[U-Boot] [PATCH v2 1/3] mx6: imx-regs: Provide a structure for GPC registers

[U-Boot] [PATCH v2 1/3] mx6: imx-regs: Provide a structure for GPC registers

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@freescale.com>

Introduce a structure for accessing the General Power Controller block (GPC)
registers.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
Changes since v1:
- None

 arch/arm/include/asm/arch-mx6/imx-regs.h | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/arch/arm/include/asm/arch-mx6/imx-regs.h b/arch/arm/include/asm/arch-mx6/imx-regs.h
index 2631beb..22614fc 100644
--- a/arch/arm/include/asm/arch-mx6/imx-regs.h
+++ b/arch/arm/include/asm/arch-mx6/imx-regs.h
@@ -419,6 +419,19 @@ struct iomuxc {
 	u32 gpr[14];
 };
 
+struct gpc {
+	u32	cntr;
+	u32	pgr;
+	u32	imr1;
+	u32	imr2;
+	u32	imr3;
+	u32	imr4;
+	u32	isr1;
+	u32	isr2;
+	u32	isr3;
+	u32	isr4;
+};
+
 #define IOMUXC_GPR2_COUNTER_RESET_VAL_OFFSET		20
 #define IOMUXC_GPR2_COUNTER_RESET_VAL_MASK		(3<<IOMUXC_GPR2_COUNTER_RESET_VAL_OFFSET)
 #define IOMUXC_GPR2_LVDS_CLK_SHIFT_OFFSET		16
-- 
1.9.1

[U-Boot] [PATCH v2 2/3] pcie_imx: Add mx6solox support

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@freescale.com>

Let PCI on mx6solox also be supported.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
Changes since v1:
- Put the definition of gpc inside CONFIG_MX6SX ifdef
- Use setbits_le32 to configure register CNTR
- Improve comments in the code

 arch/arm/cpu/armv7/mx6/clock.c        |  9 ++++++++
 arch/arm/include/asm/arch-mx6/iomux.h |  9 ++++++++
 drivers/pci/pcie_imx.c                | 40 +++++++++++++++++++++++++++++++----
 3 files changed, 54 insertions(+), 4 deletions(-)

diff --git a/arch/arm/cpu/armv7/mx6/clock.c b/arch/arm/cpu/armv7/mx6/clock.c
index abd9d61..dd628d8 100644
--- a/arch/arm/cpu/armv7/mx6/clock.c
+++ b/arch/arm/cpu/armv7/mx6/clock.c
@@ -504,10 +504,19 @@ int enable_pcie_clock(void)
 #define ANADIG_ANA_MISC1_LVDSCLK1_IBEN		(1 << 12)
 #define ANADIG_ANA_MISC1_LVDSCLK1_OBEN		(1 << 10)
 #define ANADIG_ANA_MISC1_LVDS1_CLK_SEL_MASK	0x0000001F
+#ifndef CONFIG_MX6SX
+	/* lvds_clk1 is sourced from sata ref on imx6q/dl/solo */
 	clrsetbits_le32(&anatop_regs->ana_misc1,
 			ANADIG_ANA_MISC1_LVDSCLK1_IBEN |
 			ANADIG_ANA_MISC1_LVDS1_CLK_SEL_MASK,
 			ANADIG_ANA_MISC1_LVDSCLK1_OBEN | 0xb);
+#else
+	/* lvds_clk1 is sourced from pcie ref on imx6sx */
+	clrsetbits_le32(&anatop_regs->ana_misc1,
+			ANADIG_ANA_MISC1_LVDSCLK1_IBEN |
+			ANADIG_ANA_MISC1_LVDS1_CLK_SEL_MASK,
+			ANADIG_ANA_MISC1_LVDSCLK1_OBEN | 0xa);
+#endif
 
 	/* PCIe reference clock sourced from AXI. */
 	clrbits_le32(&ccm_regs->cbcmr, MXC_CCM_CBCMR_PCIE_AXI_CLK_SEL);
diff --git a/arch/arm/include/asm/arch-mx6/iomux.h b/arch/arm/include/asm/arch-mx6/iomux.h
index 6a4a632..c86aa31 100644
--- a/arch/arm/include/asm/arch-mx6/iomux.h
+++ b/arch/arm/include/asm/arch-mx6/iomux.h
@@ -19,6 +19,12 @@
 #define IOMUXC_GPR1_TEST_POWERDOWN		(1 << 18)
 
 /*
+ * IOMUXC_GPR5 bit fields
+ */
+#define IOMUXC_GPR5_PCIE_BTNRST			(1 << 19)
+#define IOMUXC_GPR5_PCIE_PERST			(1 << 18)
+
+/*
  * IOMUXC_GPR8 bit fields
  */
 #define IOMUXC_GPR8_PCS_TX_DEEMPH_GEN1_MASK		(0x3f << 0)
@@ -35,12 +41,15 @@
 /*
  * IOMUXC_GPR12 bit fields
  */
+#define IOMUXC_GPR12_RX_EQ_2			(0x2 << 0)
+#define IOMUXC_GPR12_RX_EQ_MASK			(0x7 << 0)
 #define IOMUXC_GPR12_LOS_LEVEL_9		(0x9 << 4)
 #define IOMUXC_GPR12_LOS_LEVEL_MASK		(0x1f << 4)
 #define IOMUXC_GPR12_APPS_LTSSM_ENABLE		(1 << 10)
 #define IOMUXC_GPR12_DEVICE_TYPE_EP		(0x0 << 12)
 #define IOMUXC_GPR12_DEVICE_TYPE_RC		(0x4 << 12)
 #define IOMUXC_GPR12_DEVICE_TYPE_MASK		(0xf << 12)
+#define IOMUXC_GPR12_TEST_POWERDOWN		(1 << 30)
 
 /*
  * IOMUXC_GPR13 bit fields
diff --git a/drivers/pci/pcie_imx.c b/drivers/pci/pcie_imx.c
index a3982c4..194da2e 100644
--- a/drivers/pci/pcie_imx.c
+++ b/drivers/pci/pcie_imx.c
@@ -23,13 +23,20 @@
 #define PCI_ACCESS_READ  0
 #define PCI_ACCESS_WRITE 1
 
+#ifdef CONFIG_MX6SX
+#define MX6_DBI_ADDR	0x08ffc000
+#define MX6_IO_ADDR	0x08000000
+#define MX6_MEM_ADDR	0x08100000
+#define MX6_ROOT_ADDR	0x08f00000
+#else
 #define MX6_DBI_ADDR	0x01ffc000
-#define MX6_DBI_SIZE	0x4000
 #define MX6_IO_ADDR	0x01000000
-#define MX6_IO_SIZE	0x100000
 #define MX6_MEM_ADDR	0x01100000
-#define MX6_MEM_SIZE	0xe00000
 #define MX6_ROOT_ADDR	0x01f00000
+#endif
+#define MX6_DBI_SIZE	0x4000
+#define MX6_IO_SIZE	0x100000
+#define MX6_MEM_SIZE	0xe00000
 #define MX6_ROOT_SIZE	0xfc000
 
 /* PCIe Port Logic registers (memory-mapped) */
@@ -57,6 +64,8 @@
 #define PHY_RX_OVRD_IN_LO_RX_DATA_EN (1 << 5)
 #define PHY_RX_OVRD_IN_LO_RX_PLL_EN (1 << 3)
 
+#define PCIE_PHY_PUP_REQ		(1 << 7)
+
 /* iATU registers */
 #define PCIE_ATU_VIEWPORT		0x900
 #define PCIE_ATU_REGION_INBOUND		(0x1 << 31)
@@ -421,9 +430,19 @@ static int imx_pcie_write_config(struct pci_controller *hose, pci_dev_t d,
 static int imx6_pcie_assert_core_reset(void)
 {
 	struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
-
+#if defined(CONFIG_MX6SX)
+	struct gpc *gpc_regs = (struct gpc *)GPC_BASE_ADDR;
+
+	/* SSP_EN is not used on MX6SX anymore */
+	setbits_le32(&iomuxc_regs->gpr[12], IOMUXC_GPR12_TEST_POWERDOWN);
+	/* Force PCIe PHY reset */
+	setbits_le32(&iomuxc_regs->gpr[5], IOMUXC_GPR5_PCIE_BTNRST);
+	/* Power up PCIe PHY */
+	setbits_le32(&gpc_regs->cntr, PCIE_PHY_PUP_REQ);
+#else
 	setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_TEST_POWERDOWN);
 	clrbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_REF_SSP_EN);
+#endif
 
 	return 0;
 }
@@ -441,6 +460,12 @@ static int imx6_pcie_init_phy(void)
 			IOMUXC_GPR12_LOS_LEVEL_MASK,
 			IOMUXC_GPR12_LOS_LEVEL_9);
 
+#ifdef CONFIG_MX6SX
+	clrsetbits_le32(&iomuxc_regs->gpr[12],
+			IOMUXC_GPR12_RX_EQ_MASK,
+			IOMUXC_GPR12_RX_EQ_2);
+#endif
+
 	writel((0x0 << IOMUXC_GPR8_PCS_TX_DEEMPH_GEN1_OFFSET) |
 	       (0x0 << IOMUXC_GPR8_PCS_TX_DEEMPH_GEN2_3P5DB_OFFSET) |
 	       (20 << IOMUXC_GPR8_PCS_TX_DEEMPH_GEN2_6DB_OFFSET) |
@@ -517,9 +542,16 @@ static int imx6_pcie_deassert_core_reset(void)
 	 */
 	mdelay(50);
 
+#if defined(CONFIG_MX6SX)
+	/* SSP_EN is not used on MX6SX anymore */
+	clrbits_le32(&iomuxc_regs->gpr[12], IOMUXC_GPR12_TEST_POWERDOWN);
+	/* Clear PCIe PHY reset bit */
+	clrbits_le32(&iomuxc_regs->gpr[5], IOMUXC_GPR5_PCIE_BTNRST);
+#else
 	/* Enable PCIe */
 	clrbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_TEST_POWERDOWN);
 	setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_REF_SSP_EN);
+#endif
 
 	imx6_pcie_toggle_reset();
 
-- 
1.9.1

[U-Boot] [PATCH v2 2/3] pcie_imx: Add mx6solox support

[Marek Vasut]

On Sunday, August 24, 2014 at 07:52:25 PM, Fabio Estevam wrote:

[...]

> --- a/arch/arm/cpu/armv7/mx6/clock.c
> +++ b/arch/arm/cpu/armv7/mx6/clock.c
> @@ -504,10 +504,19 @@ int enable_pcie_clock(void)
>  #define ANADIG_ANA_MISC1_LVDSCLK1_IBEN		(1 << 12)
>  #define ANADIG_ANA_MISC1_LVDSCLK1_OBEN		(1 << 10)
>  #define ANADIG_ANA_MISC1_LVDS1_CLK_SEL_MASK	0x0000001F
> +#ifndef CONFIG_MX6SX
> +	/* lvds_clk1 is sourced from sata ref on imx6q/dl/solo */
>  	clrsetbits_le32(&anatop_regs->ana_misc1,
>  			ANADIG_ANA_MISC1_LVDSCLK1_IBEN |
>  			ANADIG_ANA_MISC1_LVDS1_CLK_SEL_MASK,
>  			ANADIG_ANA_MISC1_LVDSCLK1_OBEN | 0xb);
> +#else
> +	/* lvds_clk1 is sourced from pcie ref on imx6sx */
> +	clrsetbits_le32(&anatop_regs->ana_misc1,
> +			ANADIG_ANA_MISC1_LVDSCLK1_IBEN |
> +			ANADIG_ANA_MISC1_LVDS1_CLK_SEL_MASK,
> +			ANADIG_ANA_MISC1_LVDSCLK1_OBEN | 0xa);
> +#endif

Is that only 1-bit difference here ? What does the magic 0xa and 0xb stand for 
please ?

>  	/* PCIe reference clock sourced from AXI. */
>  	clrbits_le32(&ccm_regs->cbcmr, MXC_CCM_CBCMR_PCIE_AXI_CLK_SEL);
[...]

Best regards,
Marek Vasut

[U-Boot] [PATCH v2 2/3] pcie_imx: Add mx6solox support

[Fabio Estevam]

On Mon, Aug 25, 2014 at 4:54 AM, Marek Vasut <marex@denx.de> wrote:
> On Sunday, August 24, 2014 at 07:52:25 PM, Fabio Estevam wrote:
>
> [...]
>
>> --- a/arch/arm/cpu/armv7/mx6/clock.c
>> +++ b/arch/arm/cpu/armv7/mx6/clock.c
>> @@ -504,10 +504,19 @@ int enable_pcie_clock(void)
>>  #define ANADIG_ANA_MISC1_LVDSCLK1_IBEN               (1 << 12)
>>  #define ANADIG_ANA_MISC1_LVDSCLK1_OBEN               (1 << 10)
>>  #define ANADIG_ANA_MISC1_LVDS1_CLK_SEL_MASK  0x0000001F
>> +#ifndef CONFIG_MX6SX
>> +     /* lvds_clk1 is sourced from sata ref on imx6q/dl/solo */
>>       clrsetbits_le32(&anatop_regs->ana_misc1,
>>                       ANADIG_ANA_MISC1_LVDSCLK1_IBEN |
>>                       ANADIG_ANA_MISC1_LVDS1_CLK_SEL_MASK,
>>                       ANADIG_ANA_MISC1_LVDSCLK1_OBEN | 0xb);
>> +#else
>> +     /* lvds_clk1 is sourced from pcie ref on imx6sx */
>> +     clrsetbits_le32(&anatop_regs->ana_misc1,
>> +                     ANADIG_ANA_MISC1_LVDSCLK1_IBEN |
>> +                     ANADIG_ANA_MISC1_LVDS1_CLK_SEL_MASK,
>> +                     ANADIG_ANA_MISC1_LVDSCLK1_OBEN | 0xa);
>> +#endif
>
> Is that only 1-bit difference here ? What does the magic 0xa and 0xb stand for
> please ?

Correct.

0xa means that LVDS1_CLK_SEL comes from PCIE_REF ? PCIe ref clock

0xb means that LVDS1_CLK_SEL comes from SATA_REF ? SATA ref clock

In this patch I have added comments for both cases, so hopefully it is clear.

[U-Boot] [PATCH v2 2/3] pcie_imx: Add mx6solox support

[Marek Vasut]

On Monday, August 25, 2014 at 03:54:29 PM, Fabio Estevam wrote:
> On Mon, Aug 25, 2014 at 4:54 AM, Marek Vasut <marex@denx.de> wrote:
> > On Sunday, August 24, 2014 at 07:52:25 PM, Fabio Estevam wrote:
> > 
> > [...]
> > 
> >> --- a/arch/arm/cpu/armv7/mx6/clock.c
> >> +++ b/arch/arm/cpu/armv7/mx6/clock.c
> >> @@ -504,10 +504,19 @@ int enable_pcie_clock(void)
> >> 
> >>  #define ANADIG_ANA_MISC1_LVDSCLK1_IBEN               (1 << 12)
> >>  #define ANADIG_ANA_MISC1_LVDSCLK1_OBEN               (1 << 10)
> >>  #define ANADIG_ANA_MISC1_LVDS1_CLK_SEL_MASK  0x0000001F
> >> 
> >> +#ifndef CONFIG_MX6SX
> >> +     /* lvds_clk1 is sourced from sata ref on imx6q/dl/solo */
> >> 
> >>       clrsetbits_le32(&anatop_regs->ana_misc1,
> >>       
> >>                       ANADIG_ANA_MISC1_LVDSCLK1_IBEN |
> >>                       ANADIG_ANA_MISC1_LVDS1_CLK_SEL_MASK,
> >>                       ANADIG_ANA_MISC1_LVDSCLK1_OBEN | 0xb);
> >> 
> >> +#else
> >> +     /* lvds_clk1 is sourced from pcie ref on imx6sx */
> >> +     clrsetbits_le32(&anatop_regs->ana_misc1,
> >> +                     ANADIG_ANA_MISC1_LVDSCLK1_IBEN |
> >> +                     ANADIG_ANA_MISC1_LVDS1_CLK_SEL_MASK,
> >> +                     ANADIG_ANA_MISC1_LVDSCLK1_OBEN | 0xa);
> >> +#endif
> > 
> > Is that only 1-bit difference here ? What does the magic 0xa and 0xb
> > stand for please ?
> 
> Correct.
> 
> 0xa means that LVDS1_CLK_SEL comes from PCIE_REF ? PCIe ref clock
> 
> 0xb means that LVDS1_CLK_SEL comes from SATA_REF ? SATA ref clock
> 
> In this patch I have added comments for both cases, so hopefully it is
> clear.

Can you maybe pull the mask out and just ORR it with the correct bit in the 
ifdef ? Or -- even better, can this not be done at runtime ?

Best regards,
Marek Vasut

[U-Boot] [PATCH v2 2/3] pcie_imx: Add mx6solox support

[Fabio Estevam]

On Mon, Aug 25, 2014 at 11:27 AM, Marek Vasut <marex@denx.de> wrote:

> Can you maybe pull the mask out and just ORR it with the correct bit in the
> ifdef ? Or -- even better, can this not be done at runtime ?

Yes, I implemented the run-time approach in v3. Thanks

[U-Boot] [PATCH v2 3/3] mx6sxsabresd: Add PCI support

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@freescale.com>

Tested with an Intel Wireless PCI 7260HMW card:

U-Boot 2014.10-rc1-16576-g4a8a8a8-dirty (Aug 23 2014 - 16:05:11)                
                                                                                
CPU:   Freescale i.MX6SX rev1.0 at 792 MHz                                      
Reset cause: WDOG                                                               
Board: MX6SX SABRE SDB                                                          
I2C:   ready                                                                    
DRAM:  1 GiB                                                                    
MMC:   FSL_SDHC: 0                                                              
  00:01.0     - 16c3:abcd - Bridge device                                       
   01:00.0    - 8086:08b1 - Network controller                                  

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
Changes since v1:
- None

 include/configs/mx6sxsabresd.h | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/include/configs/mx6sxsabresd.h b/include/configs/mx6sxsabresd.h
index 7967b5d..467c125 100644
--- a/include/configs/mx6sxsabresd.h
+++ b/include/configs/mx6sxsabresd.h
@@ -181,6 +181,16 @@
 #define CONFIG_POWER_PFUZE100
 #define CONFIG_POWER_PFUZE100_I2C_ADDR	0x08
 
+#define CONFIG_CMD_PCI
+#ifdef CONFIG_CMD_PCI
+#define CONFIG_PCI
+#define CONFIG_PCI_PNP
+#define CONFIG_PCI_SCAN_SHOW
+#define CONFIG_PCIE_IMX
+#define CONFIG_PCIE_IMX_PERST_GPIO	IMX_GPIO_NR(2, 1)
+#define CONFIG_PCIE_IMX_POWER_GPIO	IMX_GPIO_NR(2, 0)
+#endif
+
 /* FLASH and environment organization */
 #define CONFIG_SYS_NO_FLASH
 
-- 
1.9.1