* [U-Boot] [PATCH 1/2] [PATCH 1/2] ARM: sun7i: config: add config for Sinovoip/Bananapi BPI-R1
@ 2016-10-03 20:01 Stephen Arnold
2016-10-03 20:01 ` [U-Boot] [PATCH 2/2] [PATCH 2/2] ARM: sun7i: dts: add support " Stephen Arnold
2016-10-03 20:01 ` [U-Boot] [PATCH] " Stephen Arnold
0 siblings, 2 replies; 5+ messages in thread
From: Stephen Arnold @ 2016-10-03 20:01 UTC (permalink / raw)
To: u-boot
From: Steve Arnold <stephen.arnold42@gmail.com>
* needs different GMAC_TX_DELAY than lamobo-r1 (not compatible)
Signed-off-by: Steve Arnold <stephen.arnold42@gmail.com>
---
configs/Bananapi_R1_defconfig | 16 ++++++++++++++++
1 file changed, 16 insertions(+)
create mode 100644 configs/Bananapi_R1_defconfig
diff --git a/configs/Bananapi_R1_defconfig b/configs/Bananapi_R1_defconfig
new file mode 100644
index 0000000..3743d5c
--- /dev/null
+++ b/configs/Bananapi_R1_defconfig
@@ -0,0 +1,16 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN7I=y
+CONFIG_DRAM_CLK=432
+CONFIG_GMAC_TX_DELAY=3
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-bananapi-r1"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,RGMII,MACPWR=SUNXI_GPH(23),AHCI,USB_EHCI"
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_USB_EHCI_HCD=y
+CONFIG_DM_ETH=y
+CONFIG_PHYLIB=y
+# CONFIG_RTL8211X_PHY_FORCE_MASTER=y
--
2.9.3
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [U-Boot] [PATCH 2/2] [PATCH 2/2] ARM: sun7i: dts: add support for Sinovoip/Bananapi BPI-R1
2016-10-03 20:01 [U-Boot] [PATCH 1/2] [PATCH 1/2] ARM: sun7i: config: add config for Sinovoip/Bananapi BPI-R1 Stephen Arnold
@ 2016-10-03 20:01 ` Stephen Arnold
2016-10-03 20:01 ` [U-Boot] [PATCH] " Stephen Arnold
1 sibling, 0 replies; 5+ messages in thread
From: Stephen Arnold @ 2016-10-03 20:01 UTC (permalink / raw)
To: u-boot
From: Steve Arnold <stephen.arnold42@gmail.com>
* changes from lamobo-r1 required include:
- ahci power pin (remove)
- usbvbus pin config
- mmc pin config
- uart2 enable
Signed-off-by: Steve Arnold <stephen.arnold42@gmail.com>
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/sun7i-a20-bananapi-r1.dts | 376 +++++++++++++++++++++++++++++++++
2 files changed, 377 insertions(+)
create mode 100644 arch/arm/dts/sun7i-a20-bananapi-r1.dts
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 032c5ae..0cbae00 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -216,6 +216,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
sun7i-a20-ainol-aw1.dtb \
sun7i-a20-bananapi.dtb \
sun7i-a20-bananapi-m1-plus.dtb \
+ sun7i-a20-bananapi-r1.dtb \
sun7i-a20-bananapro.dtb \
sun7i-a20-cubieboard2.dtb \
sun7i-a20-cubietruck.dtb \
diff --git a/arch/arm/dts/sun7i-a20-bananapi-r1.dts b/arch/arm/dts/sun7i-a20-bananapi-r1.dts
new file mode 100644
index 0000000..1a550f9
--- /dev/null
+++ b/arch/arm/dts/sun7i-a20-bananapi-r1.dts
@@ -0,0 +1,376 @@
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ * Changes copyright 2016 Stephen Arnold <nerdboy@gentoo.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Banana Pi BPI-R1";
+ compatible = "sinovoip,bpi-r1", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart2;
+ serial2 = &uart3;
+ serial3 = &uart7;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_bpi_r1>;
+
+ green {
+ label = "bpi-r1:green:usr";
+ gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>; /* PH24 */
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_power_pin_bpi_r1>;
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>; /* PH23 */
+ };
+
+};
+
+&ahci {
+ target-supply = <®_ahci_5v>;
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_rgmii_a>;
+ phy = <&phy1>;
+ phy-mode = "rgmii";
+ phy-supply = <®_gmac_3v3>;
+ status = "okay";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch: ethernet-switch at 1e {
+ compatible = "brcm,bcm53125";
+ reg = <30>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port0: port at 0 {
+ reg = <0>;
+ label = "lan2";
+ };
+
+ port1: port at 1 {
+ reg = <1>;
+ label = "lan3";
+ };
+
+ port2: port at 2 {
+ reg = <2>;
+ label = "lan4";
+ };
+
+ port3: port at 3 {
+ reg = <3>;
+ label = "wan";
+ };
+
+ port4: port at 4 {
+ reg = <4>;
+ label = "lan1";
+ };
+
+ port8: port at 8 {
+ reg = <8>;
+ label = "cpu";
+ ethernet = <&gmac>;
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic at 34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+#include "axp209.dtsi"
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_rx_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bpi_r1>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+&pio {
+ usb0_id_detect_pin: usb0_id_detect_pin at 0 {
+ allwinner,pins = "PH4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb0_vbus_detect_pin: usb0_vbus_detect_pin at 0 {
+ allwinner,pins = "PH5";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb0_vbus_pin_bpi_r1: usb0_vbus_pin at 0 {
+ allwinner,pins = "PB9";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb2_vbus_pin_bpi_r1: usb2_vbus_pin at 0 {
+ allwinner,pins = "PH3";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin_bpi_r1: mmc0_cd_pin at 0 {
+ allwinner,pins = "PH1";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ gmac_power_pin_bpi_r1: gmac_power_pin at 0 {
+ allwinner,pins = "PH23";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ led_pins_bpi_r1: led_pins at 0 {
+ allwinner,pins = "PH24";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_ahci_5v {
+ status = "okay";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_usb0_vbus {
+ pinctrl-0 = <&usb0_vbus_pin_bpi_r1>;
+ gpio = <&pio 1 9 GPIO_ACTIVE_HIGH>; /* PB9 */
+ status = "okay";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ pinctrl-0 = <&usb2_vbus_pin_bpi_r1>;
+ gpio = <&pio 7 3 GPIO_ACTIVE_HIGH>; /* PH3 */
+ status = "okay";
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins_a>,
+ <&spi0_cs0_pins_a>,
+ <&spi0_cs1_pins_a>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins_a>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins_b>;
+ status = "okay";
+};
+
+&uart7 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart7_pins_a>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
+&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>;
+ usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb0_vbus_power-supply = <&usb_power_supply>;
+ usb0_vbus-supply = <®_usb0_vbus>;
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--
2.9.3
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [U-Boot] [PATCH] [PATCH 2/2] ARM: sun7i: dts: add support for Sinovoip/Bananapi BPI-R1
2016-10-03 20:01 [U-Boot] [PATCH 1/2] [PATCH 1/2] ARM: sun7i: config: add config for Sinovoip/Bananapi BPI-R1 Stephen Arnold
2016-10-03 20:01 ` [U-Boot] [PATCH 2/2] [PATCH 2/2] ARM: sun7i: dts: add support " Stephen Arnold
@ 2016-10-03 20:01 ` Stephen Arnold
2016-10-03 20:19 ` Stephen Arnold
1 sibling, 1 reply; 5+ messages in thread
From: Stephen Arnold @ 2016-10-03 20:01 UTC (permalink / raw)
To: u-boot
From: Steve Arnold <stephen.arnold42@gmail.com>
* changes from lamobo-r1 required include:
- ahci power pin (remove)
- usbvbus pin config
- mmc pin config
- uart2 enable
Signed-off-by: Steve Arnold <stephen.arnold42@gmail.com>
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/sun7i-a20-bananapi-r1.dts | 376 +++++++++++++++++++++++++++++++++
2 files changed, 377 insertions(+)
create mode 100644 arch/arm/dts/sun7i-a20-bananapi-r1.dts
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 032c5ae..0cbae00 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -216,6 +216,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
sun7i-a20-ainol-aw1.dtb \
sun7i-a20-bananapi.dtb \
sun7i-a20-bananapi-m1-plus.dtb \
+ sun7i-a20-bananapi-r1.dtb \
sun7i-a20-bananapro.dtb \
sun7i-a20-cubieboard2.dtb \
sun7i-a20-cubietruck.dtb \
diff --git a/arch/arm/dts/sun7i-a20-bananapi-r1.dts b/arch/arm/dts/sun7i-a20-bananapi-r1.dts
new file mode 100644
index 0000000..1a550f9
--- /dev/null
+++ b/arch/arm/dts/sun7i-a20-bananapi-r1.dts
@@ -0,0 +1,376 @@
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ * Changes copyright 2016 Stephen Arnold <nerdboy@gentoo.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Banana Pi BPI-R1";
+ compatible = "sinovoip,bpi-r1", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart2;
+ serial2 = &uart3;
+ serial3 = &uart7;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_bpi_r1>;
+
+ green {
+ label = "bpi-r1:green:usr";
+ gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>; /* PH24 */
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_power_pin_bpi_r1>;
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>; /* PH23 */
+ };
+
+};
+
+&ahci {
+ target-supply = <®_ahci_5v>;
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_rgmii_a>;
+ phy = <&phy1>;
+ phy-mode = "rgmii";
+ phy-supply = <®_gmac_3v3>;
+ status = "okay";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch: ethernet-switch at 1e {
+ compatible = "brcm,bcm53125";
+ reg = <30>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port0: port at 0 {
+ reg = <0>;
+ label = "lan2";
+ };
+
+ port1: port at 1 {
+ reg = <1>;
+ label = "lan3";
+ };
+
+ port2: port at 2 {
+ reg = <2>;
+ label = "lan4";
+ };
+
+ port3: port at 3 {
+ reg = <3>;
+ label = "wan";
+ };
+
+ port4: port at 4 {
+ reg = <4>;
+ label = "lan1";
+ };
+
+ port8: port at 8 {
+ reg = <8>;
+ label = "cpu";
+ ethernet = <&gmac>;
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic at 34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+#include "axp209.dtsi"
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_rx_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bpi_r1>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+&pio {
+ usb0_id_detect_pin: usb0_id_detect_pin at 0 {
+ allwinner,pins = "PH4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb0_vbus_detect_pin: usb0_vbus_detect_pin at 0 {
+ allwinner,pins = "PH5";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb0_vbus_pin_bpi_r1: usb0_vbus_pin at 0 {
+ allwinner,pins = "PB9";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb2_vbus_pin_bpi_r1: usb2_vbus_pin at 0 {
+ allwinner,pins = "PH3";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin_bpi_r1: mmc0_cd_pin at 0 {
+ allwinner,pins = "PH1";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ gmac_power_pin_bpi_r1: gmac_power_pin at 0 {
+ allwinner,pins = "PH23";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ led_pins_bpi_r1: led_pins at 0 {
+ allwinner,pins = "PH24";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_ahci_5v {
+ status = "okay";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_usb0_vbus {
+ pinctrl-0 = <&usb0_vbus_pin_bpi_r1>;
+ gpio = <&pio 1 9 GPIO_ACTIVE_HIGH>; /* PB9 */
+ status = "okay";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ pinctrl-0 = <&usb2_vbus_pin_bpi_r1>;
+ gpio = <&pio 7 3 GPIO_ACTIVE_HIGH>; /* PH3 */
+ status = "okay";
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins_a>,
+ <&spi0_cs0_pins_a>,
+ <&spi0_cs1_pins_a>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins_a>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins_b>;
+ status = "okay";
+};
+
+&uart7 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart7_pins_a>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
+&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>;
+ usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb0_vbus_power-supply = <&usb_power_supply>;
+ usb0_vbus-supply = <®_usb0_vbus>;
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--
2.9.3
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [U-Boot] [PATCH] [PATCH 2/2] ARM: sun7i: dts: add support for Sinovoip/Bananapi BPI-R1
2016-10-03 20:01 ` [U-Boot] [PATCH] " Stephen Arnold
@ 2016-10-03 20:19 ` Stephen Arnold
2016-10-03 20:21 ` Stephen Arnold
0 siblings, 1 reply; 5+ messages in thread
From: Stephen Arnold @ 2016-10-03 20:19 UTC (permalink / raw)
To: u-boot
Okay, please disregard the update with double "PATCH" in the subject;
I need to get better with git send-email (besides just the Google
insecure app thing for gmail).
I'm about to resend v2 with (hopefully) all the right stuff in it.
Thanks, Steve
On Mon, Oct 3, 2016 at 1:01 PM, Stephen Arnold
<stephen.arnold42@gmail.com> wrote:
> From: Steve Arnold <stephen.arnold42@gmail.com>
>
> * changes from lamobo-r1 required include:
> - ahci power pin (remove)
> - usbvbus pin config
> - mmc pin config
> - uart2 enable
>
> Signed-off-by: Steve Arnold <stephen.arnold42@gmail.com>
> ---
> arch/arm/dts/Makefile | 1 +
> arch/arm/dts/sun7i-a20-bananapi-r1.dts | 376 +++++++++++++++++++++++++++++++++
> 2 files changed, 377 insertions(+)
> create mode 100644 arch/arm/dts/sun7i-a20-bananapi-r1.dts
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 032c5ae..0cbae00 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -216,6 +216,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
> sun7i-a20-ainol-aw1.dtb \
> sun7i-a20-bananapi.dtb \
> sun7i-a20-bananapi-m1-plus.dtb \
> + sun7i-a20-bananapi-r1.dtb \
> sun7i-a20-bananapro.dtb \
> sun7i-a20-cubieboard2.dtb \
> sun7i-a20-cubietruck.dtb \
> diff --git a/arch/arm/dts/sun7i-a20-bananapi-r1.dts b/arch/arm/dts/sun7i-a20-bananapi-r1.dts
> new file mode 100644
> index 0000000..1a550f9
> --- /dev/null
> +++ b/arch/arm/dts/sun7i-a20-bananapi-r1.dts
> @@ -0,0 +1,376 @@
> +/*
> + * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
> + * Changes copyright 2016 Stephen Arnold <nerdboy@gentoo.org>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "sun7i-a20.dtsi"
> +#include "sunxi-common-regulators.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/pinctrl/sun4i-a10.h>
> +
> +/ {
> + model = "Banana Pi BPI-R1";
> + compatible = "sinovoip,bpi-r1", "allwinner,sun7i-a20";
> +
> + aliases {
> + serial0 = &uart0;
> + serial1 = &uart2;
> + serial2 = &uart3;
> + serial3 = &uart7;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&led_pins_bpi_r1>;
> +
> + green {
> + label = "bpi-r1:green:usr";
> + gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>; /* PH24 */
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + reg_gmac_3v3: gmac-3v3 {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&gmac_power_pin_bpi_r1>;
> + regulator-name = "gmac-3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + startup-delay-us = <100000>;
> + enable-active-high;
> + gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>; /* PH23 */
> + };
> +
> +};
> +
> +&ahci {
> + target-supply = <®_ahci_5v>;
> + status = "okay";
> +};
> +
> +&cpu0 {
> + cpu-supply = <®_dcdc2>;
> +};
> +
> +&ehci0 {
> + status = "okay";
> +};
> +
> +&ehci1 {
> + status = "okay";
> +};
> +
> +&ohci0 {
> + status = "okay";
> +};
> +
> +&ohci1 {
> + status = "okay";
> +};
> +
> +&gmac {
> + pinctrl-names = "default";
> + pinctrl-0 = <&gmac_pins_rgmii_a>;
> + phy = <&phy1>;
> + phy-mode = "rgmii";
> + phy-supply = <®_gmac_3v3>;
> + status = "okay";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> +
> + mdio {
> + compatible = "snps,dwmac-mdio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + switch: ethernet-switch at 1e {
> + compatible = "brcm,bcm53125";
> + reg = <30>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port0: port at 0 {
> + reg = <0>;
> + label = "lan2";
> + };
> +
> + port1: port at 1 {
> + reg = <1>;
> + label = "lan3";
> + };
> +
> + port2: port at 2 {
> + reg = <2>;
> + label = "lan4";
> + };
> +
> + port3: port at 3 {
> + reg = <3>;
> + label = "wan";
> + };
> +
> + port4: port at 4 {
> + reg = <4>;
> + label = "lan1";
> + };
> +
> + port8: port at 8 {
> + reg = <8>;
> + label = "cpu";
> + ethernet = <&gmac>;
> + phy-mode = "rgmii";
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> + };
> + };
> + };
> +};
> +
> +&i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0_pins_a>;
> + status = "okay";
> +
> + axp209: pmic at 34 {
> + compatible = "x-powers,axp209";
> + reg = <0x34>;
> + interrupt-parent = <&nmi_intc>;
> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> +
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + };
> +};
> +
> +#include "axp209.dtsi"
> +
> +&i2c2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c2_pins_a>;
> + status = "okay";
> +};
> +
> +&ir0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&ir0_rx_pins_a>;
> + status = "okay";
> +};
> +
> +&mmc0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bpi_r1>;
> + vmmc-supply = <®_vcc3v3>;
> + bus-width = <4>;
> + cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
> + cd-inverted;
> + status = "okay";
> +};
> +
> +&otg_sram {
> + status = "okay";
> +};
> +
> +&pio {
> + usb0_id_detect_pin: usb0_id_detect_pin at 0 {
> + allwinner,pins = "PH4";
> + allwinner,function = "gpio_in";
> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> + };
> +
> + usb0_vbus_detect_pin: usb0_vbus_detect_pin at 0 {
> + allwinner,pins = "PH5";
> + allwinner,function = "gpio_in";
> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> + };
> +
> + usb0_vbus_pin_bpi_r1: usb0_vbus_pin at 0 {
> + allwinner,pins = "PB9";
> + allwinner,function = "gpio_out";
> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> + };
> +
> + usb2_vbus_pin_bpi_r1: usb2_vbus_pin at 0 {
> + allwinner,pins = "PH3";
> + allwinner,function = "gpio_out";
> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> + };
> +
> + mmc0_cd_pin_bpi_r1: mmc0_cd_pin at 0 {
> + allwinner,pins = "PH1";
> + allwinner,function = "gpio_in";
> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
> + };
> +
> + gmac_power_pin_bpi_r1: gmac_power_pin at 0 {
> + allwinner,pins = "PH23";
> + allwinner,function = "gpio_out";
> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> + };
> +
> + led_pins_bpi_r1: led_pins at 0 {
> + allwinner,pins = "PH24";
> + allwinner,function = "gpio_out";
> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> + };
> +};
> +
> +®_ahci_5v {
> + status = "okay";
> +};
> +
> +®_dcdc2 {
> + regulator-always-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1400000>;
> + regulator-name = "vdd-cpu";
> +};
> +
> +®_dcdc3 {
> + regulator-always-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1400000>;
> + regulator-name = "vdd-int-dll";
> +};
> +
> +®_ldo1 {
> + regulator-name = "vdd-rtc";
> +};
> +
> +®_ldo2 {
> + regulator-always-on;
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-name = "avcc";
> +};
> +
> +®_usb0_vbus {
> + pinctrl-0 = <&usb0_vbus_pin_bpi_r1>;
> + gpio = <&pio 1 9 GPIO_ACTIVE_HIGH>; /* PB9 */
> + status = "okay";
> +};
> +
> +®_usb1_vbus {
> + status = "okay";
> +};
> +
> +®_usb2_vbus {
> + pinctrl-0 = <&usb2_vbus_pin_bpi_r1>;
> + gpio = <&pio 7 3 GPIO_ACTIVE_HIGH>; /* PH3 */
> + status = "okay";
> +};
> +
> +&spi0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi0_pins_a>,
> + <&spi0_cs0_pins_a>,
> + <&spi0_cs1_pins_a>;
> + status = "okay";
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_pins_a>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart2_pins_a>;
> + status = "okay";
> +};
> +
> +&uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart3_pins_b>;
> + status = "okay";
> +};
> +
> +&uart7 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart7_pins_a>;
> + status = "okay";
> +};
> +
> +&usb_otg {
> + dr_mode = "otg";
> + status = "okay";
> +};
> +
> +&usb_power_supply {
> + status = "okay";
> +};
> +
> +&usbphy {
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb0_id_detect_pin>;
> + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
> + usb0_vbus_power-supply = <&usb_power_supply>;
> + usb0_vbus-supply = <®_usb0_vbus>;
> + usb1_vbus-supply = <®_usb1_vbus>;
> + usb2_vbus-supply = <®_usb2_vbus>;
> + status = "okay";
> +};
> --
> 2.9.3
>
^ permalink raw reply [flat|nested] 5+ messages in thread
* [U-Boot] [PATCH] [PATCH 2/2] ARM: sun7i: dts: add support for Sinovoip/Bananapi BPI-R1
2016-10-03 20:19 ` Stephen Arnold
@ 2016-10-03 20:21 ` Stephen Arnold
0 siblings, 0 replies; 5+ messages in thread
From: Stephen Arnold @ 2016-10-03 20:21 UTC (permalink / raw)
To: u-boot
This is what I have now for send command:
git send-email --to=u-boot at lists.denx.de --confirm=always -M -1
--subject-prefix="PATCH v2" outgoing/*
Any u-boot-y tips are appreciated...
Steve
On Mon, Oct 3, 2016 at 1:19 PM, Stephen Arnold
<stephen.arnold42@gmail.com> wrote:
> Okay, please disregard the update with double "PATCH" in the subject;
> I need to get better with git send-email (besides just the Google
> insecure app thing for gmail).
>
> I'm about to resend v2 with (hopefully) all the right stuff in it.
>
> Thanks, Steve
>
> On Mon, Oct 3, 2016 at 1:01 PM, Stephen Arnold
> <stephen.arnold42@gmail.com> wrote:
>> From: Steve Arnold <stephen.arnold42@gmail.com>
>>
>> * changes from lamobo-r1 required include:
>> - ahci power pin (remove)
>> - usbvbus pin config
>> - mmc pin config
>> - uart2 enable
>>
>> Signed-off-by: Steve Arnold <stephen.arnold42@gmail.com>
>> ---
>> arch/arm/dts/Makefile | 1 +
>> arch/arm/dts/sun7i-a20-bananapi-r1.dts | 376 +++++++++++++++++++++++++++++++++
>> 2 files changed, 377 insertions(+)
>> create mode 100644 arch/arm/dts/sun7i-a20-bananapi-r1.dts
>>
>> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
>> index 032c5ae..0cbae00 100644
>> --- a/arch/arm/dts/Makefile
>> +++ b/arch/arm/dts/Makefile
>> @@ -216,6 +216,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
>> sun7i-a20-ainol-aw1.dtb \
>> sun7i-a20-bananapi.dtb \
>> sun7i-a20-bananapi-m1-plus.dtb \
>> + sun7i-a20-bananapi-r1.dtb \
>> sun7i-a20-bananapro.dtb \
>> sun7i-a20-cubieboard2.dtb \
>> sun7i-a20-cubietruck.dtb \
>> diff --git a/arch/arm/dts/sun7i-a20-bananapi-r1.dts b/arch/arm/dts/sun7i-a20-bananapi-r1.dts
>> new file mode 100644
>> index 0000000..1a550f9
>> --- /dev/null
>> +++ b/arch/arm/dts/sun7i-a20-bananapi-r1.dts
>> @@ -0,0 +1,376 @@
>> +/*
>> + * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
>> + * Changes copyright 2016 Stephen Arnold <nerdboy@gentoo.org>
>> + *
>> + * This file is dual-licensed: you can use it either under the terms
>> + * of the GPL or the X11 license, at your option. Note that this dual
>> + * licensing only applies to this file, and not this project as a
>> + * whole.
>> + *
>> + * a) This file is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation; either version 2 of the
>> + * License, or (at your option) any later version.
>> + *
>> + * This file is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + *
>> + * Or, alternatively,
>> + *
>> + * b) Permission is hereby granted, free of charge, to any person
>> + * obtaining a copy of this software and associated documentation
>> + * files (the "Software"), to deal in the Software without
>> + * restriction, including without limitation the rights to use,
>> + * copy, modify, merge, publish, distribute, sublicense, and/or
>> + * sell copies of the Software, and to permit persons to whom the
>> + * Software is furnished to do so, subject to the following
>> + * conditions:
>> + *
>> + * The above copyright notice and this permission notice shall be
>> + * included in all copies or substantial portions of the Software.
>> + *
>> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
>> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
>> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
>> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
>> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
>> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
>> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
>> + * OTHER DEALINGS IN THE SOFTWARE.
>> + */
>> +
>> +/dts-v1/;
>> +#include "sun7i-a20.dtsi"
>> +#include "sunxi-common-regulators.dtsi"
>> +
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/interrupt-controller/irq.h>
>> +#include <dt-bindings/pinctrl/sun4i-a10.h>
>> +
>> +/ {
>> + model = "Banana Pi BPI-R1";
>> + compatible = "sinovoip,bpi-r1", "allwinner,sun7i-a20";
>> +
>> + aliases {
>> + serial0 = &uart0;
>> + serial1 = &uart2;
>> + serial2 = &uart3;
>> + serial3 = &uart7;
>> + };
>> +
>> + chosen {
>> + stdout-path = "serial0:115200n8";
>> + };
>> +
>> + leds {
>> + compatible = "gpio-leds";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&led_pins_bpi_r1>;
>> +
>> + green {
>> + label = "bpi-r1:green:usr";
>> + gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>; /* PH24 */
>> + linux,default-trigger = "heartbeat";
>> + };
>> + };
>> +
>> + reg_gmac_3v3: gmac-3v3 {
>> + compatible = "regulator-fixed";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&gmac_power_pin_bpi_r1>;
>> + regulator-name = "gmac-3v3";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + startup-delay-us = <100000>;
>> + enable-active-high;
>> + gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>; /* PH23 */
>> + };
>> +
>> +};
>> +
>> +&ahci {
>> + target-supply = <®_ahci_5v>;
>> + status = "okay";
>> +};
>> +
>> +&cpu0 {
>> + cpu-supply = <®_dcdc2>;
>> +};
>> +
>> +&ehci0 {
>> + status = "okay";
>> +};
>> +
>> +&ehci1 {
>> + status = "okay";
>> +};
>> +
>> +&ohci0 {
>> + status = "okay";
>> +};
>> +
>> +&ohci1 {
>> + status = "okay";
>> +};
>> +
>> +&gmac {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&gmac_pins_rgmii_a>;
>> + phy = <&phy1>;
>> + phy-mode = "rgmii";
>> + phy-supply = <®_gmac_3v3>;
>> + status = "okay";
>> +
>> + fixed-link {
>> + speed = <1000>;
>> + full-duplex;
>> + };
>> +
>> + mdio {
>> + compatible = "snps,dwmac-mdio";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + switch: ethernet-switch at 1e {
>> + compatible = "brcm,bcm53125";
>> + reg = <30>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + ports {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + port0: port at 0 {
>> + reg = <0>;
>> + label = "lan2";
>> + };
>> +
>> + port1: port at 1 {
>> + reg = <1>;
>> + label = "lan3";
>> + };
>> +
>> + port2: port at 2 {
>> + reg = <2>;
>> + label = "lan4";
>> + };
>> +
>> + port3: port at 3 {
>> + reg = <3>;
>> + label = "wan";
>> + };
>> +
>> + port4: port at 4 {
>> + reg = <4>;
>> + label = "lan1";
>> + };
>> +
>> + port8: port at 8 {
>> + reg = <8>;
>> + label = "cpu";
>> + ethernet = <&gmac>;
>> + phy-mode = "rgmii";
>> + fixed-link {
>> + speed = <1000>;
>> + full-duplex;
>> + };
>> + };
>> + };
>> + };
>> + };
>> +};
>> +
>> +&i2c0 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&i2c0_pins_a>;
>> + status = "okay";
>> +
>> + axp209: pmic at 34 {
>> + compatible = "x-powers,axp209";
>> + reg = <0x34>;
>> + interrupt-parent = <&nmi_intc>;
>> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
>> +
>> + interrupt-controller;
>> + #interrupt-cells = <1>;
>> + };
>> +};
>> +
>> +#include "axp209.dtsi"
>> +
>> +&i2c2 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&i2c2_pins_a>;
>> + status = "okay";
>> +};
>> +
>> +&ir0 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&ir0_rx_pins_a>;
>> + status = "okay";
>> +};
>> +
>> +&mmc0 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bpi_r1>;
>> + vmmc-supply = <®_vcc3v3>;
>> + bus-width = <4>;
>> + cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
>> + cd-inverted;
>> + status = "okay";
>> +};
>> +
>> +&otg_sram {
>> + status = "okay";
>> +};
>> +
>> +&pio {
>> + usb0_id_detect_pin: usb0_id_detect_pin at 0 {
>> + allwinner,pins = "PH4";
>> + allwinner,function = "gpio_in";
>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> + };
>> +
>> + usb0_vbus_detect_pin: usb0_vbus_detect_pin at 0 {
>> + allwinner,pins = "PH5";
>> + allwinner,function = "gpio_in";
>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> + };
>> +
>> + usb0_vbus_pin_bpi_r1: usb0_vbus_pin at 0 {
>> + allwinner,pins = "PB9";
>> + allwinner,function = "gpio_out";
>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> + };
>> +
>> + usb2_vbus_pin_bpi_r1: usb2_vbus_pin at 0 {
>> + allwinner,pins = "PH3";
>> + allwinner,function = "gpio_out";
>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> + };
>> +
>> + mmc0_cd_pin_bpi_r1: mmc0_cd_pin at 0 {
>> + allwinner,pins = "PH1";
>> + allwinner,function = "gpio_in";
>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
>> + };
>> +
>> + gmac_power_pin_bpi_r1: gmac_power_pin at 0 {
>> + allwinner,pins = "PH23";
>> + allwinner,function = "gpio_out";
>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> + };
>> +
>> + led_pins_bpi_r1: led_pins at 0 {
>> + allwinner,pins = "PH24";
>> + allwinner,function = "gpio_out";
>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> + };
>> +};
>> +
>> +®_ahci_5v {
>> + status = "okay";
>> +};
>> +
>> +®_dcdc2 {
>> + regulator-always-on;
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1400000>;
>> + regulator-name = "vdd-cpu";
>> +};
>> +
>> +®_dcdc3 {
>> + regulator-always-on;
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1400000>;
>> + regulator-name = "vdd-int-dll";
>> +};
>> +
>> +®_ldo1 {
>> + regulator-name = "vdd-rtc";
>> +};
>> +
>> +®_ldo2 {
>> + regulator-always-on;
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <3000000>;
>> + regulator-name = "avcc";
>> +};
>> +
>> +®_usb0_vbus {
>> + pinctrl-0 = <&usb0_vbus_pin_bpi_r1>;
>> + gpio = <&pio 1 9 GPIO_ACTIVE_HIGH>; /* PB9 */
>> + status = "okay";
>> +};
>> +
>> +®_usb1_vbus {
>> + status = "okay";
>> +};
>> +
>> +®_usb2_vbus {
>> + pinctrl-0 = <&usb2_vbus_pin_bpi_r1>;
>> + gpio = <&pio 7 3 GPIO_ACTIVE_HIGH>; /* PH3 */
>> + status = "okay";
>> +};
>> +
>> +&spi0 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&spi0_pins_a>,
>> + <&spi0_cs0_pins_a>,
>> + <&spi0_cs1_pins_a>;
>> + status = "okay";
>> +};
>> +
>> +&uart0 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&uart0_pins_a>;
>> + status = "okay";
>> +};
>> +
>> +&uart2 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&uart2_pins_a>;
>> + status = "okay";
>> +};
>> +
>> +&uart3 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&uart3_pins_b>;
>> + status = "okay";
>> +};
>> +
>> +&uart7 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&uart7_pins_a>;
>> + status = "okay";
>> +};
>> +
>> +&usb_otg {
>> + dr_mode = "otg";
>> + status = "okay";
>> +};
>> +
>> +&usb_power_supply {
>> + status = "okay";
>> +};
>> +
>> +&usbphy {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&usb0_id_detect_pin>;
>> + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
>> + usb0_vbus_power-supply = <&usb_power_supply>;
>> + usb0_vbus-supply = <®_usb0_vbus>;
>> + usb1_vbus-supply = <®_usb1_vbus>;
>> + usb2_vbus-supply = <®_usb2_vbus>;
>> + status = "okay";
>> +};
>> --
>> 2.9.3
>>
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2016-10-03 20:21 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2016-10-03 20:01 [U-Boot] [PATCH 1/2] [PATCH 1/2] ARM: sun7i: config: add config for Sinovoip/Bananapi BPI-R1 Stephen Arnold
2016-10-03 20:01 ` [U-Boot] [PATCH 2/2] [PATCH 2/2] ARM: sun7i: dts: add support " Stephen Arnold
2016-10-03 20:01 ` [U-Boot] [PATCH] " Stephen Arnold
2016-10-03 20:19 ` Stephen Arnold
2016-10-03 20:21 ` Stephen Arnold
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox