[U-Boot] [u-boot 33/40] usb: dwc3: Makefile: Make dwc3 driver compile in u-boot

[Lukasz Majewski <l.majewski@samsung.com>]

Hi Kishon,

> Now that the entire dwc3 driver is adapted to compile with uboot
> build, modify the Makefiles so that the dwc3 driver can be built.
> 
> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
> ---
>  Makefile                        |    2 ++
>  drivers/usb/dwc3/Makefile       |   35
> +++-------------------------------- drivers/usb/gadget/udc/Makefile
> |    2 +- 3 files changed, 6 insertions(+), 33 deletions(-)
> 
> diff --git a/Makefile b/Makefile
> index 1eb6821..ca0fd76 100644
> --- a/Makefile
> +++ b/Makefile
> @@ -632,8 +632,10 @@ libs-y += drivers/spi/
>  libs-$(CONFIG_FMAN_ENET) += drivers/net/fm/
>  libs-$(CONFIG_SYS_FSL_DDR) += drivers/ddr/fsl/
>  libs-y += drivers/serial/
> +libs-y += drivers/usb/dwc3/
>  libs-y += drivers/usb/eth/
>  libs-y += drivers/usb/gadget/
> +libs-y += drivers/usb/gadget/udc/
>  libs-y += drivers/usb/host/
>  libs-y += drivers/usb/musb/
>  libs-y += drivers/usb/musb-new/
> diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile
> index afaa767..e455a52 100644
> --- a/drivers/usb/dwc3/Makefile
> +++ b/drivers/usb/dwc3/Makefile
> @@ -1,37 +1,8 @@
> -ccflags-$(CONFIG_USB_DWC3_DEBUG)	:= -DDEBUG
> -ccflags-$(CONFIG_USB_DWC3_VERBOSE)	+= -DVERBOSE_DEBUG
> -
>  obj-$(CONFIG_USB_DWC3)			+= dwc3.o
>  
> -dwc3-y					:= core.o debug.o
> -
> -ifneq ($(filter y,$(CONFIG_USB_DWC3_HOST)
> $(CONFIG_USB_DWC3_DUAL_ROLE)),)
> -	dwc3-y				+= host.o
> -endif
> -
> -ifneq ($(filter y,$(CONFIG_USB_DWC3_GADGET)
> $(CONFIG_USB_DWC3_DUAL_ROLE)),)
> -	dwc3-y				+= gadget.o ep0.o
> -endif
> -
> -ifneq ($(CONFIG_DEBUG_FS),)
> -	dwc3-y				+= debugfs.o
> -endif
> +dwc3-y					:= core.o
>  
> -##
> -# Platform-specific glue layers go here
> -#
> -# NOTICE: Make sure your glue layer doesn't depend on anything
> -# which is arch-specific and that it compiles on all situations.
> -#
> -# We want to keep this requirement in order to be able to compile
> -# the entire driver (with all its glue layers) on several
> architectures -# and make sure it compiles fine. This will also help
> with allmodconfig -# and allyesconfig builds.
> -##
> +dwc3-y					+= gadget.o ep0.o
>  
>  obj-$(CONFIG_USB_DWC3_OMAP)		+= dwc3-omap.o
> -obj-$(CONFIG_USB_DWC3_EXYNOS)		+= dwc3-exynos.o
> -obj-$(CONFIG_USB_DWC3_PCI)		+= dwc3-pci.o
> -obj-$(CONFIG_USB_DWC3_KEYSTONE)		+= dwc3-keystone.o
> -obj-$(CONFIG_USB_DWC3_QCOM)		+= dwc3-qcom.o
> -obj-$(CONFIG_USB_DWC3_ST)		+= dwc3-st.o
> +obj-$(CONFIG_USB_DWC3_PHY_OMAP)		+= ti_usb_phy.o
> diff --git a/drivers/usb/gadget/udc/Makefile
> b/drivers/usb/gadget/udc/Makefile index be265aa..12380f4 100644
> --- a/drivers/usb/gadget/udc/Makefile
> +++ b/drivers/usb/gadget/udc/Makefile
> @@ -1,4 +1,4 @@
>  #
>  # USB peripheral controller drivers
>  #
> -obj-$(CONFIG_USB_GADGET)	+= udc-core.o
> +obj-$(CONFIG_USB_DWC3_GADGET)	+= udc-core.o

Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>

-- 
Best regards,

Lukasz Majewski

Samsung R&D Institute Poland (SRPOL) | Linux Platform Group