[U-Boot] [PATCH v3 0/7] Add support for Colibri Vybrid Modules

[Marek Vasut <marex@denx.de>]

On Thursday, April 23, 2015 at 03:13:51 PM, Tom Rini wrote:
> On Thu, Apr 23, 2015 at 06:08:43PM +0530, maitysanchayan at gmail.com wrote:
> > Hello,
> > 
> > On 15-04-15 16:24:21, Sanchayan Maity wrote:
> > > Hello,
> > > 
> > > This is the third version of the patchset which adds support for the
> > > Toradex Colibri Vybrid VF50 and VF61 modules. Boot up has been tested
> > > using the serial loader over UART. Compile tested for
> > > vf610twr_defconfig and vf610twr_nand_defconfig as well.
> > > 
> > > First patch in the series refactors the DDR related code for use by
> > > both the tower board and colibri modules. It also introduces a DDR3
> > > based JEDEC timing structure.
> > > 
> > > Second third and fourth patch in this series are improvement patches
> > > related to RTC, SoC/CPU detection and caches.
> > > 
> > > Fifth patch introduces USB support for Vybrid modules. Much of the code
> > > is similar to the ehci-mx6 driver. Both host and client modes are
> > > working and DFU has also been tested with client. Currently, we
> > > restrict the ports to be in one of host and client mode.
> > > 
> > > Sixth patch adds the actual support for the Colibri modules.
> > > 
> > > Comments and feedback are most welcome. Thanks for the feedback till
> > > now.
> > > 
> > > The patchset is based and tested on the latest master branch as of
> > > this writing.
> > > 
> > > Discussion on the version 2 of the patchset can be found at the below
> > > link:
> > > https://www.mail-archive.com/u-boot at lists.denx.de/msg168727.html
> > > 
> > > Discussion on the version 1 of the patchset can be found at the below
> > > link:
> > > https://www.mail-archive.com/u-boot at lists.denx.de/msg168136.html
> > > 
> > > Changes since v2:
> > > - Rework the USB driver to use register + offset method in light of
> > > discussion which Fabio Estevam pointed out instead of the regular
> > > struct{} method which v2 used. The discussion is at the below link:
> > > https://www.marc.info/?l=u-boot&m=142609602127309&w=2
> > > 
> > > - Reorder the patchset, putting the USB support in the end and add an
> > > additional patch for adding USB support to Colibri modules. By chance
> > > if more discussions happen on the USB support, this allows picking up
> > > of atleast the first patches on which no issues have been reported so
> > > far.
> > > 
> > > - The register definitions have been moved under arch/arm/include/asm/
> > > imx-common in the regs-usbphy.h file. This was agreed on after
> > > discussion with Marek and some input from Peter Chen. Since it is not
> > > clear if SoC's other than Freescale's use the Sigmatel Phy's which seem
> > > to be use in iMX/VF/MXS, put the USH PHY register definitions in
> > > imx-common rather than include/usb in a chipidea specific file.
> > > 
> > > - Remove setting of a PLL divisor select which was added for USB but is
> > > actually not required considering default value. It also seems to break
> > > USB after my latest rebase. The file in question concerning the change
> > > is colibri_vf.c. PLL divisor selects the PLL Multiplication factor
> > > which by default is 0, setting Fout = Fref * 20 giving 480MHz. The
> > > earlier patch set this to 1 giving Fout = Fref * 22 where Fref =
> > > 24MHz.
> > > 
> > > - Rebased on the latest master branch.
> > > 
> > > Changes since v1:
> > > - Rework the USB driver to use register offsets using the regular
> > > struct {} method
> > > 
> > > - Some cleanups and fixes in the sixth patch for the colibri_vf.h file
> > > which takes care of environment variables in uboot
> > > 
> > > - Purge some useless defines in the fifth and sixth patch which were
> > > related to USB.
> > 
> > Ping!?
> > 
> > Anything preventing this patch from getting applied?
> 
> I'll pick this up soon, thanks!

This should go through u-boot-imx though ;-)