From: Tom Rini <trini@konsulko.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [U-Boot, v2, 11/15] board/keymile/km82xx: setting dip_switch 3 and 4 will run bootloader
Date: Wed, 18 Nov 2015 17:37:04 -0500 [thread overview]
Message-ID: <20151118223704.GS8060@bill-the-cat> (raw)
In-Reply-To: <1447754018-12365-12-git-send-email-valentin.longchamp@keymile.com>
On Tue, Nov 17, 2015 at 10:53:34AM +0100, Valentin Longchamp wrote:
> From: Bagavathiannan Palanisamy <Bagavathiannan.Palanisamy@keymile.com>
>
> Setting dip_switch 3 and 4 also will run bootloader in COGE3 and COGE6
> It is required remove local mgmt IP address, when DIP Switch PIN3 is
> enabled. DIP Switch 4 also enabled to avoid u-boot update in future
> for DIP switch enhancements.
>
> Signed-off-by: Bagavathiannan Palanisamy <Bagavathiannan.Palanisamy@keymile.com>
> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Applied to u-boot/master, thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20151118/47eb8a2d/attachment.sig>
next prev parent reply other threads:[~2015-11-18 22:37 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-11-17 9:53 [U-Boot] [PATCH v2 00/15] km/powerpc: various bugfixes and support for 3 new boards Valentin Longchamp
2015-11-17 9:53 ` [U-Boot] [PATCH v2 01/15] powerpc/83xx: add support for kmtepr2 board Valentin Longchamp
2015-11-18 22:36 ` [U-Boot] [U-Boot, v2, " Tom Rini
2015-11-17 9:53 ` [U-Boot] [PATCH v2 02/15] powerpc/82xx: make set/get_pin for km82xx more flexible Valentin Longchamp
2015-11-18 22:36 ` [U-Boot] [U-Boot, v2, " Tom Rini
2015-11-17 9:53 ` [U-Boot] [PATCH v2 03/15] powerpc/82xx/km: add testpin detection for mgcoge3ne Valentin Longchamp
2015-11-18 22:36 ` [U-Boot] [U-Boot, v2, " Tom Rini
2015-11-17 9:53 ` [U-Boot] [PATCH v2 04/15] km/powerpc: increase space for kernel imange and FDT blob Valentin Longchamp
2015-11-18 22:36 ` [U-Boot] [U-Boot, v2, " Tom Rini
2015-11-17 9:53 ` [U-Boot] [PATCH v2 05/15] km/powerpc: move open firmware defines to km-powerpc.h Valentin Longchamp
2015-11-18 22:36 ` [U-Boot] [U-Boot, v2, " Tom Rini
2015-11-17 9:53 ` [U-Boot] [PATCH v2 06/15] km/powerpc: remove unneeded defines Valentin Longchamp
2015-11-18 22:36 ` [U-Boot] [U-Boot,v2,06/15] " Tom Rini
2015-11-17 9:53 ` [U-Boot] [PATCH v2 07/15] km/powerpc82xx: remove unused function Valentin Longchamp
2015-11-18 22:36 ` [U-Boot] [U-Boot, v2, " Tom Rini
2015-11-17 9:53 ` [U-Boot] [PATCH v2 08/15] powerpc/km8321: define CONFIG_SYS_DDRCDR Valentin Longchamp
2015-11-18 22:36 ` [U-Boot] [U-Boot, v2, " Tom Rini
2015-11-17 9:53 ` [U-Boot] [PATCH v2 09/15] powerpc/km8309: " Valentin Longchamp
2015-11-18 22:36 ` [U-Boot] [U-Boot, v2, " Tom Rini
2015-11-17 9:53 ` [U-Boot] [PATCH v2 10/15] powerpc/km8360: fix the ODT parameters for CS0 Valentin Longchamp
2015-11-18 22:36 ` [U-Boot] [U-Boot, v2, " Tom Rini
2015-11-17 9:53 ` [U-Boot] [PATCH v2 11/15] board/keymile/km82xx: setting dip_switch 3 and 4 will run bootloader Valentin Longchamp
2015-11-18 22:37 ` Tom Rini [this message]
2015-11-17 9:53 ` [U-Boot] [PATCH v2 12/15] km83xx: use CONFIG_ENV_ADDR for the newenv env command Valentin Longchamp
2015-11-18 22:37 ` [U-Boot] [U-Boot, v2, " Tom Rini
2015-11-17 9:53 ` [U-Boot] [PATCH v2 13/15] km8309: change the default QE_FW address Valentin Longchamp
2015-11-18 22:37 ` [U-Boot] [U-Boot, v2, " Tom Rini
2015-11-17 9:53 ` [U-Boot] [PATCH v2 14/15] powerpc/83xx: add support for kmtegr1 board Valentin Longchamp
2015-11-18 22:37 ` [U-Boot] [U-Boot, v2, " Tom Rini
2015-11-17 9:53 ` [U-Boot] [PATCH v2 15/15] km/powerpc: fix ft_board_setup prototype for km82xx & km83xx Valentin Longchamp
2015-11-18 22:37 ` [U-Boot] [U-Boot, v2, " Tom Rini
2015-11-17 10:57 ` [U-Boot] [PATCH v2 00/15] km/powerpc: various bugfixes and support for 3 new boards Heiko Schocher
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20151118223704.GS8060@bill-the-cat \
--to=trini@konsulko.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox