From: Stefan Roese <sr@denx.de>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 14/15] arm64: mvebu: Add PCI support to DB-88F8040 board
Date: Tue, 15 Nov 2016 10:08:30 +0100 [thread overview]
Message-ID: <20161115090831.8426-14-sr@denx.de> (raw)
In-Reply-To: <20161115090831.8426-1-sr@denx.de>
This patch adds PCI support to the Marvell Armada-8K devel board.
Additionally the Intel E1000 ethernet driver is enabled so that
network support is available on this board, even without the
internal network interfaces being supported (yet).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
---
configs/mvebu_db-88f8040_defconfig | 3 +++
include/configs/mvebu_armada-8k.h | 8 ++++++++
2 files changed, 11 insertions(+)
diff --git a/configs/mvebu_db-88f8040_defconfig b/configs/mvebu_db-88f8040_defconfig
index eccb0f0..61d58b5 100644
--- a/configs/mvebu_db-88f8040_defconfig
+++ b/configs/mvebu_db-88f8040_defconfig
@@ -36,6 +36,9 @@ CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PHYLIB=y
+CONFIG_PCI=y
+CONFIG_DM_PCI=y
+CONFIG_PCIE_DW_MVEBU=y
CONFIG_MVEBU_COMPHY_SUPPORT=y
# CONFIG_SPL_SERIAL_PRESENT is not set
CONFIG_DEBUG_UART=y
diff --git a/include/configs/mvebu_armada-8k.h b/include/configs/mvebu_armada-8k.h
index 3b35cb3..8ab5bbe 100644
--- a/include/configs/mvebu_armada-8k.h
+++ b/include/configs/mvebu_armada-8k.h
@@ -128,4 +128,12 @@
#define CONFIG_CMD_PART
#define CONFIG_PARTITION_UUIDS
+/*
+ * PCI configuration
+ */
+#ifdef CONFIG_PCIE_DW_MVEBU
+#define CONFIG_E1000
+#define CONFIG_CMD_PCI
+#endif
+
#endif /* _CONFIG_MVEBU_ARMADA_8K_H */
--
2.10.2
next prev parent reply other threads:[~2016-11-15 9:08 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-11-15 9:08 [U-Boot] [PATCH 01/15] arm64: mvebu: Rename db-88f7040 files to armada-8k Stefan Roese
2016-11-15 9:08 ` [U-Boot] [PATCH 02/15] arm64: mvebu: Add Armada-80x0 dts/dtsi files Stefan Roese
2016-11-15 9:08 ` [U-Boot] [PATCH 03/15] arm64: mvebu: armada-8k: Only configure xHCI power on DB-88F7040 board Stefan Roese
2016-11-15 9:08 ` [U-Boot] [PATCH 04/15] arm64: mvebu: Add slave CP area to the memory map Stefan Roese
2016-11-15 9:08 ` [U-Boot] [PATCH 05/15] arm64: mvebu: Add support for the DB-88F8040 Armada 8k devel board Stefan Roese
2016-11-15 9:08 ` [U-Boot] [PATCH 06/15] arm64: mvebu: armada-cp110-master.dtsi: Rename comphy DT node names Stefan Roese
2016-11-15 9:08 ` [U-Boot] [PATCH 07/15] arm64: mvebu: armada-cp110-slave.dtsi: Add COMPHY / UTMI device tree nodes Stefan Roese
2016-11-15 9:08 ` [U-Boot] [PATCH 08/15] arm64: mvebu: armada-8040-db.dts: Add COMPHY configuration Stefan Roese
2016-11-15 9:08 ` [U-Boot] [PATCH 09/15] arm64: mvebu: armada-8040-db.dts: Add I2C and SPI aliases Stefan Roese
2016-11-15 9:08 ` [U-Boot] [PATCH 10/15] arm64: mvebu: Init COMPHY from the slave-CP on the A8k Stefan Roese
2016-11-15 9:08 ` [U-Boot] [PATCH 11/15] drivers/phy: marvell: Add support for the slave CP COMPHY device Stefan Roese
2016-11-15 9:08 ` [U-Boot] [PATCH 12/15] pci: mvebu: Add PCIe driver for Armada-8K Stefan Roese
2016-11-18 1:14 ` Simon Glass
2016-11-25 13:56 ` Stefan Roese
2016-11-28 12:38 ` [U-Boot] [PATCH 12/15 v2] " Stefan Roese
2016-12-03 4:26 ` Simon Glass
2016-12-03 9:20 ` Stefan Roese
2016-12-03 18:31 ` Simon Glass
2016-12-05 12:23 ` Stefan Roese
2016-11-15 9:08 ` [U-Boot] [PATCH 13/15] arm64: mvebu: Add regions for PCI spaces to the memory map Stefan Roese
2016-11-15 9:08 ` Stefan Roese [this message]
2016-11-15 9:08 ` [U-Boot] [PATCH 15/15] arm64: mvebu: Restrict memory size to a usable maximum Stefan Roese
2016-12-05 12:56 ` [U-Boot] [PATCH 01/15] arm64: mvebu: Rename db-88f7040 files to armada-8k Stefan Roese
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20161115090831.8426-14-sr@denx.de \
--to=sr@denx.de \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox