[U-Boot] [PATCH 3/4][v2]include:configs:ls1021atwr: Enable USB IP support

[Marek Vasut <marex@denx.de>]

On Thursday, April 23, 2015 at 07:03:14 PM, Ramneek Mehresh wrote:
> Enable USB IP support for both EHCI and XHCI for
> ls1021atwr platform
> 
> Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
> ---
>  include/configs/ls1021atwr.h | 36 ++++++++++++++++++++++++++++++++++++
>  include/linux/usb/xhci-fsl.h |  5 +++++
>  2 files changed, 41 insertions(+)
> 
> diff --git a/include/configs/ls1021atwr.h b/include/configs/ls1021atwr.h
> index a13876b..f208638 100644
> --- a/include/configs/ls1021atwr.h
> +++ b/include/configs/ls1021atwr.h
> @@ -28,6 +28,42 @@
>  #define CONFIG_SYS_INIT_RAM_SIZE	OCRAM_SIZE
> 
>  /*
> + * USB
> + */
> +
> +/* EHCI Support - disbaled by default as
> + * there is no signal coming out of soc on
> + * this board for this controller. However,
> + * the silicon still has this controller,
> + * and anyone can use this controller by
> + * taking signals out on their board.
> + */

Multiline comment again ;-)

> +/*#define CONFIG_HAS_FSL_DR_USB*/
> +
> +#ifdef CONFIG_HAS_FSL_DR_USB
> +#define CONFIG_USB_EHCI
> +#define CONFIG_USB_EHCI_FSL
> +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
> +#endif
> +
> +/* XHCI Support - enabled by default */
> +#define CONFIG_HAS_FSL_XHCI_USB
> +
> +#ifdef CONFIG_HAS_FSL_XHCI_USB
> +#define CONFIG_USB_XHCI_FSL
> +#define CONFIG_USB_XHCI_DWC3
> +#define CONFIG_USB_XHCI
> +#define CONFIG_USB_MAX_CONTROLLER_COUNT        1
> +#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS     2
> +#endif
> +
> +#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_XHCI_USB)
> +#define CONFIG_CMD_USB
> +#define CONFIG_USB_STORAGE
> +#define CONFIG_CMD_EXT2
> +#endif
> +
> +/*
>   * Generic Timer Definitions
>   */
>  #define GENERIC_TIMER_CLK		12500000
> diff --git a/include/linux/usb/xhci-fsl.h b/include/linux/usb/xhci-fsl.h
> index 8eaab2c..329abf7 100644
> --- a/include/linux/usb/xhci-fsl.h
> +++ b/include/linux/usb/xhci-fsl.h
> @@ -46,6 +46,11 @@
>  #define USBOTGSS_IRQ_SET_1_OEVT_EN		BIT(16)
>  #define USBOTGSS_IRQ_SET_1_DMADISABLECLR_EN	BIT(17)
> 
> +#ifdef CONFIG_LS102XA
> +#define CONFIG_SYS_FSL_XHCI_USB1_ADDR CONFIG_SYS_LS102XA_XHCI_USB1_ADDR
> +#define CONFIG_SYS_FSL_XHCI_USB2_ADDR 0

Do you need to define this _bogus_ address at all? If so, then the driver
which depends on this is broken. Why can't you just define a list of addresses
instead ? You would be able to use ARRAY_SIZE() in the driver to determine
how many controllers there are then. This is how it would look like:

#define CONFIG_FOO_BAR_ADDRS { USB1_ADDR, USB2_ADDR, ..., USBn_ADDR }

In the driver, there'd be:

<type> addrs[] = CONFIG_FOO_BAR_ADDRS;

> +#endif
> +
>  struct fsl_xhci {
>  	struct xhci_hccr *hcd;
>  	struct dwc3 *dwc3_reg;