public inbox for u-boot@lists.denx.de
 help / color / mirror / Atom feed
From: Jason Rush <jarush@gmail.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH v5 5/5] dts: cadence_spi: Update documentation for DT bindings
Date: Sat,  6 Jan 2018 12:18:02 -0600	[thread overview]
Message-ID: <20180106181802.9298-6-jarush@gmail.com> (raw)
In-Reply-To: <20180106181802.9298-1-jarush@gmail.com>

Update documentation to reflect adopting the Linux DT bindings.

Tested on TI K2G platform:
Tested-by: Vignesh R <vigneshr@ti.com>

Tested on a socfpga-cyclonev board:
Tested-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>

Signed-off-by: Jason Rush <jarush@gmail.com>
Cc: Marek Vasut <marex@denx.de>
---
Changes for v5:
   - Rebased
Changes for v4:
   - Updated documentation

 doc/device-tree-bindings/spi/spi-cadence.txt | 13 ++++++++-----
 1 file changed, 8 insertions(+), 5 deletions(-)

diff --git a/doc/device-tree-bindings/spi/spi-cadence.txt b/doc/device-tree-bindings/spi/spi-cadence.txt
index c1e2233d7c..74c82080fc 100644
--- a/doc/device-tree-bindings/spi/spi-cadence.txt
+++ b/doc/device-tree-bindings/spi/spi-cadence.txt
@@ -6,7 +6,10 @@ Required properties:
 - reg			: 1.Physical base address and size of SPI registers map.
 			  2. Physical base address & size of NOR Flash.
 - clocks		: Clock phandles (see clock bindings for details).
-- sram-size		: spi controller sram size.
+- cdns,fifo-depth	: Size of the data FIFO in words.
+- cdns,fifo-width	: Bus width of the data FIFO in bytes.
+- cdns,trigger-address	: 32-bit indirect AHB trigger address.
+- cdns,is-decoded-cs	: Flag to indicate whether decoder is used or not.
 - status		: enable in requried dts.
 
 connected flash properties
@@ -15,14 +18,14 @@ connected flash properties
 - spi-max-frequency	: Max supported spi frequency.
 - page-size		: Flash page size.
 - block-size		: Flash memory block size.
-- tshsl-ns		: Added delay in master reference clocks (ref_clk) for
+- cdns,tshsl-ns		: Added delay in master reference clocks (ref_clk) for
 			  the length that the master mode chip select outputs
 			  are de-asserted between transactions.
-- tsd2d-ns		: Delay in master reference clocks (ref_clk) between one
+- cdns,tsd2d-ns		: Delay in master reference clocks (ref_clk) between one
 			  chip select being de-activated and the activation of
 			  another.
-- tchsh-ns		: Delay in master reference clocks between last bit of
+- cdns,tchsh-ns		: Delay in master reference clocks between last bit of
 			  current transaction and de-asserting the device chip
 			  select (n_ss_out).
-- tslch-ns		: Delay in master reference clocks between setting
+- cdns,tslch-ns		: Delay in master reference clocks between setting
 			  n_ss_out low and first bit transfer
-- 
2.11.0

  parent reply	other threads:[~2018-01-06 18:18 UTC|newest]

Thread overview: 18+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-01-06 18:17 [U-Boot] [PATCH v5 0/5] spi: cadence_spi: Adopt Linux DT bindings Jason Rush
2018-01-06 18:17 ` [U-Boot] [PATCH v5 1/5] spi: cadence_spi: Sync DT bindings with Linux Jason Rush
2018-01-23  9:12   ` Jagan Teki
2018-01-06 18:17 ` [U-Boot] [PATCH v5 2/5] dts: " Jason Rush
2018-01-23  9:16   ` Jagan Teki
2018-01-23 14:15     ` Jason Rush
2018-01-23 14:25       ` Jagan Teki
2018-01-23 15:12         ` Jason Rush
2018-01-23 16:21           ` Jagan Teki
2018-01-06 18:18 ` [U-Boot] [PATCH v5 3/5] config: cadence_spi: Remove defines read from DT Jason Rush
2018-01-23  9:15   ` Jagan Teki
2018-01-06 18:18 ` [U-Boot] [PATCH v5 4/5] dts: k2g: Clean-up indentation Jason Rush
2018-01-23  9:17   ` Jagan Teki
2018-01-06 18:18 ` Jason Rush [this message]
2018-01-23  9:19   ` [U-Boot] [PATCH v5 5/5] dts: cadence_spi: Update documentation for DT bindings Jagan Teki
2018-01-07 11:41 ` [U-Boot] [PATCH v5 0/5] spi: cadence_spi: Adopt Linux " Marek Vasut
2018-01-15 12:03   ` Simon Goldschmidt
2018-01-23  8:13     ` Simon Goldschmidt

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20180106181802.9298-6-jarush@gmail.com \
    --to=jarush@gmail.com \
    --cc=u-boot@lists.denx.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox