From: Marek Vasut <marex@denx.de>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH] arm: socfpga: Add support for the Terasic DE-0 Atlas board
Date: Tue, 1 Sep 2015 10:30:38 +0200 [thread overview]
Message-ID: <201509011030.38235.marex@denx.de> (raw)
In-Reply-To: <1441083254.1867.2.camel@clsee-VirtualBox>
On Tuesday, September 01, 2015 at 06:54:14 AM, Chin Liang See wrote:
> On Mon, 2015-08-31 at 14:57 -0500, dinguyen at opensource.altera.com wrote:
> > From: Dinh Nguyen <dinguyen@opensource.altera.com>
> >
> > Add support for the Terasic DE0-Nano/Atlas-SoC Kit, which is a CycloneV
> > based board. The board can boot from SD/MMC. Ethernet is a bit different
> > because it has a KSZ9031 PHY, so for now, ethernet doesn't quite work
> > yet, as a few patches are needed to support the PHY.
> >
> > Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
> > ---
> > Hi Marek,
> >
> > This patch is based on your u-boot-socfpga/wip/boards branch.
> >
> > Thanks,
> > Dinh
> > ---
> >
> > arch/arm/dts/Makefile | 1 +
> > arch/arm/dts/socfpga_cyclone5_de0_sockit.dts | 61 +++
> > arch/arm/mach-socfpga/Kconfig | 7 +
> > board/terasic/de0/MAINTAINERS | 5 +
> > board/terasic/de0/Makefile | 9 +
> > board/terasic/de0/qts/iocsr_config.h | 658
> > +++++++++++++++++++++++++++ board/terasic/de0/qts/pinmux_config.h
> > | 220 +++++++++
> > board/terasic/de0/qts/pll_config.h | 85 ++++
> > board/terasic/de0/qts/sdram_config.h | 342 ++++++++++++++
> > board/terasic/de0/socfpga.c | 22 +
> > configs/socfpga_de0_defconfig | 21 +
> > include/configs/socfpga_de0.h | 88 ++++
> > 12 files changed, 1519 insertions(+)
> > create mode 100644 arch/arm/dts/socfpga_cyclone5_de0_sockit.dts
> > create mode 100644 board/terasic/de0/MAINTAINERS
> > create mode 100644 board/terasic/de0/Makefile
> > create mode 100644 board/terasic/de0/qts/iocsr_config.h
> > create mode 100644 board/terasic/de0/qts/pinmux_config.h
> > create mode 100644 board/terasic/de0/qts/pll_config.h
> > create mode 100644 board/terasic/de0/qts/sdram_config.h
> > create mode 100644 board/terasic/de0/socfpga.c
> > create mode 100644 configs/socfpga_de0_defconfig
> > create mode 100644 include/configs/socfpga_de0.h
> >
> > diff --git a/include/configs/socfpga_de0.h
> > b/include/configs/socfpga_de0.h new file mode 100644
> > index 0000000..47e18ba
> > --- /dev/null
> > +++ b/include/configs/socfpga_de0.h
> > @@ -0,0 +1,88 @@
> > +/*
> > + * Copyright (C) 2015 Marek Vasut <marex@denx.de>
> > + *
> > + * SPDX-License-Identifier: GPL-2.0+
> > + */
> > +#ifndef __CONFIG_TERASIC_DE0_H__
> > +#define __CONFIG_TERASIC_DE0_H__
> > +
> > +#include <asm/arch/socfpga_base_addrs.h>
> > +
> > +/* U-Boot Commands */
> > +#define CONFIG_SYS_NO_FLASH
> > +#define CONFIG_DOS_PARTITION
> > +#define CONFIG_FAT_WRITE
> > +#define CONFIG_HW_WATCHDOG
> > +
> > +#define CONFIG_CMD_ASKENV
> > +#define CONFIG_CMD_BOOTZ
> > +#define CONFIG_CMD_CACHE
> > +#define CONFIG_CMD_DFU
> > +#define CONFIG_CMD_DHCP
> > +#define CONFIG_CMD_EXT4
> > +#define CONFIG_CMD_EXT4_WRITE
> > +#define CONFIG_CMD_FAT
> > +#define CONFIG_CMD_FS_GENERIC
> > +#define CONFIG_CMD_GPIO
> > +#define CONFIG_CMD_GREPENV
> > +#define CONFIG_CMD_MII
> > +#define CONFIG_CMD_MMC
> > +#define CONFIG_CMD_PING
> > +#define CONFIG_CMD_USB
> > +#define CONFIG_CMD_USB_MASS_STORAGE
> > +
> > +/* Memory configurations */
> > +#define PHYS_SDRAM_1_SIZE 0x40000000 /* 1GiB */
> > +
> > +/* Booting Linux */
> > +#define CONFIG_BOOTDELAY 3
> > +#define CONFIG_BOOTFILE "fitImage"
>
> Wonder this should be zImage as the mmcload still using zImage?
Or maybe the mmcload should be fixed instead ; fitImage is preferred.
next prev parent reply other threads:[~2015-09-01 8:30 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-08-31 19:57 [U-Boot] [PATCH] arm: socfpga: Add support for the Terasic DE-0 Atlas board dinguyen at opensource.altera.com
2015-08-31 22:23 ` Marek Vasut
2015-09-01 4:56 ` Chin Liang See
2015-09-01 8:31 ` Marek Vasut
2015-09-01 7:38 ` Pavel Machek
2015-09-01 8:33 ` Marek Vasut
2015-09-01 15:12 ` Dinh Nguyen
2015-09-01 15:36 ` Marek Vasut
2015-09-01 21:37 ` Dinh Nguyen
2015-09-02 8:05 ` Marek Vasut
2015-09-01 15:09 ` Dinh Nguyen
2015-09-01 15:37 ` Marek Vasut
2015-09-01 4:54 ` Chin Liang See
2015-09-01 8:30 ` Marek Vasut [this message]
2015-09-01 8:45 ` Chin Liang See
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=201509011030.38235.marex@denx.de \
--to=marex@denx.de \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox