[U-Boot] [PATCH] arm: socfpga: Enabling MTD default partitions

[Marek Vasut <marex@denx.de>]

On Monday, December 21, 2015 at 02:23:54 PM, Chin Liang See wrote:
> Enabling MTD default partitions if its not defined in board
> configuration file. The layout as below
> 
> > u-boot partition for storing SPL image

But there's also U-Boot image here

> > env partition for storing U-Boot environment

There are two partitions for the environment ... I think you can just point
to the layout below and dont need to list it in the commit message.

> > UBI partition for storing kernel image and filesystem
> > boot partition for backward compatibility / raw binary
> > rootfs partition for storing filesystem in case boot partition used
> 
> Signed-off-by: Chin Liang See <clsee@altera.com>
> Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
> Cc: Dinh Nguyen <dinh.linux@gmail.com>
> Cc: Pavel Machek <pavel@denx.de>
> Cc: Marek Vasut <marex@denx.de>
> Cc: Stefan Roese <sr@denx.de>
> ---
>  include/configs/socfpga_common.h |   23 +++++++++++++++++++++++
>  1 files changed, 23 insertions(+), 0 deletions(-)
> 
> diff --git a/include/configs/socfpga_common.h
> b/include/configs/socfpga_common.h index 699e78a..36fc9f0 100644
> --- a/include/configs/socfpga_common.h
> +++ b/include/configs/socfpga_common.h
> @@ -271,6 +271,29 @@ unsigned int cm_get_qspi_controller_clk_hz(void);
>  #define CONFIG_SYS_CONSOLE_ENV_OVERWRITE
>  #define CONFIG_ENV_SIZE			4096
> 
> +/*
> + * mtd partitioning for serial NOR flash
> + *
> + * device nor0 <ff705000.spi>, # parts = 6
> + * #: name                size            offset          mask_flags
> + * 0: u-boot              0x00100000      0x00000000      0
> + * 1: env1                0x00040000      0x00100000      0
> + * 2: env2                0x00040000      0x00140000      0
> + * 3: UBI                 0x03e80000      0x00180000      0
> + * 4: boot                0x00e80000      0x00180000      0
> + * 5: rootfs              0x01000000      0x01000000      0
> + *
> + */
> +#if defined(CONFIG_CMD_SF) || !defined(MTDPARTS_DEFAULT)

This should be &&, right ?

> +#define MTDPARTS_DEFAULT	"mtdparts=ff705000.spi:"\

Make this ff705000.spi.0 please , otherwise it'd be impossible to support 
multiple SPI NORs on a single QSPI controller (the mtdparts would get bound
to all of them)

> +				"1m(u-boot),"		\
> +				"256k(env1),"		\
> +				"256k(env2),"		\
> +				"14848k(boot),"		\
> +				"16m(rootfs),"		\
> +				"- at 1536k(UBI)\0"
> +#endif
> +
>  /* Environment for SDMMC boot */
>  #if defined(CONFIG_ENV_IS_IN_MMC) && !defined(CONFIG_ENV_OFFSET)
>  #define CONFIG_SYS_MMC_ENV_DEV		0	/* device 0 */

Best regards,
Marek Vasut