>> This patch series adds USB Host EHCI support to the sun7i SoC.
>
> When you repost this please could you CC the USB custodian (Marek Vasut,
> marex {AT} denx {DOT} de) for his input on the glue code.
>
>>  It was
>> tested on Cubietruck. Now you could boot from a USB stick or use a
>> compatible Ethernet dongle to add a second Ethernet port in U-Boot.
>>
>> ehci-sunxi.c contains some code for poking GPIOs. This code will go
>> away once some other patches for sunXi SoCs are applied against upstream.
>> For now this patch series is self-contained and has no dependencies.
>
> Which specific patches are required?
> http://patchwork.ozlabs.org/patch/356566/ Perhaps?

Yes, exactly.

Roman

[U-Boot] [PATCH 0/5] ARM: Allwinner sun7i (A20) USB Host EHCI support

[Ian Campbell]

On Tue, 2014-07-15 at 22:54 +0200, Roman B. wrote:
> On Sat, Jul 12, 2014 at 2:21 PM, Ian Campbell <ijc@hellion.org.uk> wrote:
> > On Tue, 2014-07-08 at 22:21 +0200, Roman Byshko wrote:
> >> This patch series adds USB Host EHCI support to the sun7i SoC.
> >
> > When you repost this please could you CC the USB custodian (Marek Vasut,
> > marex {AT} denx {DOT} de) for his input on the glue code.

You haven't done this in v2.

Ian.

[U-Boot] [PATCH 0/5] ARM: Allwinner sun7i (A20) USB Host EHCI support

[Ian Campbell]

On Wed, 2014-07-16 at 07:42 +0100, Ian Campbell wrote:
> On Tue, 2014-07-15 at 22:54 +0200, Roman B. wrote:
> > On Sat, Jul 12, 2014 at 2:21 PM, Ian Campbell <ijc@hellion.org.uk> wrote:
> > > On Tue, 2014-07-08 at 22:21 +0200, Roman Byshko wrote:
> > >> This patch series adds USB Host EHCI support to the sun7i SoC.
> > >
> > > When you repost this please could you CC the USB custodian (Marek Vasut,
> > > marex {AT} denx {DOT} de) for his input on the glue code.
> 
> You haven't done this in v2.

NM, I see you followed up already to correct that mistake.

Ian.

[U-Boot] [PATCH 0/5] ARM: Allwinner sun7i (A20) USB Host EHCI support

[Marek Vasut]

On Wednesday, July 16, 2014 at 08:46:07 AM, Ian Campbell wrote:
> On Wed, 2014-07-16 at 07:42 +0100, Ian Campbell wrote:
> > On Tue, 2014-07-15 at 22:54 +0200, Roman B. wrote:
> > > On Sat, Jul 12, 2014 at 2:21 PM, Ian Campbell <ijc@hellion.org.uk> wrote:
> > > > On Tue, 2014-07-08 at 22:21 +0200, Roman Byshko wrote:
> > > >> This patch series adds USB Host EHCI support to the sun7i SoC.
> > > > 
> > > > When you repost this please could you CC the USB custodian (Marek
> > > > Vasut, marex {AT} denx {DOT} de) for his input on the glue code.
> > 
> > You haven't done this in v2.
> 
> NM, I see you followed up already to correct that mistake.

Where is the V2 ?

Best regards,
Marek Vasut

[U-Boot] [PATCH 0/5] ARM: Allwinner sun7i (A20) USB Host EHCI support

[Roman B.]

On Wed, Jul 16, 2014 at 11:20 AM, Marek Vasut <marex@denx.de> wrote:
> On Wednesday, July 16, 2014 at 08:46:07 AM, Ian Campbell wrote:
>> On Wed, 2014-07-16 at 07:42 +0100, Ian Campbell wrote:
>> > On Tue, 2014-07-15 at 22:54 +0200, Roman B. wrote:
>> > > On Sat, Jul 12, 2014 at 2:21 PM, Ian Campbell <ijc@hellion.org.uk> wrote:
>> > > > On Tue, 2014-07-08 at 22:21 +0200, Roman Byshko wrote:
>> > > >> This patch series adds USB Host EHCI support to the sun7i SoC.
>> > > >
>> > > > When you repost this please could you CC the USB custodian (Marek
>> > > > Vasut, marex {AT} denx {DOT} de) for his input on the glue code.
>> >
>> > You haven't done this in v2.
>>
>> NM, I see you followed up already to correct that mistake.
>
> Where is the V2 ?


It is here

http://lists.denx.de/pipermail/u-boot/2014-July/thread.html#183792

Best,
Roman