[U-Boot] [PATCH v3 1/2] usb: zynqmp: Add XHCI driver support

[U-Boot] [PATCH v3 1/2] usb: zynqmp: Add XHCI driver support

[Siva Durga Prasad Paladugu]

Added USB XHCI driver support for zynqmp.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
---
Changes for v3:
- Decreased the phy reset delay to 10 micro secs
- Defined base addresses in board config file as
  per review comment.
Changes for v2:
- Moved all from xhci-zynqmp.h to .c file as
  per review comment
- Removed ad-hoc function zynqmp_xhci_core_exit()
  as per review comment
---
 drivers/usb/host/Makefile          |    1 +
 drivers/usb/host/xhci-zynqmp.c     |  145 ++++++++++++++++++++++++++++++++++++
 include/configs/xilinx_zynqmp_ep.h |    2 +
 3 files changed, 148 insertions(+), 0 deletions(-)
 create mode 100644 drivers/usb/host/xhci-zynqmp.c

diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index f70f38c..645b990 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -54,6 +54,7 @@ obj-$(CONFIG_USB_EHCI_ZYNQ) += ehci-zynq.o
 # xhci
 obj-$(CONFIG_USB_XHCI) += xhci.o xhci-mem.o xhci-ring.o
 obj-$(CONFIG_USB_XHCI_DWC3) += xhci-dwc3.o
+obj-$(CONFIG_USB_XHCI_ZYNQMP) += xhci-zynqmp.o
 obj-$(CONFIG_USB_XHCI_KEYSTONE) += xhci-keystone.o
 obj-$(CONFIG_USB_XHCI_EXYNOS) += xhci-exynos5.o
 obj-$(CONFIG_USB_XHCI_FSL) += xhci-fsl.o
diff --git a/drivers/usb/host/xhci-zynqmp.c b/drivers/usb/host/xhci-zynqmp.c
new file mode 100644
index 0000000..6e4eb3a
--- /dev/null
+++ b/drivers/usb/host/xhci-zynqmp.c
@@ -0,0 +1,145 @@
+/*
+ * Copyright 2015 Xilinx, Inc.
+ *
+ * Zynq USB HOST xHCI Controller
+ *
+ * Author: Siva Durga Prasad Paladugu<sivadur@xilinx.com>
+ *
+ * This file was reused from Freescale USB xHCI
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <usb.h>
+#include <asm-generic/errno.h>
+#include <asm/arch-zynqmp/hardware.h>
+#include <linux/compat.h>
+#include <linux/usb/dwc3.h>
+#include "xhci.h"
+
+/* Declare global data pointer */
+DECLARE_GLOBAL_DATA_PTR;
+
+/* Default to the ZYNQMP XHCI defines */
+#define USB3_PWRCTL_CLK_CMD_MASK	0x3FE000
+#define USB3_PWRCTL_CLK_FREQ_MASK	0xFFC
+#define USB3_PHY_PARTIAL_RX_POWERON     BIT(6)
+#define USB3_PHY_RX_POWERON		BIT(14)
+#define USB3_PHY_TX_POWERON		BIT(15)
+#define USB3_PHY_TX_RX_POWERON	(USB3_PHY_RX_POWERON | USB3_PHY_TX_POWERON)
+#define USB3_PWRCTL_CLK_CMD_SHIFT   14
+#define USB3_PWRCTL_CLK_FREQ_SHIFT	22
+
+/* USBOTGSS_WRAPPER definitions */
+#define USBOTGSS_WRAPRESET	BIT(17)
+#define USBOTGSS_DMADISABLE BIT(16)
+#define USBOTGSS_STANDBYMODE_NO_STANDBY BIT(4)
+#define USBOTGSS_STANDBYMODE_SMRT		BIT(5)
+#define USBOTGSS_STANDBYMODE_SMRT_WKUP (0x3 << 4)
+#define USBOTGSS_IDLEMODE_NOIDLE BIT(2)
+#define USBOTGSS_IDLEMODE_SMRT BIT(3)
+#define USBOTGSS_IDLEMODE_SMRT_WKUP (0x3 << 2)
+
+/* USBOTGSS_IRQENABLE_SET_0 bit */
+#define USBOTGSS_COREIRQ_EN	BIT(1)
+
+/* USBOTGSS_IRQENABLE_SET_1 bits */
+#define USBOTGSS_IRQ_SET_1_IDPULLUP_FALL_EN	BIT(1)
+#define USBOTGSS_IRQ_SET_1_DISCHRGVBUS_FALL_EN	BIT(3)
+#define USBOTGSS_IRQ_SET_1_CHRGVBUS_FALL_EN	BIT(4)
+#define USBOTGSS_IRQ_SET_1_DRVVBUS_FALL_EN	BIT(5)
+#define USBOTGSS_IRQ_SET_1_IDPULLUP_RISE_EN	BIT(8)
+#define USBOTGSS_IRQ_SET_1_DISCHRGVBUS_RISE_EN	BIT(11)
+#define USBOTGSS_IRQ_SET_1_CHRGVBUS_RISE_EN	BIT(12)
+#define USBOTGSS_IRQ_SET_1_DRVVBUS_RISE_EN	BIT(13)
+#define USBOTGSS_IRQ_SET_1_OEVT_EN		BIT(16)
+#define USBOTGSS_IRQ_SET_1_DMADISABLECLR_EN	BIT(17)
+
+struct zynqmp_xhci {
+	struct xhci_hccr *hcd;
+	struct dwc3 *dwc3_reg;
+};
+
+static struct zynqmp_xhci zynqmp_xhci;
+
+unsigned long ctr_addr[] = CONFIG_ZYNQMP_XHCI_LIST;
+
+__weak int __board_usb_init(int index, enum usb_init_type init)
+{
+	return 0;
+}
+
+void usb_phy_reset(struct dwc3 *dwc3_reg)
+{
+	/* Assert USB3 PHY reset */
+	setbits_le32(&dwc3_reg->g_usb3pipectl[0], DWC3_GUSB3PIPECTL_PHYSOFTRST);
+
+	/* Assert USB2 PHY reset */
+	setbits_le32(&dwc3_reg->g_usb2phycfg, DWC3_GUSB2PHYCFG_PHYSOFTRST);
+
+	udelay(10);
+
+	/* Clear USB3 PHY reset */
+	clrbits_le32(&dwc3_reg->g_usb3pipectl[0], DWC3_GUSB3PIPECTL_PHYSOFTRST);
+
+	/* Clear USB2 PHY reset */
+	clrbits_le32(&dwc3_reg->g_usb2phycfg, DWC3_GUSB2PHYCFG_PHYSOFTRST);
+}
+
+static int zynqmp_xhci_core_init(struct zynqmp_xhci *zynqmp_xhci)
+{
+	int ret = 0;
+
+	ret = dwc3_core_init(zynqmp_xhci->dwc3_reg);
+	if (ret) {
+		debug("%s:failed to initialize core\n", __func__);
+		return ret;
+	}
+
+	/* We are hard-coding DWC3 core to Host Mode */
+	dwc3_set_mode(zynqmp_xhci->dwc3_reg, DWC3_GCTL_PRTCAP_HOST);
+
+	return ret;
+}
+
+int xhci_hcd_init(int index, struct xhci_hccr **hccr, struct xhci_hcor **hcor)
+{
+	struct zynqmp_xhci *ctx = &zynqmp_xhci;
+	int ret = 0;
+
+	ctx->hcd = (struct xhci_hccr *)ctr_addr[index];
+	ctx->dwc3_reg = (struct dwc3 *)((char *)(ctx->hcd) + DWC3_REG_OFFSET);
+
+	ret = board_usb_init(index, USB_INIT_HOST);
+	if (ret != 0) {
+		puts("Failed to initialize board for USB\n");
+		return ret;
+	}
+
+	ret = zynqmp_xhci_core_init(ctx);
+	if (ret < 0) {
+		puts("Failed to initialize xhci\n");
+		return ret;
+	}
+
+	*hccr = (struct xhci_hccr *)ctx->hcd;
+	*hcor = (struct xhci_hcor *)((uint32_t) *hccr
+				+ HC_LENGTH(xhci_readl(&(*hccr)->cr_capbase)));
+
+	debug("zynqmp-xhci: init hccr %x and hcor %x hc_length %d\n",
+	      (uint32_t)*hccr, (uint32_t)*hcor,
+	      (uint32_t)HC_LENGTH(xhci_readl(&(*hccr)->cr_capbase)));
+
+	return ret;
+}
+
+void xhci_hcd_stop(int index)
+{
+	/*
+	 * Currently zynqmp socs do not support PHY shutdown from
+	 * sw. But this support may be added in future socs.
+	 */
+
+	return 0;
+}
diff --git a/include/configs/xilinx_zynqmp_ep.h b/include/configs/xilinx_zynqmp_ep.h
index e476eb1..abb3c40 100644
--- a/include/configs/xilinx_zynqmp_ep.h
+++ b/include/configs/xilinx_zynqmp_ep.h
@@ -24,6 +24,8 @@
 #define CONFIG_SYS_I2C_ZYNQ
 #define CONFIG_ZYNQ_EEPROM
 #define CONFIG_AHCI
+#define CONFIG_ZYNQMP_XHCI_LIST {ZYNQMP_USB0_XHCI_BASEADDR, \
+				 ZYNQMP_USB1_XHCI_BASEADDR}
 
 #include <configs/xilinx_zynqmp.h>
 
-- 
1.7.1

[U-Boot] [PATCH v3 1/2] usb: zynqmp: Add XHCI driver support

[Siva Durga Prasad Paladugu]

Added USB XHCI driver support for zynqmp.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
---
Changes for v3:
- Decreased the phy reset delay to 10 micro secs
- Defined base addresses in board config file as
  per review comment.
Changes for v2:
- Moved all from xhci-zynqmp.h to .c file as
  per review comment
- Removed ad-hoc function zynqmp_xhci_core_exit()
  as per review comment
---
 drivers/usb/host/Makefile          |    1 +
 drivers/usb/host/xhci-zynqmp.c     |  145 ++++++++++++++++++++++++++++++++++++
 include/configs/xilinx_zynqmp_ep.h |    2 +
 3 files changed, 148 insertions(+), 0 deletions(-)
 create mode 100644 drivers/usb/host/xhci-zynqmp.c

diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index f70f38c..645b990 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -54,6 +54,7 @@ obj-$(CONFIG_USB_EHCI_ZYNQ) += ehci-zynq.o
 # xhci
 obj-$(CONFIG_USB_XHCI) += xhci.o xhci-mem.o xhci-ring.o
 obj-$(CONFIG_USB_XHCI_DWC3) += xhci-dwc3.o
+obj-$(CONFIG_USB_XHCI_ZYNQMP) += xhci-zynqmp.o
 obj-$(CONFIG_USB_XHCI_KEYSTONE) += xhci-keystone.o
 obj-$(CONFIG_USB_XHCI_EXYNOS) += xhci-exynos5.o
 obj-$(CONFIG_USB_XHCI_FSL) += xhci-fsl.o
diff --git a/drivers/usb/host/xhci-zynqmp.c b/drivers/usb/host/xhci-zynqmp.c
new file mode 100644
index 0000000..6e4eb3a
--- /dev/null
+++ b/drivers/usb/host/xhci-zynqmp.c
@@ -0,0 +1,145 @@
+/*
+ * Copyright 2015 Xilinx, Inc.
+ *
+ * Zynq USB HOST xHCI Controller
+ *
+ * Author: Siva Durga Prasad Paladugu<sivadur@xilinx.com>
+ *
+ * This file was reused from Freescale USB xHCI
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <usb.h>
+#include <asm-generic/errno.h>
+#include <asm/arch-zynqmp/hardware.h>
+#include <linux/compat.h>
+#include <linux/usb/dwc3.h>
+#include "xhci.h"
+
+/* Declare global data pointer */
+DECLARE_GLOBAL_DATA_PTR;
+
+/* Default to the ZYNQMP XHCI defines */
+#define USB3_PWRCTL_CLK_CMD_MASK	0x3FE000
+#define USB3_PWRCTL_CLK_FREQ_MASK	0xFFC
+#define USB3_PHY_PARTIAL_RX_POWERON     BIT(6)
+#define USB3_PHY_RX_POWERON		BIT(14)
+#define USB3_PHY_TX_POWERON		BIT(15)
+#define USB3_PHY_TX_RX_POWERON	(USB3_PHY_RX_POWERON | USB3_PHY_TX_POWERON)
+#define USB3_PWRCTL_CLK_CMD_SHIFT   14
+#define USB3_PWRCTL_CLK_FREQ_SHIFT	22
+
+/* USBOTGSS_WRAPPER definitions */
+#define USBOTGSS_WRAPRESET	BIT(17)
+#define USBOTGSS_DMADISABLE BIT(16)
+#define USBOTGSS_STANDBYMODE_NO_STANDBY BIT(4)
+#define USBOTGSS_STANDBYMODE_SMRT		BIT(5)
+#define USBOTGSS_STANDBYMODE_SMRT_WKUP (0x3 << 4)
+#define USBOTGSS_IDLEMODE_NOIDLE BIT(2)
+#define USBOTGSS_IDLEMODE_SMRT BIT(3)
+#define USBOTGSS_IDLEMODE_SMRT_WKUP (0x3 << 2)
+
+/* USBOTGSS_IRQENABLE_SET_0 bit */
+#define USBOTGSS_COREIRQ_EN	BIT(1)
+
+/* USBOTGSS_IRQENABLE_SET_1 bits */
+#define USBOTGSS_IRQ_SET_1_IDPULLUP_FALL_EN	BIT(1)
+#define USBOTGSS_IRQ_SET_1_DISCHRGVBUS_FALL_EN	BIT(3)
+#define USBOTGSS_IRQ_SET_1_CHRGVBUS_FALL_EN	BIT(4)
+#define USBOTGSS_IRQ_SET_1_DRVVBUS_FALL_EN	BIT(5)
+#define USBOTGSS_IRQ_SET_1_IDPULLUP_RISE_EN	BIT(8)
+#define USBOTGSS_IRQ_SET_1_DISCHRGVBUS_RISE_EN	BIT(11)
+#define USBOTGSS_IRQ_SET_1_CHRGVBUS_RISE_EN	BIT(12)
+#define USBOTGSS_IRQ_SET_1_DRVVBUS_RISE_EN	BIT(13)
+#define USBOTGSS_IRQ_SET_1_OEVT_EN		BIT(16)
+#define USBOTGSS_IRQ_SET_1_DMADISABLECLR_EN	BIT(17)
+
+struct zynqmp_xhci {
+	struct xhci_hccr *hcd;
+	struct dwc3 *dwc3_reg;
+};
+
+static struct zynqmp_xhci zynqmp_xhci;
+
+unsigned long ctr_addr[] = CONFIG_ZYNQMP_XHCI_LIST;
+
+__weak int __board_usb_init(int index, enum usb_init_type init)
+{
+	return 0;
+}
+
+void usb_phy_reset(struct dwc3 *dwc3_reg)
+{
+	/* Assert USB3 PHY reset */
+	setbits_le32(&dwc3_reg->g_usb3pipectl[0], DWC3_GUSB3PIPECTL_PHYSOFTRST);
+
+	/* Assert USB2 PHY reset */
+	setbits_le32(&dwc3_reg->g_usb2phycfg, DWC3_GUSB2PHYCFG_PHYSOFTRST);
+
+	udelay(10);
+
+	/* Clear USB3 PHY reset */
+	clrbits_le32(&dwc3_reg->g_usb3pipectl[0], DWC3_GUSB3PIPECTL_PHYSOFTRST);
+
+	/* Clear USB2 PHY reset */
+	clrbits_le32(&dwc3_reg->g_usb2phycfg, DWC3_GUSB2PHYCFG_PHYSOFTRST);
+}
+
+static int zynqmp_xhci_core_init(struct zynqmp_xhci *zynqmp_xhci)
+{
+	int ret = 0;
+
+	ret = dwc3_core_init(zynqmp_xhci->dwc3_reg);
+	if (ret) {
+		debug("%s:failed to initialize core\n", __func__);
+		return ret;
+	}
+
+	/* We are hard-coding DWC3 core to Host Mode */
+	dwc3_set_mode(zynqmp_xhci->dwc3_reg, DWC3_GCTL_PRTCAP_HOST);
+
+	return ret;
+}
+
+int xhci_hcd_init(int index, struct xhci_hccr **hccr, struct xhci_hcor **hcor)
+{
+	struct zynqmp_xhci *ctx = &zynqmp_xhci;
+	int ret = 0;
+
+	ctx->hcd = (struct xhci_hccr *)ctr_addr[index];
+	ctx->dwc3_reg = (struct dwc3 *)((char *)(ctx->hcd) + DWC3_REG_OFFSET);
+
+	ret = board_usb_init(index, USB_INIT_HOST);
+	if (ret != 0) {
+		puts("Failed to initialize board for USB\n");
+		return ret;
+	}
+
+	ret = zynqmp_xhci_core_init(ctx);
+	if (ret < 0) {
+		puts("Failed to initialize xhci\n");
+		return ret;
+	}
+
+	*hccr = (struct xhci_hccr *)ctx->hcd;
+	*hcor = (struct xhci_hcor *)((uint32_t) *hccr
+				+ HC_LENGTH(xhci_readl(&(*hccr)->cr_capbase)));
+
+	debug("zynqmp-xhci: init hccr %x and hcor %x hc_length %d\n",
+	      (uint32_t)*hccr, (uint32_t)*hcor,
+	      (uint32_t)HC_LENGTH(xhci_readl(&(*hccr)->cr_capbase)));
+
+	return ret;
+}
+
+void xhci_hcd_stop(int index)
+{
+	/*
+	 * Currently zynqmp socs do not support PHY shutdown from
+	 * sw. But this support may be added in future socs.
+	 */
+
+	return 0;
+}
diff --git a/include/configs/xilinx_zynqmp_ep.h b/include/configs/xilinx_zynqmp_ep.h
index e476eb1..abb3c40 100644
--- a/include/configs/xilinx_zynqmp_ep.h
+++ b/include/configs/xilinx_zynqmp_ep.h
@@ -24,6 +24,8 @@
 #define CONFIG_SYS_I2C_ZYNQ
 #define CONFIG_ZYNQ_EEPROM
 #define CONFIG_AHCI
+#define CONFIG_ZYNQMP_XHCI_LIST {ZYNQMP_USB0_XHCI_BASEADDR, \
+				 ZYNQMP_USB1_XHCI_BASEADDR}
 
 #include <configs/xilinx_zynqmp.h>
 
-- 
1.7.1

[U-Boot] [PATCH v3 2/2] usb: zynqmp: Enable USB XHCI support

[Siva Durga Prasad Paladugu]

Enable USB XHCI support for ZynqMP

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
---
Changes for v3:
- Removed extra space between # and define
  as per review comment
Changes for v2:
- None
---
 include/configs/xilinx_zynqmp.h |    8 ++++++++
 1 files changed, 8 insertions(+), 0 deletions(-)

diff --git a/include/configs/xilinx_zynqmp.h b/include/configs/xilinx_zynqmp.h
index da87188..46b951a 100644
--- a/include/configs/xilinx_zynqmp.h
+++ b/include/configs/xilinx_zynqmp.h
@@ -109,6 +109,14 @@
 #define CONFIG_SYS_LOAD_ADDR		0x8000000
 
 #if defined(CONFIG_ZYNQMP_USB)
+#define CONFIG_USB_XHCI_DWC3
+#define CONFIG_USB_XHCI
+#define CONFIG_USB_MAX_CONTROLLER_COUNT         1
+#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS      2
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_XHCI_ZYNQMP
+
 #define CONFIG_USB_DWC3
 #define CONFIG_USB_DWC3_GADGET
 
-- 
1.7.1

[U-Boot] [PATCH v3 1/2] usb: zynqmp: Add XHCI driver support

[Marek Vasut]

On Thursday, September 03, 2015 at 11:19:01 AM, Siva Durga Prasad Paladugu 
wrote:
> Added USB XHCI driver support for zynqmp.
> 
> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>

Hi,

is this V3 in any way different from the previous V3 ?

[...]

> +int xhci_hcd_init(int index, struct xhci_hccr **hccr, struct xhci_hcor
> **hcor) +{
> +	struct zynqmp_xhci *ctx = &zynqmp_xhci;
> +	int ret = 0;

You should sanitize the index here:

if (index < 0 || index > ARRAY_SIZE(ctr_addr))
	return -EINVAL;

> +	ctx->hcd = (struct xhci_hccr *)ctr_addr[index];
> +	ctx->dwc3_reg = (struct dwc3 *)((char *)(ctx->hcd) + DWC3_REG_OFFSET);
> +
> +	ret = board_usb_init(index, USB_INIT_HOST);
> +	if (ret != 0) {
> +		puts("Failed to initialize board for USB\n");
> +		return ret;
> +	}
> +
> +	ret = zynqmp_xhci_core_init(ctx);
> +	if (ret < 0) {
> +		puts("Failed to initialize xhci\n");
> +		return ret;
> +	}
> +
> +	*hccr = (struct xhci_hccr *)ctx->hcd;
> +	*hcor = (struct xhci_hcor *)((uint32_t) *hccr
> +				+ HC_LENGTH(xhci_readl(&(*hccr)->cr_capbase)));
> +
> +	debug("zynqmp-xhci: init hccr %x and hcor %x hc_length %d\n",
> +	      (uint32_t)*hccr, (uint32_t)*hcor,
> +	      (uint32_t)HC_LENGTH(xhci_readl(&(*hccr)->cr_capbase)));
> +
> +	return ret;
> +}
Otherwise,

Acked-by: Marek Vasut <marex@denx.de>

Best regards,
Marek Vasut

[U-Boot] [PATCH v3 1/2] usb: zynqmp: Add XHCI driver support

[Siva Durga Prasad Paladugu]

Hi Marek,

> -----Original Message-----
> From: Marek Vasut [mailto:marex at denx.de]
> Sent: Thursday, September 03, 2015 3:04 PM
> To: Siva Durga Prasad Paladugu
> Cc: u-boot at lists.denx.de; Siva Durga Prasad Paladugu
> Subject: Re: [PATCH v3 1/2] usb: zynqmp: Add XHCI driver support
>
> On Thursday, September 03, 2015 at 11:19:01 AM, Siva Durga Prasad
> Paladugu
> wrote:
> > Added USB XHCI driver support for zynqmp.
> >
> > Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
>
> Hi,
>
> is this V3 in any way different from the previous V3 ?

Its just same. I didn't get it in u-boot mailing list and hence sent it again.

Regards,
Siva
>
> [...]
>
> > +int xhci_hcd_init(int index, struct xhci_hccr **hccr, struct xhci_hcor
> > **hcor) +{
> > +   struct zynqmp_xhci *ctx = &zynqmp_xhci;
> > +   int ret = 0;
>
> You should sanitize the index here:
>
> if (index < 0 || index > ARRAY_SIZE(ctr_addr))
>       return -EINVAL;
>
> > +   ctx->hcd = (struct xhci_hccr *)ctr_addr[index];
> > +   ctx->dwc3_reg = (struct dwc3 *)((char *)(ctx->hcd) +
> DWC3_REG_OFFSET);
> > +
> > +   ret = board_usb_init(index, USB_INIT_HOST);
> > +   if (ret != 0) {
> > +           puts("Failed to initialize board for USB\n");
> > +           return ret;
> > +   }
> > +
> > +   ret = zynqmp_xhci_core_init(ctx);
> > +   if (ret < 0) {
> > +           puts("Failed to initialize xhci\n");
> > +           return ret;
> > +   }
> > +
> > +   *hccr = (struct xhci_hccr *)ctx->hcd;
> > +   *hcor = (struct xhci_hcor *)((uint32_t) *hccr
> > +                           + HC_LENGTH(xhci_readl(&(*hccr)-
> >cr_capbase)));
> > +
> > +   debug("zynqmp-xhci: init hccr %x and hcor %x hc_length %d\n",
> > +         (uint32_t)*hccr, (uint32_t)*hcor,
> > +         (uint32_t)HC_LENGTH(xhci_readl(&(*hccr)->cr_capbase)));
> > +
> > +   return ret;
> > +}
> Otherwise,
>
> Acked-by: Marek Vasut <marex@denx.de>
>
> Best regards,
> Marek Vasut


This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.

[U-Boot] [PATCH v3 1/2] usb: zynqmp: Add XHCI driver support

[Marek Vasut]

On Thursday, September 03, 2015 at 11:37:45 AM, Siva Durga Prasad Paladugu 
wrote:
> Hi Marek,

Hi,

> > -----Original Message-----
> > From: Marek Vasut [mailto:marex at denx.de]
> > Sent: Thursday, September 03, 2015 3:04 PM
> > To: Siva Durga Prasad Paladugu
> > Cc: u-boot at lists.denx.de; Siva Durga Prasad Paladugu
> > Subject: Re: [PATCH v3 1/2] usb: zynqmp: Add XHCI driver support
> > 
> > On Thursday, September 03, 2015 at 11:19:01 AM, Siva Durga Prasad
> > Paladugu
> > 
> > wrote:
> > > Added USB XHCI driver support for zynqmp.
> > > 
> > > Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
> > 
> > Hi,
> > 
> > is this V3 in any way different from the previous V3 ?
> 
> Its just same. I didn't get it in u-boot mailing list and hence sent it
> again.

Please add RESEND tag into the subject next time then.

Best regards,
Marek Vasut