[U-Boot] [PATCH 1/4] mtd: nand: fsmc: Add BCH4 SW ECC support for SPEAr600

[Viresh Kumar <viresh.kumar@linaro.org>]

On 02-09-15, 11:10, Stefan Roese wrote:
> This patch adds support for 4-bit ECC BCH4 for the SPEAr600 SoC. This can
> be used by boards equipped with a NAND chip that requires 4-bit ECC strength.
> The SPEAr600 HW ECC only supports 1-bit ECC strength.
> 
> To enable SW BCH4, you need to specify this in your config header:
> 
> And use the command "nandecc bch4" to select this ECC scheme upon runtime.
> 
> Tested on SPEAr600 x600 board.
> 
> Signed-off-by: Stefan Roese <sr@denx.de>
> Cc: Scott Wood <scottwood@freescale.com>
> Cc: Viresh Kumar <viresh.kumar@linaro.org>
> ---
>  drivers/mtd/nand/fsmc_nand.c | 40 ++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 40 insertions(+)
> 
> diff --git a/drivers/mtd/nand/fsmc_nand.c b/drivers/mtd/nand/fsmc_nand.c
> index 567eff0..19f5526 100644
> --- a/drivers/mtd/nand/fsmc_nand.c
> +++ b/drivers/mtd/nand/fsmc_nand.c
> @@ -13,6 +13,7 @@
>  #include <asm/io.h>
>  #include <linux/bitops.h>
>  #include <linux/err.h>
> +#include <linux/mtd/nand_bch.h>
>  #include <linux/mtd/nand_ecc.h>
>  #include <linux/mtd/fsmc_nand.h>
>  #include <asm/arch/hardware.h>
> @@ -390,6 +391,45 @@ static int fsmc_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip,
>  	return 0;
>  }
>  
> +#ifndef CONFIG_SPL_BUILD
> +/*
> + * fsmc_nand_switch_ecc - switch the ECC operation between different engines
> + *
> + * @eccstrength		- the number of bits that could be corrected
> + *			  (1 - HW, 4 - SW BCH4)
> + */
> +int __maybe_unused fsmc_nand_switch_ecc(uint32_t eccstrength)
> +{
> +	struct nand_chip *nand;
> +	struct mtd_info *mtd;
> +	int err = 0;

You don't have to initialize it.

> +
> +	mtd = &nand_info[nand_curr_device];
> +	nand = mtd->priv;
> +
> +	/* Setup the ecc configurations again */
> +	if (eccstrength == 1) {
> +		nand->ecc.mode = NAND_ECC_HW;
> +		nand->ecc.bytes = 3;
> +		nand->ecc.strength = 1;
> +		nand->ecc.layout = &fsmc_ecc1_layout;
> +		nand->ecc.correct = nand_correct_data;
> +	} else {
> +		nand->ecc.mode = NAND_ECC_SOFT_BCH;
> +		nand->ecc.calculate = nand_bch_calculate_ecc;
> +		nand->ecc.correct = nand_bch_correct_data;
> +		nand->ecc.bytes = 7;
> +		nand->ecc.strength = 4;
> +		nand->ecc.layout = NULL;
> +	}
> +
> +	/* Update NAND handling after ECC mode switch */
> +	err = nand_scan_tail(mtd);
> +
> +	return err;
> +}
> +#endif /* CONFIG_SPL_BUILD */
> +
>  int fsmc_nand_init(struct nand_chip *nand)
>  {
>  	static int chip_nr;

Other than that:

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>

-- 
viresh