* [U-Boot] [PATCH 0/4] mips: bmips: add HSSPI support
@ 2017-05-23 19:18 Álvaro Fernández Rojas
2017-05-23 19:18 ` [U-Boot] [PATCH 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
` (8 more replies)
0 siblings, 9 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-05-23 19:18 UTC (permalink / raw)
To: u-boot
BCM63xx HSSPI controller has the same issue as BCM63xx SPI controller: it
doesn't allow keeping CS active between transfers.
However, this controller allows changing CS polarities, which is used in the
linux upstream driver to manage CS as desired.
Álvaro Fernández Rojas (4):
dm: spi: add BCM63xx HSSPI driver
mips: bmips: add bcm63xx-hsspi driver support for BCM6328
mips: bmips: add bcm63xx-hsspi driver support for BCM63268
mips: bmips: enable the SPI flash on the Comtrend AR-5387un
arch/mips/dts/brcm,bcm63268.dtsi | 21 ++
arch/mips/dts/brcm,bcm6328.dtsi | 24 ++
arch/mips/dts/comtrend,ar-5387un.dts | 12 +
configs/comtrend_ar5387un_ram_defconfig | 8 +
drivers/spi/Kconfig | 8 +
drivers/spi/Makefile | 1 +
drivers/spi/bcm63xx_hsspi.c | 392 ++++++++++++++++++++++++++++++++
7 files changed, 466 insertions(+)
create mode 100644 drivers/spi/bcm63xx_hsspi.c
--
2.1.4
^ permalink raw reply [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH 1/4] dm: spi: add BCM63xx HSSPI driver
2017-05-23 19:18 [U-Boot] [PATCH 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
@ 2017-05-23 19:18 ` Álvaro Fernández Rojas
2017-06-01 3:10 ` Simon Glass
2017-05-23 19:18 ` [U-Boot] [PATCH 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328 Álvaro Fernández Rojas
` (7 subsequent siblings)
8 siblings, 1 reply; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-05-23 19:18 UTC (permalink / raw)
To: u-boot
This driver is a simplified version of linux/drivers/spi/spi-bcm63xx-hsspi.c
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
---
drivers/spi/Kconfig | 8 +
drivers/spi/Makefile | 1 +
drivers/spi/bcm63xx_hsspi.c | 392 ++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 401 insertions(+)
create mode 100644 drivers/spi/bcm63xx_hsspi.c
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index e452223..a67c05f 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -40,6 +40,14 @@ config ATMEL_SPI
many AT32 (AVR32) and AT91 (ARM) chips. This driver can be
used to access the SPI Flash, such as AT25DF321.
+config BCM6328_HSSPI
+ bool "BCM6328 HSSPI driver"
+ depends on ARCH_BMIPS
+ help
+ Enable the BCM6328 HSSPI driver. This driver can be used to
+ access the SPI NOR flash on platforms embedding this Broadcom
+ SPI core.
+
choice
prompt "BCM63xx SPI driver"
depends on ARCH_BMIPS
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index c9ba648..a12a354 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -19,6 +19,7 @@ obj-$(CONFIG_ALTERA_SPI) += altera_spi.o
obj-$(CONFIG_ATH79_SPI) += ath79_spi.o
obj-$(CONFIG_ATMEL_DATAFLASH_SPI) += atmel_dataflash_spi.o
obj-$(CONFIG_ATMEL_SPI) += atmel_spi.o
+obj-$(CONFIG_BCM6328_HSSPI) += bcm63xx_hsspi.o
obj-$(CONFIG_BCM6338_SPI)$(CONFIG_BCM6358_SPI) += bcm63xx_spi.o
obj-$(CONFIG_CADENCE_QSPI) += cadence_qspi.o cadence_qspi_apb.o
obj-$(CONFIG_CF_SPI) += cf_spi.o
diff --git a/drivers/spi/bcm63xx_hsspi.c b/drivers/spi/bcm63xx_hsspi.c
new file mode 100644
index 0000000..bdd2e3e
--- /dev/null
+++ b/drivers/spi/bcm63xx_hsspi.c
@@ -0,0 +1,392 @@
+/*
+ * Copyright (C) 2017 Álvaro Fernández Rojas <noltari@gmail.com>
+ *
+ * Derived from linux/drivers/spi/spi-bcm63xx-hsspi.c:
+ * Copyright (C) 2000-2010 Broadcom Corporation
+ * Copyright (C) 2012-2013 Jonas Gorski <jogo@openwrt.org>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <clk.h>
+#include <dm.h>
+#include <spi.h>
+#include <reset.h>
+#include <asm/io.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define SPI_PP_SEL 0
+
+#define SPI_MAX_SYNC_CLOCK 30000000
+
+/* SPI Control register */
+#define SPI_CTL_REG 0x000
+#define SPI_CTL_CS_POL_SHIFT 0
+#define SPI_CTL_CS_POL_MASK (0xff << SPI_CTL_CS_POL_SHIFT)
+#define SPI_CTL_CLK_GATE_SHIFT 16
+#define SPI_CTL_CLK_GATE_MASK (1 << SPI_CTL_CLK_GATE_SHIFT)
+#define SPI_CTL_CLK_POL_SHIFT 17
+#define SPI_CTL_CLK_POL_MASK (1 << SPI_CTL_CLK_POL_SHIFT)
+
+/* SPI Interrupts registers */
+#define SPI_IR_STAT_REG 0x008
+#define SPI_IR_ST_MASK_REG 0x00c
+#define SPI_IR_MASK_REG 0x010
+
+#define SPI_IR_CLEAR_ALL 0xff001f1f
+
+/* SPI Ping-Pong Command registers */
+#define SPI_PP_CMD_REG (0x080 + (0x40 * (SPI_PP_SEL)) + 0x00)
+#define SPI_PP_CMD_OP_SHIFT 0
+#define SPI_PP_CMD_OP_START (0x1 << SPI_PP_CMD_OP_SHIFT)
+#define SPI_PP_CMD_PFL_SHIFT 8
+#define SPI_PP_CMD_PFL_MASK (0x7 << SPI_PP_CMD_PFL_SHIFT)
+#define SPI_PP_CMD_SLAVE_SHIFT 12
+#define SPI_PP_CMD_SLAVE_MASK (0x7 << SPI_PP_CMD_SLAVE_SHIFT)
+
+/* SPI Ping-Pong Status registers */
+#define SPI_PP_STAT_REG (0x080 + (0x40 * (SPI_PP_SEL)) + 0x04)
+#define SPI_PP_STAT_SRCBUSY_SHIFT 1
+#define SPI_PP_STAT_SRCBUSY_MASK (1 << SPI_PP_STAT_SRCBUSY_SHIFT)
+
+/* SPI Profile Clock registers */
+#define SPI_PFL_CLK_REG(x) (0x100 + (0x20 * (x)) + 0x00)
+#define SPI_PFL_CLK_FREQ_SHIFT 0
+#define SPI_PFL_CLK_FREQ_MASK (0x3fff << SPI_PFL_CLK_FREQ_SHIFT)
+#define SPI_PFL_CLK_RSTLOOP_SHIFT 15
+#define SPI_PFL_CLK_RSTLOOP_MASK (1 << SPI_PFL_CLK_RSTLOOP_SHIFT)
+
+/* SPI Profile Signal registers */
+#define SPI_PFL_SIG_REG(x) (0x100 + (0x20 * (x)) + 0x04)
+#define SPI_PFL_SIG_LATCHRIS_SHIFT 12
+#define SPI_PFL_SIG_LATCHRIS_MASK (1 << SPI_PFL_SIG_LATCHRIS_SHIFT)
+#define SPI_PFL_SIG_LAUNCHRIS_SHIFT 13
+#define SPI_PFL_SIG_LAUNCHRIS_MASK (1 << SPI_PFL_SIG_LAUNCHRIS_SHIFT)
+#define SPI_PFL_SIG_ASYNCIN_SHIFT 16
+#define SPI_PFL_SIG_ASYNCIN_MASK (1 << SPI_PFL_SIG_ASYNCIN_SHIFT)
+
+/* SPI Profile Mode registers */
+#define SPI_PFL_MODE_REG(x) (0x100 + (0x20 * (x)) + 0x08)
+#define SPI_PFL_MODE_FILL_SHIFT 0
+#define SPI_PFL_MODE_FILL_MASK (0xff << SPI_PFL_MODE_FILL_SHIFT)
+#define SPI_PFL_MODE_MDRDSZ_SHIFT 16
+#define SPI_PFL_MODE_MDRDSZ_MASK (1 << SPI_PFL_MODE_MDRDSZ_SHIFT)
+#define SPI_PFL_MODE_MDWRSZ_SHIFT 18
+#define SPI_PFL_MODE_MDWRSZ_MASK (1 << SPI_PFL_MODE_MDWRSZ_SHIFT)
+#define SPI_PFL_MODE_3WIRE_SHIFT 20
+#define SPI_PFL_MODE_3WIRE_MASK (1 << SPI_PFL_MODE_3WIRE_SHIFT)
+
+/* SPI Ping-Pong FIFO registers */
+#define SPI_PP_FIFO_SIZE 0x200
+#define SPI_PP_FIFO_BASE (0x200 + \
+ (SPI_PP_FIFO_SIZE * SPI_PP_SEL))
+
+/* SPI Ping-Pong FIFO OP register */
+#define SPI_PP_FIFO_OP_SIZE 0x2
+#define SPI_PP_FIFO_OP_REG (SPI_PP_FIFO_BASE + 0x00)
+#define SPI_PP_FIFO_OP_BYTES_SHIFT 0
+#define SPI_PP_FIFO_OP_BYTES_MASK (0x3ff << SPI_PP_FIFO_OP_BYTES_SHIFT)
+#define SPI_PP_FIFO_OP_MBIT_SHIFT 11
+#define SPI_PP_FIFO_OP_MBIT_MASK (1 << SPI_PP_FIFO_OP_MBIT_SHIFT)
+#define SPI_PP_FIFO_OP_CODE_SHIFT 13
+#define SPI_PP_FIFO_OP_CODE_RW (1 << SPI_PP_FIFO_OP_CODE_SHIFT)
+#define SPI_PP_FIFO_OP_CODE_W (2 << SPI_PP_FIFO_OP_CODE_SHIFT)
+#define SPI_PP_FIFO_OP_CODE_R (3 << SPI_PP_FIFO_OP_CODE_SHIFT)
+
+struct bcm63xx_hsspi_priv {
+ void __iomem *regs;
+ ulong clk_rate;
+ uint8_t num_cs;
+ uint8_t cs_pols;
+ uint speed;
+};
+
+static int bcm63xx_hsspi_cs_info(struct udevice *bus, uint cs,
+ struct spi_cs_info *info)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(bus);
+
+ if (cs >= priv->num_cs) {
+ error("no cs %u\n", cs);
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int bcm63xx_hsspi_set_mode(struct udevice *bus, uint mode)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(bus);
+
+ /* clock polarity */
+ if (mode & SPI_CPOL)
+ setbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CLK_POL_MASK);
+ else
+ clrbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CLK_POL_MASK);
+
+ return 0;
+}
+
+static int bcm63xx_hsspi_set_speed(struct udevice *bus, uint speed)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(bus);
+
+ priv->speed = speed;
+
+ return 0;
+}
+
+/*
+ * BCM63xx HSSPI driver doesn't allow keeping CS active between transfers
+ * because they are controlled by HW.
+ * However, it provides a mechanism to prepend write transfers prior to read
+ * transfers (with a maximum prepend of 15 bytes), which is usually enough for
+ * SPI-connected flashes since reading requires prepending a write transfer of
+ * 5 bytes. On the other hand it also provides a way to invert each CS
+ * polarity, not only between transfers like the older BCM63xx SPI driver, but
+ * also the rest of the time.
+ *
+ * Instead of using the prepend mechanism, this implementation inverts the
+ * polarity of both the desired CS and another dummy CS when the bus is
+ * claimed. This way, the dummy CS is restored to its inactive value when
+ * transfers are issued and the desired CS is preserved in its active value
+ * all the time. This hack is also used in the upstream linux driver and
+ * allows keeping CS active between trasnfers even if the HW doesn't give
+ * this possibility.
+ */
+static int bcm63xx_hsspi_xfer(struct udevice *dev, unsigned int bitlen,
+ const void *dout, void *din, unsigned long flags)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev->parent);
+ struct dm_spi_slave_platdata *plat = dev_get_parent_platdata(dev);
+ size_t data_bytes = bitlen / 8;
+ size_t step_size = SPI_PP_FIFO_SIZE;
+ uint16_t opcode = 0;
+ uint32_t val;
+ const uint8_t *tx = dout;
+ uint8_t *rx = din;
+
+ if (flags & SPI_XFER_BEGIN) {
+ uint32_t clr, set;
+
+ /* profile clock */
+ set = DIV_ROUND_UP(priv->clk_rate, priv->speed);
+ set = DIV_ROUND_UP(2048, set);
+ set &= SPI_PFL_CLK_FREQ_MASK;
+ set |= SPI_PFL_CLK_RSTLOOP_MASK;
+ writel_be(set, priv->regs + SPI_PFL_CLK_REG(plat->cs));
+
+ /* profile signal */
+ set = 0;
+ clr = SPI_PFL_SIG_LAUNCHRIS_MASK |
+ SPI_PFL_SIG_LATCHRIS_MASK |
+ SPI_PFL_SIG_ASYNCIN_MASK;
+
+ /* latch/launch config */
+ if (plat->mode & SPI_CPHA)
+ set |= SPI_PFL_SIG_LAUNCHRIS_MASK;
+ else
+ set |= SPI_PFL_SIG_LATCHRIS_MASK;
+
+ /* async clk */
+ if (priv->speed > SPI_MAX_SYNC_CLOCK)
+ set |= SPI_PFL_SIG_ASYNCIN_MASK;
+
+ clrsetbits_be32(priv->regs + SPI_PFL_SIG_REG(plat->cs),
+ clr, set);
+
+ /* global control */
+ set = 0;
+ clr = 0;
+
+ /* invert cs polarity */
+ if (priv->cs_pols & BIT(plat->cs))
+ clr |= BIT(plat->cs);
+ else
+ set |= BIT(plat->cs);
+
+ /* invert dummy cs polarity */
+ if (priv->cs_pols & BIT(!plat->cs))
+ clr |= BIT(!plat->cs);
+ else
+ set |= BIT(!plat->cs);
+
+ clrsetbits_be32(priv->regs + SPI_CTL_REG, clr, set);
+ }
+
+ /* fifo operation */
+ if (tx && rx)
+ opcode = SPI_PP_FIFO_OP_CODE_RW;
+ else if (rx)
+ opcode = SPI_PP_FIFO_OP_CODE_R;
+ else if (tx)
+ opcode = SPI_PP_FIFO_OP_CODE_W;
+
+ if (opcode != SPI_PP_FIFO_OP_CODE_R)
+ step_size -= SPI_PP_FIFO_OP_SIZE;
+
+ /* dual mode */
+ if ((opcode == SPI_PP_FIFO_OP_CODE_R && plat->mode == SPI_RX_DUAL) ||
+ (opcode == SPI_PP_FIFO_OP_CODE_W && plat->mode == SPI_TX_DUAL))
+ opcode |= SPI_PP_FIFO_OP_MBIT_MASK;
+
+ /* profile mode */
+ val = SPI_PFL_MODE_FILL_MASK |
+ SPI_PFL_MODE_MDRDSZ_MASK |
+ SPI_PFL_MODE_MDWRSZ_MASK;
+ if (plat->mode & SPI_3WIRE)
+ val |= SPI_PFL_MODE_3WIRE_MASK;
+ writel_be(val, priv->regs + SPI_PFL_MODE_REG(plat->cs));
+
+ /* transfer loop */
+ while (data_bytes > 0) {
+ size_t curr_step = min(step_size, data_bytes);
+
+ /* copy tx data */
+ if (tx) {
+ memcpy_toio(priv->regs + SPI_PP_FIFO_BASE +
+ SPI_PP_FIFO_OP_SIZE, tx, curr_step);
+ tx += curr_step;
+ }
+
+ /* set fifo operation */
+ writew_be(opcode | (curr_step & SPI_PP_FIFO_OP_BYTES_MASK),
+ priv->regs + SPI_PP_FIFO_OP_REG);
+
+ /* issue the transfer */
+ val = SPI_PP_CMD_OP_START;
+ val |= (plat->cs << SPI_PP_CMD_PFL_SHIFT) &
+ SPI_PP_CMD_PFL_MASK;
+ val |= (!plat->cs << SPI_PP_CMD_SLAVE_SHIFT) &
+ SPI_PP_CMD_SLAVE_MASK;
+ writel_be(val, priv->regs + SPI_PP_CMD_REG);
+
+ /* wait for completion */
+ do {
+ /* check ping-pong status */
+ val = readl_be(priv->regs + SPI_PP_STAT_REG);
+
+ /* transfer completed */
+ if (!(val & SPI_PP_STAT_SRCBUSY_MASK))
+ break;
+ } while (1);
+
+ /* copy rx data */
+ if (rx) {
+ memcpy_fromio(rx, priv->regs + SPI_PP_FIFO_BASE,
+ curr_step);
+ rx += curr_step;
+ }
+
+ data_bytes -= curr_step;
+ }
+
+ /* restore cs polarities */
+ if (flags & SPI_XFER_END)
+ clrsetbits_be32(priv->regs + SPI_CTL_REG,
+ SPI_CTL_CS_POL_MASK,
+ priv->cs_pols);
+
+ return 0;
+}
+
+static const struct dm_spi_ops bcm63xx_hsspi_ops = {
+ .cs_info = bcm63xx_hsspi_cs_info,
+ .set_mode = bcm63xx_hsspi_set_mode,
+ .set_speed = bcm63xx_hsspi_set_speed,
+ .xfer = bcm63xx_hsspi_xfer,
+};
+
+static const struct udevice_id bcm63xx_hsspi_ids[] = {
+ { .compatible = "brcm,bcm6328-hsspi", },
+ { /* sentinel */ }
+};
+
+static int bcm63xx_hsspi_child_pre_probe(struct udevice *dev)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev->parent);
+ struct dm_spi_slave_platdata *plat = dev_get_parent_platdata(dev);
+
+ /* check cs */
+ if (plat->cs >= priv->num_cs) {
+ error("no cs %u\n", plat->cs);
+ return -ENODEV;
+ }
+
+ /* cs polarity */
+ if (plat->mode & SPI_CS_HIGH)
+ priv->cs_pols |= BIT(plat->cs);
+ else
+ priv->cs_pols &= ~BIT(plat->cs);
+
+ return 0;
+}
+
+static int bcm63xx_hsspi_probe(struct udevice *dev)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev);
+ struct reset_ctl rst_ctl;
+ struct clk clk;
+ fdt_addr_t addr;
+ fdt_size_t size;
+ int ret;
+ uint32_t val;
+
+ addr = dev_get_addr_size_index(dev, 0, &size);
+ if (addr == FDT_ADDR_T_NONE)
+ return -EINVAL;
+
+ priv->regs = ioremap(addr, size);
+ priv->num_cs = fdtdec_get_uint(gd->fdt_blob, dev_of_offset(dev),
+ "num-cs", 8);
+
+ /* enable clock */
+ ret = clk_get_by_name(dev, "hsspi", &clk);
+ if (ret < 0)
+ return ret;
+ clk_enable(&clk);
+ clk_free(&clk);
+
+ /* get clock rate */
+ ret = clk_get_by_name(dev, "pll", &clk);
+ if (ret < 0)
+ return ret;
+ priv->clk_rate = clk_get_rate(&clk);
+ clk_free(&clk);
+
+ /* perform reset */
+ ret = reset_get_by_index(dev, 0, &rst_ctl);
+ if (ret < 0)
+ return ret;
+ reset_deassert(&rst_ctl);
+ reset_free(&rst_ctl);
+
+ /* initialize hardware */
+ writel_be(0, priv->regs + SPI_IR_MASK_REG);
+
+ /* clear pending interrupts */
+ writel_be(SPI_IR_CLEAR_ALL, priv->regs + SPI_IR_STAT_REG);
+
+ /* enable clk gate */
+ val = readl_be(priv->regs + SPI_CTL_REG);
+ val |= SPI_CTL_CLK_GATE_MASK;
+ writel_be(val, priv->regs + SPI_CTL_REG);
+
+ /* read default cs polarities */
+ priv->cs_pols = readl_be(priv->regs + SPI_CTL_REG) &
+ SPI_CTL_CS_POL_MASK;
+
+ return 0;
+}
+
+U_BOOT_DRIVER(bcm63xx_hsspi) = {
+ .name = "bcm63xx_hsspi",
+ .id = UCLASS_SPI,
+ .of_match = bcm63xx_hsspi_ids,
+ .ops = &bcm63xx_hsspi_ops,
+ .priv_auto_alloc_size = sizeof(struct bcm63xx_hsspi_priv),
+ .child_pre_probe = bcm63xx_hsspi_child_pre_probe,
+ .probe = bcm63xx_hsspi_probe,
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328
2017-05-23 19:18 [U-Boot] [PATCH 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
2017-05-23 19:18 ` [U-Boot] [PATCH 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
@ 2017-05-23 19:18 ` Álvaro Fernández Rojas
2017-06-01 3:10 ` Simon Glass
2017-05-23 19:18 ` [U-Boot] [PATCH 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268 Álvaro Fernández Rojas
` (6 subsequent siblings)
8 siblings, 1 reply; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-05-23 19:18 UTC (permalink / raw)
To: u-boot
This driver manages the SPI controller present on this SoC.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
---
arch/mips/dts/brcm,bcm6328.dtsi | 24 ++++++++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/arch/mips/dts/brcm,bcm6328.dtsi b/arch/mips/dts/brcm,bcm6328.dtsi
index a996075..67d9278 100644
--- a/arch/mips/dts/brcm,bcm6328.dtsi
+++ b/arch/mips/dts/brcm,bcm6328.dtsi
@@ -13,6 +13,10 @@
/ {
compatible = "brcm,bcm6328";
+ aliases {
+ spi0 = &spi;
+ };
+
cpus {
reg = <0x10000000 0x4>;
#address-cells = <1>;
@@ -40,6 +44,12 @@
#size-cells = <1>;
u-boot,dm-pre-reloc;
+ hsspi_pll: hsspi-pll {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <133333333>;
+ };
+
periph_osc: periph-osc {
compatible = "fixed-clock";
#clock-cells = <0>;
@@ -123,6 +133,20 @@
status = "disabled";
};
+ spi: spi at 10001000 {
+ compatible = "brcm,bcm6328-hsspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x10001000 0x600>;
+ clocks = <&periph_clk BCM6328_CLK_HSSPI>, <&hsspi_pll>;
+ clock-names = "hsspi", "pll";
+ resets = <&periph_rst BCM6328_RST_SPI>;
+ spi-max-frequency = <33333334>;
+ num-cs = <3>;
+
+ status = "disabled";
+ };
+
periph_pwr: power-controller at 10001848 {
compatible = "brcm,bcm6328-power-domain";
reg = <0x10001848 0x4>;
--
2.1.4
^ permalink raw reply related [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268
2017-05-23 19:18 [U-Boot] [PATCH 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
2017-05-23 19:18 ` [U-Boot] [PATCH 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
2017-05-23 19:18 ` [U-Boot] [PATCH 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328 Álvaro Fernández Rojas
@ 2017-05-23 19:18 ` Álvaro Fernández Rojas
2017-06-01 3:10 ` Simon Glass
2017-05-23 19:18 ` [U-Boot] [PATCH 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un Álvaro Fernández Rojas
` (5 subsequent siblings)
8 siblings, 1 reply; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-05-23 19:18 UTC (permalink / raw)
To: u-boot
This driver manages the high speed SPI controller present on this SoC.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
---
arch/mips/dts/brcm,bcm63268.dtsi | 21 +++++++++++++++++++++
1 file changed, 21 insertions(+)
diff --git a/arch/mips/dts/brcm,bcm63268.dtsi b/arch/mips/dts/brcm,bcm63268.dtsi
index 6e3d9c3..4d4e36c 100644
--- a/arch/mips/dts/brcm,bcm63268.dtsi
+++ b/arch/mips/dts/brcm,bcm63268.dtsi
@@ -15,6 +15,7 @@
aliases {
spi0 = &lsspi;
+ spi1 = &hsspi;
};
cpus {
@@ -44,6 +45,12 @@
#size-cells = <1>;
u-boot,dm-pre-reloc;
+ hsspi_pll: hsspi-pll {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <400000000>;
+ };
+
periph_osc: periph-osc {
compatible = "fixed-clock";
#clock-cells = <0>;
@@ -153,6 +160,20 @@
status = "disabled";
};
+ hsspi: spi at 10001000 {
+ compatible = "brcm,bcm6328-hsspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x10001000 0x600>;
+ clocks = <&periph_clk BCM63268_CLK_HSSPI>, <&hsspi_pll>;
+ clock-names = "hsspi", "pll";
+ resets = <&periph_rst BCM63268_RST_SPI>;
+ spi-max-frequency = <50000000>;
+ num-cs = <8>;
+
+ status = "disabled";
+ };
+
leds: led-controller at 10001900 {
compatible = "brcm,bcm6328-leds";
reg = <0x10001900 0x24>;
--
2.1.4
^ permalink raw reply related [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un
2017-05-23 19:18 [U-Boot] [PATCH 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
` (2 preceding siblings ...)
2017-05-23 19:18 ` [U-Boot] [PATCH 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268 Álvaro Fernández Rojas
@ 2017-05-23 19:18 ` Álvaro Fernández Rojas
2017-06-01 3:10 ` Simon Glass
2017-06-03 10:15 ` [U-Boot] [PATCH v2 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
` (4 subsequent siblings)
8 siblings, 1 reply; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-05-23 19:18 UTC (permalink / raw)
To: u-boot
It's a Macronix (mx25l12805d) 16 MB SPI flash.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
---
arch/mips/dts/comtrend,ar-5387un.dts | 12 ++++++++++++
configs/comtrend_ar5387un_ram_defconfig | 8 ++++++++
2 files changed, 20 insertions(+)
diff --git a/arch/mips/dts/comtrend,ar-5387un.dts b/arch/mips/dts/comtrend,ar-5387un.dts
index 73f2b49..6067881 100644
--- a/arch/mips/dts/comtrend,ar-5387un.dts
+++ b/arch/mips/dts/comtrend,ar-5387un.dts
@@ -51,6 +51,18 @@
};
};
+&spi {
+ status = "okay";
+
+ spi-flash at 0 {
+ compatible = "spi-flash";
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <33333334>;
+ };
+};
+
&uart0 {
u-boot,dm-pre-reloc;
status = "okay";
diff --git a/configs/comtrend_ar5387un_ram_defconfig b/configs/comtrend_ar5387un_ram_defconfig
index 5b05fd2..38c6a28 100644
--- a/configs/comtrend_ar5387un_ram_defconfig
+++ b/configs/comtrend_ar5387un_ram_defconfig
@@ -1,5 +1,6 @@
CONFIG_ARCH_BMIPS=y
CONFIG_BAUDRATE=115200
+CONFIG_BCM6328_HSSPI=y
CONFIG_BCM6328_POWER_DOMAIN=y
CONFIG_BCM6345_CLK=y
CONFIG_BCM6345_SERIAL=y
@@ -27,6 +28,8 @@ CONFIG_CMD_MEMINFO=y
# CONFIG_CMD_NET is not set
# CONFIG_CMD_NFS is not set
# CONFIG_CMD_SAVEENV is not set
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
# CONFIG_CMD_XIMG is not set
CONFIG_DEFAULT_DEVICE_TREE="comtrend,ar-5387un"
CONFIG_DISPLAY_CPUINFO=y
@@ -34,6 +37,8 @@ CONFIG_DISPLAY_CPUINFO=y
CONFIG_DM_GPIO=y
CONFIG_DM_RESET=y
CONFIG_DM_SERIAL=y
+CONFIG_DM_SPI=y
+CONFIG_DM_SPI_FLASH=y
CONFIG_HUSH_PARSER=y
CONFIG_LED=y
CONFIG_LED_BCM6328=y
@@ -47,6 +52,9 @@ CONFIG_POWER_DOMAIN=y
CONFIG_RESET=y
CONFIG_RESET_BCM6345=y
CONFIG_SOC_BMIPS_BCM6328=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_MTD=y
+CONFIG_SPI_FLASH_MACRONIX=y
# CONFIG_SPL_SERIAL_PRESENT is not set
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SYS_NO_FLASH=y
--
2.1.4
^ permalink raw reply related [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH 1/4] dm: spi: add BCM63xx HSSPI driver
2017-05-23 19:18 ` [U-Boot] [PATCH 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
@ 2017-06-01 3:10 ` Simon Glass
0 siblings, 0 replies; 45+ messages in thread
From: Simon Glass @ 2017-06-01 3:10 UTC (permalink / raw)
To: u-boot
Hi Alvaro,
On 23 May 2017 at 13:18, Álvaro Fernández Rojas <noltari@gmail.com> wrote:
> This driver is a simplified version of linux/drivers/spi/spi-bcm63xx-hsspi.c
>
> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
> ---
> drivers/spi/Kconfig | 8 +
> drivers/spi/Makefile | 1 +
> drivers/spi/bcm63xx_hsspi.c | 392 ++++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 401 insertions(+)
> create mode 100644 drivers/spi/bcm63xx_hsspi.c
Reviewed-by: Simon Glass <sjg@chromium.org>
Suggest you add error checking to clk_enable(), etc. and split
bcm63xx_hsspi_xfer() into a few subparts as it is very long.
Regards,
Simon
^ permalink raw reply [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328
2017-05-23 19:18 ` [U-Boot] [PATCH 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328 Álvaro Fernández Rojas
@ 2017-06-01 3:10 ` Simon Glass
0 siblings, 0 replies; 45+ messages in thread
From: Simon Glass @ 2017-06-01 3:10 UTC (permalink / raw)
To: u-boot
On 23 May 2017 at 13:18, Álvaro Fernández Rojas <noltari@gmail.com> wrote:
> This driver manages the SPI controller present on this SoC.
>
> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
> ---
> arch/mips/dts/brcm,bcm6328.dtsi | 24 ++++++++++++++++++++++++
> 1 file changed, 24 insertions(+)
Reviewed-by: Simon Glass <sjg@chromium.org>
^ permalink raw reply [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268
2017-05-23 19:18 ` [U-Boot] [PATCH 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268 Álvaro Fernández Rojas
@ 2017-06-01 3:10 ` Simon Glass
0 siblings, 0 replies; 45+ messages in thread
From: Simon Glass @ 2017-06-01 3:10 UTC (permalink / raw)
To: u-boot
On 23 May 2017 at 13:18, Álvaro Fernández Rojas <noltari@gmail.com> wrote:
> This driver manages the high speed SPI controller present on this SoC.
>
> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
> ---
> arch/mips/dts/brcm,bcm63268.dtsi | 21 +++++++++++++++++++++
> 1 file changed, 21 insertions(+)
>
Reviewed-by: Simon Glass <sjg@chromium.org>
^ permalink raw reply [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un
2017-05-23 19:18 ` [U-Boot] [PATCH 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un Álvaro Fernández Rojas
@ 2017-06-01 3:10 ` Simon Glass
0 siblings, 0 replies; 45+ messages in thread
From: Simon Glass @ 2017-06-01 3:10 UTC (permalink / raw)
To: u-boot
On 23 May 2017 at 13:18, Álvaro Fernández Rojas <noltari@gmail.com> wrote:
> It's a Macronix (mx25l12805d) 16 MB SPI flash.
>
> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
> ---
> arch/mips/dts/comtrend,ar-5387un.dts | 12 ++++++++++++
> configs/comtrend_ar5387un_ram_defconfig | 8 ++++++++
> 2 files changed, 20 insertions(+)
Reviewed-by: Simon Glass <sjg@chromium.org>
^ permalink raw reply [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v2 0/4] mips: bmips: add HSSPI support
2017-05-23 19:18 [U-Boot] [PATCH 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
` (3 preceding siblings ...)
2017-05-23 19:18 ` [U-Boot] [PATCH 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un Álvaro Fernández Rojas
@ 2017-06-03 10:15 ` Álvaro Fernández Rojas
2017-06-03 10:16 ` [U-Boot] [PATCH v2 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
` (3 more replies)
2017-06-14 9:59 ` [U-Boot] [PATCH v3 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
` (3 subsequent siblings)
8 siblings, 4 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-06-03 10:15 UTC (permalink / raw)
To: u-boot
BCM63xx HSSPI controller has the same issue as BCM63xx SPI controller: it
doesn't allow keeping CS active between transfers.
However, this controller allows changing CS polarities, which is used in the
linux upstream driver to manage CS as desired.
v2: Introduce changes suggested by Simon Glass:
- Split bcm63xx_hsspi_xfer() into smaller functions.
- Check possible clock errors.
- Check possible reset errors.
- Switch to devfdt_get_addr_size_index().
- Use setbits32_be() for clock gate.
Álvaro Fernández Rojas (4):
dm: spi: add BCM63xx HSSPI driver
mips: bmips: add bcm63xx-hsspi driver support for BCM6328
mips: bmips: add bcm63xx-hsspi driver support for BCM63268
mips: bmips: enable the SPI flash on the Comtrend AR-5387un
arch/mips/dts/brcm,bcm63268.dtsi | 21 ++
arch/mips/dts/brcm,bcm6328.dtsi | 24 ++
arch/mips/dts/comtrend,ar-5387un.dts | 12 +
configs/comtrend_ar5387un_ram_defconfig | 8 +
drivers/spi/Kconfig | 8 +
drivers/spi/Makefile | 1 +
drivers/spi/bcm63xx_hsspi.c | 413 ++++++++++++++++++++++++++++++++
7 files changed, 487 insertions(+)
create mode 100644 drivers/spi/bcm63xx_hsspi.c
--
2.1.4
^ permalink raw reply [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v2 1/4] dm: spi: add BCM63xx HSSPI driver
2017-06-03 10:15 ` [U-Boot] [PATCH v2 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
@ 2017-06-03 10:16 ` Álvaro Fernández Rojas
2017-06-04 9:02 ` Daniel Schwierzeck
2017-06-03 10:16 ` [U-Boot] [PATCH v2 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328 Álvaro Fernández Rojas
` (2 subsequent siblings)
3 siblings, 1 reply; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-06-03 10:16 UTC (permalink / raw)
To: u-boot
This driver is a simplified version of linux/drivers/spi/spi-bcm63xx-hsspi.c
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
---
v2: Introduce changes suggested by Simon Glass:
- Split bcm63xx_hsspi_xfer() into smaller functions.
- Check possible clock errors.
- Check possible reset errors.
- Switch to devfdt_get_addr_size_index().
- Use setbits32_be() for clock gate.
drivers/spi/Kconfig | 8 +
drivers/spi/Makefile | 1 +
drivers/spi/bcm63xx_hsspi.c | 413 ++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 422 insertions(+)
create mode 100644 drivers/spi/bcm63xx_hsspi.c
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 0b408db..e49ec36 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -40,6 +40,14 @@ config ATMEL_SPI
many AT32 (AVR32) and AT91 (ARM) chips. This driver can be
used to access the SPI Flash, such as AT25DF321.
+config BCM6328_HSSPI
+ bool "BCM6328 HSSPI driver"
+ depends on ARCH_BMIPS
+ help
+ Enable the BCM6328 HSSPI driver. This driver can be used to
+ access the SPI NOR flash on platforms embedding this Broadcom
+ SPI core.
+
choice
prompt "BCM63xx SPI driver"
depends on ARCH_BMIPS
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 2795a34..7ad0da1 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -19,6 +19,7 @@ obj-$(CONFIG_ALTERA_SPI) += altera_spi.o
obj-$(CONFIG_ATH79_SPI) += ath79_spi.o
obj-$(CONFIG_ATMEL_DATAFLASH_SPI) += atmel_dataflash_spi.o
obj-$(CONFIG_ATMEL_SPI) += atmel_spi.o
+obj-$(CONFIG_BCM6328_HSSPI) += bcm63xx_hsspi.o
obj-$(CONFIG_BCM6348_SPI)$(CONFIG_BCM6358_SPI) += bcm63xx_spi.o
obj-$(CONFIG_CADENCE_QSPI) += cadence_qspi.o cadence_qspi_apb.o
obj-$(CONFIG_CF_SPI) += cf_spi.o
diff --git a/drivers/spi/bcm63xx_hsspi.c b/drivers/spi/bcm63xx_hsspi.c
new file mode 100644
index 0000000..538c4ec
--- /dev/null
+++ b/drivers/spi/bcm63xx_hsspi.c
@@ -0,0 +1,413 @@
+/*
+ * Copyright (C) 2017 Álvaro Fernández Rojas <noltari@gmail.com>
+ *
+ * Derived from linux/drivers/spi/spi-bcm63xx-hsspi.c:
+ * Copyright (C) 2000-2010 Broadcom Corporation
+ * Copyright (C) 2012-2013 Jonas Gorski <jogo@openwrt.org>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <clk.h>
+#include <dm.h>
+#include <spi.h>
+#include <reset.h>
+#include <asm/io.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define SPI_PP_SEL 0
+
+#define SPI_MAX_SYNC_CLOCK 30000000
+
+/* SPI Control register */
+#define SPI_CTL_REG 0x000
+#define SPI_CTL_CS_POL_SHIFT 0
+#define SPI_CTL_CS_POL_MASK (0xff << SPI_CTL_CS_POL_SHIFT)
+#define SPI_CTL_CLK_GATE_SHIFT 16
+#define SPI_CTL_CLK_GATE_MASK (1 << SPI_CTL_CLK_GATE_SHIFT)
+#define SPI_CTL_CLK_POL_SHIFT 17
+#define SPI_CTL_CLK_POL_MASK (1 << SPI_CTL_CLK_POL_SHIFT)
+
+/* SPI Interrupts registers */
+#define SPI_IR_STAT_REG 0x008
+#define SPI_IR_ST_MASK_REG 0x00c
+#define SPI_IR_MASK_REG 0x010
+
+#define SPI_IR_CLEAR_ALL 0xff001f1f
+
+/* SPI Ping-Pong Command registers */
+#define SPI_PP_CMD_REG (0x080 + (0x40 * (SPI_PP_SEL)) + 0x00)
+#define SPI_PP_CMD_OP_SHIFT 0
+#define SPI_PP_CMD_OP_START (0x1 << SPI_PP_CMD_OP_SHIFT)
+#define SPI_PP_CMD_PFL_SHIFT 8
+#define SPI_PP_CMD_PFL_MASK (0x7 << SPI_PP_CMD_PFL_SHIFT)
+#define SPI_PP_CMD_SLAVE_SHIFT 12
+#define SPI_PP_CMD_SLAVE_MASK (0x7 << SPI_PP_CMD_SLAVE_SHIFT)
+
+/* SPI Ping-Pong Status registers */
+#define SPI_PP_STAT_REG (0x080 + (0x40 * (SPI_PP_SEL)) + 0x04)
+#define SPI_PP_STAT_SRCBUSY_SHIFT 1
+#define SPI_PP_STAT_SRCBUSY_MASK (1 << SPI_PP_STAT_SRCBUSY_SHIFT)
+
+/* SPI Profile Clock registers */
+#define SPI_PFL_CLK_REG(x) (0x100 + (0x20 * (x)) + 0x00)
+#define SPI_PFL_CLK_FREQ_SHIFT 0
+#define SPI_PFL_CLK_FREQ_MASK (0x3fff << SPI_PFL_CLK_FREQ_SHIFT)
+#define SPI_PFL_CLK_RSTLOOP_SHIFT 15
+#define SPI_PFL_CLK_RSTLOOP_MASK (1 << SPI_PFL_CLK_RSTLOOP_SHIFT)
+
+/* SPI Profile Signal registers */
+#define SPI_PFL_SIG_REG(x) (0x100 + (0x20 * (x)) + 0x04)
+#define SPI_PFL_SIG_LATCHRIS_SHIFT 12
+#define SPI_PFL_SIG_LATCHRIS_MASK (1 << SPI_PFL_SIG_LATCHRIS_SHIFT)
+#define SPI_PFL_SIG_LAUNCHRIS_SHIFT 13
+#define SPI_PFL_SIG_LAUNCHRIS_MASK (1 << SPI_PFL_SIG_LAUNCHRIS_SHIFT)
+#define SPI_PFL_SIG_ASYNCIN_SHIFT 16
+#define SPI_PFL_SIG_ASYNCIN_MASK (1 << SPI_PFL_SIG_ASYNCIN_SHIFT)
+
+/* SPI Profile Mode registers */
+#define SPI_PFL_MODE_REG(x) (0x100 + (0x20 * (x)) + 0x08)
+#define SPI_PFL_MODE_FILL_SHIFT 0
+#define SPI_PFL_MODE_FILL_MASK (0xff << SPI_PFL_MODE_FILL_SHIFT)
+#define SPI_PFL_MODE_MDRDSZ_SHIFT 16
+#define SPI_PFL_MODE_MDRDSZ_MASK (1 << SPI_PFL_MODE_MDRDSZ_SHIFT)
+#define SPI_PFL_MODE_MDWRSZ_SHIFT 18
+#define SPI_PFL_MODE_MDWRSZ_MASK (1 << SPI_PFL_MODE_MDWRSZ_SHIFT)
+#define SPI_PFL_MODE_3WIRE_SHIFT 20
+#define SPI_PFL_MODE_3WIRE_MASK (1 << SPI_PFL_MODE_3WIRE_SHIFT)
+
+/* SPI Ping-Pong FIFO registers */
+#define SPI_PP_FIFO_SIZE 0x200
+#define SPI_PP_FIFO_BASE (0x200 + \
+ (SPI_PP_FIFO_SIZE * SPI_PP_SEL))
+
+/* SPI Ping-Pong FIFO OP register */
+#define SPI_PP_FIFO_OP_SIZE 0x2
+#define SPI_PP_FIFO_OP_REG (SPI_PP_FIFO_BASE + 0x00)
+#define SPI_PP_FIFO_OP_BYTES_SHIFT 0
+#define SPI_PP_FIFO_OP_BYTES_MASK (0x3ff << SPI_PP_FIFO_OP_BYTES_SHIFT)
+#define SPI_PP_FIFO_OP_MBIT_SHIFT 11
+#define SPI_PP_FIFO_OP_MBIT_MASK (1 << SPI_PP_FIFO_OP_MBIT_SHIFT)
+#define SPI_PP_FIFO_OP_CODE_SHIFT 13
+#define SPI_PP_FIFO_OP_CODE_RW (1 << SPI_PP_FIFO_OP_CODE_SHIFT)
+#define SPI_PP_FIFO_OP_CODE_W (2 << SPI_PP_FIFO_OP_CODE_SHIFT)
+#define SPI_PP_FIFO_OP_CODE_R (3 << SPI_PP_FIFO_OP_CODE_SHIFT)
+
+struct bcm63xx_hsspi_priv {
+ void __iomem *regs;
+ ulong clk_rate;
+ uint8_t num_cs;
+ uint8_t cs_pols;
+ uint speed;
+};
+
+static int bcm63xx_hsspi_cs_info(struct udevice *bus, uint cs,
+ struct spi_cs_info *info)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(bus);
+
+ if (cs >= priv->num_cs) {
+ error("no cs %u\n", cs);
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int bcm63xx_hsspi_set_mode(struct udevice *bus, uint mode)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(bus);
+
+ /* clock polarity */
+ if (mode & SPI_CPOL)
+ setbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CLK_POL_MASK);
+ else
+ clrbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CLK_POL_MASK);
+
+ return 0;
+}
+
+static int bcm63xx_hsspi_set_speed(struct udevice *bus, uint speed)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(bus);
+
+ priv->speed = speed;
+
+ return 0;
+}
+
+static void bcm63xx_hsspi_claim_cs(struct bcm63xx_hsspi_priv *priv,
+ struct dm_spi_slave_platdata *plat)
+{
+ uint32_t clr, set;
+
+ /* profile clock */
+ set = DIV_ROUND_UP(priv->clk_rate, priv->speed);
+ set = DIV_ROUND_UP(2048, set);
+ set &= SPI_PFL_CLK_FREQ_MASK;
+ set |= SPI_PFL_CLK_RSTLOOP_MASK;
+ writel_be(set, priv->regs + SPI_PFL_CLK_REG(plat->cs));
+
+ /* profile signal */
+ set = 0;
+ clr = SPI_PFL_SIG_LAUNCHRIS_MASK |
+ SPI_PFL_SIG_LATCHRIS_MASK |
+ SPI_PFL_SIG_ASYNCIN_MASK;
+
+ /* latch/launch config */
+ if (plat->mode & SPI_CPHA)
+ set |= SPI_PFL_SIG_LAUNCHRIS_MASK;
+ else
+ set |= SPI_PFL_SIG_LATCHRIS_MASK;
+
+ /* async clk */
+ if (priv->speed > SPI_MAX_SYNC_CLOCK)
+ set |= SPI_PFL_SIG_ASYNCIN_MASK;
+
+ clrsetbits_be32(priv->regs + SPI_PFL_SIG_REG(plat->cs), clr, set);
+
+ /* global control */
+ set = 0;
+ clr = 0;
+
+ /* invert cs polarity */
+ if (priv->cs_pols & BIT(plat->cs))
+ clr |= BIT(plat->cs);
+ else
+ set |= BIT(plat->cs);
+
+ /* invert dummy cs polarity */
+ if (priv->cs_pols & BIT(!plat->cs))
+ clr |= BIT(!plat->cs);
+ else
+ set |= BIT(!plat->cs);
+
+ clrsetbits_be32(priv->regs + SPI_CTL_REG, clr, set);
+}
+
+static void bcm63xx_hsspi_release_cs(struct bcm63xx_hsspi_priv *priv)
+{
+ /* restore cs polarities */
+ clrsetbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CS_POL_MASK,
+ priv->cs_pols);
+}
+
+/*
+ * BCM63xx HSSPI driver doesn't allow keeping CS active between transfers
+ * because they are controlled by HW.
+ * However, it provides a mechanism to prepend write transfers prior to read
+ * transfers (with a maximum prepend of 15 bytes), which is usually enough for
+ * SPI-connected flashes since reading requires prepending a write transfer of
+ * 5 bytes. On the other hand it also provides a way to invert each CS
+ * polarity, not only between transfers like the older BCM63xx SPI driver, but
+ * also the rest of the time.
+ *
+ * Instead of using the prepend mechanism, this implementation inverts the
+ * polarity of both the desired CS and another dummy CS when the bus is
+ * claimed. This way, the dummy CS is restored to its inactive value when
+ * transfers are issued and the desired CS is preserved in its active value
+ * all the time. This hack is also used in the upstream linux driver and
+ * allows keeping CS active between trasnfers even if the HW doesn't give
+ * this possibility.
+ */
+static int bcm63xx_hsspi_xfer(struct udevice *dev, unsigned int bitlen,
+ const void *dout, void *din, unsigned long flags)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev->parent);
+ struct dm_spi_slave_platdata *plat = dev_get_parent_platdata(dev);
+ size_t data_bytes = bitlen / 8;
+ size_t step_size = SPI_PP_FIFO_SIZE;
+ uint16_t opcode = 0;
+ uint32_t val;
+ const uint8_t *tx = dout;
+ uint8_t *rx = din;
+
+ if (flags & SPI_XFER_BEGIN)
+ bcm63xx_hsspi_claim_cs(priv, plat);
+
+ /* fifo operation */
+ if (tx && rx)
+ opcode = SPI_PP_FIFO_OP_CODE_RW;
+ else if (rx)
+ opcode = SPI_PP_FIFO_OP_CODE_R;
+ else if (tx)
+ opcode = SPI_PP_FIFO_OP_CODE_W;
+
+ if (opcode != SPI_PP_FIFO_OP_CODE_R)
+ step_size -= SPI_PP_FIFO_OP_SIZE;
+
+ /* dual mode */
+ if ((opcode == SPI_PP_FIFO_OP_CODE_R && plat->mode == SPI_RX_DUAL) ||
+ (opcode == SPI_PP_FIFO_OP_CODE_W && plat->mode == SPI_TX_DUAL))
+ opcode |= SPI_PP_FIFO_OP_MBIT_MASK;
+
+ /* profile mode */
+ val = SPI_PFL_MODE_FILL_MASK |
+ SPI_PFL_MODE_MDRDSZ_MASK |
+ SPI_PFL_MODE_MDWRSZ_MASK;
+ if (plat->mode & SPI_3WIRE)
+ val |= SPI_PFL_MODE_3WIRE_MASK;
+ writel_be(val, priv->regs + SPI_PFL_MODE_REG(plat->cs));
+
+ /* transfer loop */
+ while (data_bytes > 0) {
+ size_t curr_step = min(step_size, data_bytes);
+
+ /* copy tx data */
+ if (tx) {
+ memcpy_toio(priv->regs + SPI_PP_FIFO_BASE +
+ SPI_PP_FIFO_OP_SIZE, tx, curr_step);
+ tx += curr_step;
+ }
+
+ /* set fifo operation */
+ writew_be(opcode | (curr_step & SPI_PP_FIFO_OP_BYTES_MASK),
+ priv->regs + SPI_PP_FIFO_OP_REG);
+
+ /* issue the transfer */
+ val = SPI_PP_CMD_OP_START;
+ val |= (plat->cs << SPI_PP_CMD_PFL_SHIFT) &
+ SPI_PP_CMD_PFL_MASK;
+ val |= (!plat->cs << SPI_PP_CMD_SLAVE_SHIFT) &
+ SPI_PP_CMD_SLAVE_MASK;
+ writel_be(val, priv->regs + SPI_PP_CMD_REG);
+
+ /* wait for completion */
+ do {
+ /* check ping-pong status */
+ val = readl_be(priv->regs + SPI_PP_STAT_REG);
+
+ /* transfer completed */
+ if (!(val & SPI_PP_STAT_SRCBUSY_MASK))
+ break;
+ } while (1);
+
+ /* copy rx data */
+ if (rx) {
+ memcpy_fromio(rx, priv->regs + SPI_PP_FIFO_BASE,
+ curr_step);
+ rx += curr_step;
+ }
+
+ data_bytes -= curr_step;
+ }
+
+ if (flags & SPI_XFER_END)
+ bcm63xx_hsspi_release_cs(priv);
+
+ return 0;
+}
+
+static const struct dm_spi_ops bcm63xx_hsspi_ops = {
+ .cs_info = bcm63xx_hsspi_cs_info,
+ .set_mode = bcm63xx_hsspi_set_mode,
+ .set_speed = bcm63xx_hsspi_set_speed,
+ .xfer = bcm63xx_hsspi_xfer,
+};
+
+static const struct udevice_id bcm63xx_hsspi_ids[] = {
+ { .compatible = "brcm,bcm6328-hsspi", },
+ { /* sentinel */ }
+};
+
+static int bcm63xx_hsspi_child_pre_probe(struct udevice *dev)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev->parent);
+ struct dm_spi_slave_platdata *plat = dev_get_parent_platdata(dev);
+
+ /* check cs */
+ if (plat->cs >= priv->num_cs) {
+ error("no cs %u\n", plat->cs);
+ return -ENODEV;
+ }
+
+ /* cs polarity */
+ if (plat->mode & SPI_CS_HIGH)
+ priv->cs_pols |= BIT(plat->cs);
+ else
+ priv->cs_pols &= ~BIT(plat->cs);
+
+ return 0;
+}
+
+static int bcm63xx_hsspi_probe(struct udevice *dev)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev);
+ struct reset_ctl rst_ctl;
+ struct clk clk;
+ fdt_addr_t addr;
+ fdt_size_t size;
+ int ret;
+
+ addr = devfdt_get_addr_size_index(dev, 0, &size);
+ if (addr == FDT_ADDR_T_NONE)
+ return -EINVAL;
+
+ priv->regs = ioremap(addr, size);
+ priv->num_cs = fdtdec_get_uint(gd->fdt_blob, dev_of_offset(dev),
+ "num-cs", 8);
+
+ /* enable clock */
+ ret = clk_get_by_name(dev, "hsspi", &clk);
+ if (ret < 0)
+ return ret;
+
+ ret = clk_enable(&clk);
+ if (ret < 0)
+ return ret;
+
+ ret = clk_free(&clk);
+ if (ret < 0)
+ return ret;
+
+ /* get clock rate */
+ ret = clk_get_by_name(dev, "pll", &clk);
+ if (ret < 0)
+ return ret;
+
+ priv->clk_rate = clk_get_rate(&clk);
+
+ ret = clk_free(&clk);
+ if (ret < 0)
+ return ret;
+
+ /* perform reset */
+ ret = reset_get_by_index(dev, 0, &rst_ctl);
+ if (ret < 0)
+ return ret;
+
+ ret = reset_deassert(&rst_ctl);
+ if (ret < 0)
+ return ret;
+
+ ret = reset_free(&rst_ctl);
+ if (ret < 0)
+ return ret;
+
+ /* initialize hardware */
+ writel_be(0, priv->regs + SPI_IR_MASK_REG);
+
+ /* clear pending interrupts */
+ writel_be(SPI_IR_CLEAR_ALL, priv->regs + SPI_IR_STAT_REG);
+
+ /* enable clk gate */
+ setbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CLK_GATE_MASK);
+
+ /* read default cs polarities */
+ priv->cs_pols = readl_be(priv->regs + SPI_CTL_REG) &
+ SPI_CTL_CS_POL_MASK;
+
+ return 0;
+}
+
+U_BOOT_DRIVER(bcm63xx_hsspi) = {
+ .name = "bcm63xx_hsspi",
+ .id = UCLASS_SPI,
+ .of_match = bcm63xx_hsspi_ids,
+ .ops = &bcm63xx_hsspi_ops,
+ .priv_auto_alloc_size = sizeof(struct bcm63xx_hsspi_priv),
+ .child_pre_probe = bcm63xx_hsspi_child_pre_probe,
+ .probe = bcm63xx_hsspi_probe,
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v2 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328
2017-06-03 10:15 ` [U-Boot] [PATCH v2 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
2017-06-03 10:16 ` [U-Boot] [PATCH v2 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
@ 2017-06-03 10:16 ` Álvaro Fernández Rojas
2017-06-04 9:04 ` Daniel Schwierzeck
2017-06-03 10:16 ` [U-Boot] [PATCH v2 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268 Álvaro Fernández Rojas
2017-06-03 10:16 ` [U-Boot] [PATCH v2 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un Álvaro Fernández Rojas
3 siblings, 1 reply; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-06-03 10:16 UTC (permalink / raw)
To: u-boot
This driver manages the SPI controller present on this SoC.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
---
v2: no changes
arch/mips/dts/brcm,bcm6328.dtsi | 24 ++++++++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/arch/mips/dts/brcm,bcm6328.dtsi b/arch/mips/dts/brcm,bcm6328.dtsi
index a996075..67d9278 100644
--- a/arch/mips/dts/brcm,bcm6328.dtsi
+++ b/arch/mips/dts/brcm,bcm6328.dtsi
@@ -13,6 +13,10 @@
/ {
compatible = "brcm,bcm6328";
+ aliases {
+ spi0 = &spi;
+ };
+
cpus {
reg = <0x10000000 0x4>;
#address-cells = <1>;
@@ -40,6 +44,12 @@
#size-cells = <1>;
u-boot,dm-pre-reloc;
+ hsspi_pll: hsspi-pll {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <133333333>;
+ };
+
periph_osc: periph-osc {
compatible = "fixed-clock";
#clock-cells = <0>;
@@ -123,6 +133,20 @@
status = "disabled";
};
+ spi: spi at 10001000 {
+ compatible = "brcm,bcm6328-hsspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x10001000 0x600>;
+ clocks = <&periph_clk BCM6328_CLK_HSSPI>, <&hsspi_pll>;
+ clock-names = "hsspi", "pll";
+ resets = <&periph_rst BCM6328_RST_SPI>;
+ spi-max-frequency = <33333334>;
+ num-cs = <3>;
+
+ status = "disabled";
+ };
+
periph_pwr: power-controller at 10001848 {
compatible = "brcm,bcm6328-power-domain";
reg = <0x10001848 0x4>;
--
2.1.4
^ permalink raw reply related [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v2 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268
2017-06-03 10:15 ` [U-Boot] [PATCH v2 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
2017-06-03 10:16 ` [U-Boot] [PATCH v2 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
2017-06-03 10:16 ` [U-Boot] [PATCH v2 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328 Álvaro Fernández Rojas
@ 2017-06-03 10:16 ` Álvaro Fernández Rojas
2017-06-04 9:04 ` Daniel Schwierzeck
2017-06-03 10:16 ` [U-Boot] [PATCH v2 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un Álvaro Fernández Rojas
3 siblings, 1 reply; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-06-03 10:16 UTC (permalink / raw)
To: u-boot
This driver manages the high speed SPI controller present on this SoC.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
---
v2: no changes
arch/mips/dts/brcm,bcm63268.dtsi | 21 +++++++++++++++++++++
1 file changed, 21 insertions(+)
diff --git a/arch/mips/dts/brcm,bcm63268.dtsi b/arch/mips/dts/brcm,bcm63268.dtsi
index 6e3d9c3..4d4e36c 100644
--- a/arch/mips/dts/brcm,bcm63268.dtsi
+++ b/arch/mips/dts/brcm,bcm63268.dtsi
@@ -15,6 +15,7 @@
aliases {
spi0 = &lsspi;
+ spi1 = &hsspi;
};
cpus {
@@ -44,6 +45,12 @@
#size-cells = <1>;
u-boot,dm-pre-reloc;
+ hsspi_pll: hsspi-pll {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <400000000>;
+ };
+
periph_osc: periph-osc {
compatible = "fixed-clock";
#clock-cells = <0>;
@@ -153,6 +160,20 @@
status = "disabled";
};
+ hsspi: spi at 10001000 {
+ compatible = "brcm,bcm6328-hsspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x10001000 0x600>;
+ clocks = <&periph_clk BCM63268_CLK_HSSPI>, <&hsspi_pll>;
+ clock-names = "hsspi", "pll";
+ resets = <&periph_rst BCM63268_RST_SPI>;
+ spi-max-frequency = <50000000>;
+ num-cs = <8>;
+
+ status = "disabled";
+ };
+
leds: led-controller at 10001900 {
compatible = "brcm,bcm6328-leds";
reg = <0x10001900 0x24>;
--
2.1.4
^ permalink raw reply related [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v2 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un
2017-06-03 10:15 ` [U-Boot] [PATCH v2 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
` (2 preceding siblings ...)
2017-06-03 10:16 ` [U-Boot] [PATCH v2 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268 Álvaro Fernández Rojas
@ 2017-06-03 10:16 ` Álvaro Fernández Rojas
2017-06-04 9:05 ` Daniel Schwierzeck
3 siblings, 1 reply; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-06-03 10:16 UTC (permalink / raw)
To: u-boot
It's a Macronix (mx25l12805d) 16 MB SPI flash.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
---
v2: no changes
arch/mips/dts/comtrend,ar-5387un.dts | 12 ++++++++++++
configs/comtrend_ar5387un_ram_defconfig | 8 ++++++++
2 files changed, 20 insertions(+)
diff --git a/arch/mips/dts/comtrend,ar-5387un.dts b/arch/mips/dts/comtrend,ar-5387un.dts
index 73f2b49..6067881 100644
--- a/arch/mips/dts/comtrend,ar-5387un.dts
+++ b/arch/mips/dts/comtrend,ar-5387un.dts
@@ -51,6 +51,18 @@
};
};
+&spi {
+ status = "okay";
+
+ spi-flash at 0 {
+ compatible = "spi-flash";
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <33333334>;
+ };
+};
+
&uart0 {
u-boot,dm-pre-reloc;
status = "okay";
diff --git a/configs/comtrend_ar5387un_ram_defconfig b/configs/comtrend_ar5387un_ram_defconfig
index 5b05fd2..38c6a28 100644
--- a/configs/comtrend_ar5387un_ram_defconfig
+++ b/configs/comtrend_ar5387un_ram_defconfig
@@ -1,5 +1,6 @@
CONFIG_ARCH_BMIPS=y
CONFIG_BAUDRATE=115200
+CONFIG_BCM6328_HSSPI=y
CONFIG_BCM6328_POWER_DOMAIN=y
CONFIG_BCM6345_CLK=y
CONFIG_BCM6345_SERIAL=y
@@ -27,6 +28,8 @@ CONFIG_CMD_MEMINFO=y
# CONFIG_CMD_NET is not set
# CONFIG_CMD_NFS is not set
# CONFIG_CMD_SAVEENV is not set
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
# CONFIG_CMD_XIMG is not set
CONFIG_DEFAULT_DEVICE_TREE="comtrend,ar-5387un"
CONFIG_DISPLAY_CPUINFO=y
@@ -34,6 +37,8 @@ CONFIG_DISPLAY_CPUINFO=y
CONFIG_DM_GPIO=y
CONFIG_DM_RESET=y
CONFIG_DM_SERIAL=y
+CONFIG_DM_SPI=y
+CONFIG_DM_SPI_FLASH=y
CONFIG_HUSH_PARSER=y
CONFIG_LED=y
CONFIG_LED_BCM6328=y
@@ -47,6 +52,9 @@ CONFIG_POWER_DOMAIN=y
CONFIG_RESET=y
CONFIG_RESET_BCM6345=y
CONFIG_SOC_BMIPS_BCM6328=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_MTD=y
+CONFIG_SPI_FLASH_MACRONIX=y
# CONFIG_SPL_SERIAL_PRESENT is not set
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SYS_NO_FLASH=y
--
2.1.4
^ permalink raw reply related [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v2 1/4] dm: spi: add BCM63xx HSSPI driver
2017-06-03 10:16 ` [U-Boot] [PATCH v2 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
@ 2017-06-04 9:02 ` Daniel Schwierzeck
2017-06-05 16:03 ` Álvaro Fernández Rojas
0 siblings, 1 reply; 45+ messages in thread
From: Daniel Schwierzeck @ 2017-06-04 9:02 UTC (permalink / raw)
To: u-boot
Am 03.06.2017 um 12:16 schrieb Álvaro Fernández Rojas:
> This driver is a simplified version of linux/drivers/spi/spi-bcm63xx-hsspi.c
>
> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
> ---
> v2: Introduce changes suggested by Simon Glass:
> - Split bcm63xx_hsspi_xfer() into smaller functions.
> - Check possible clock errors.
> - Check possible reset errors.
> - Switch to devfdt_get_addr_size_index().
> - Use setbits32_be() for clock gate.
>
> drivers/spi/Kconfig | 8 +
> drivers/spi/Makefile | 1 +
> drivers/spi/bcm63xx_hsspi.c | 413 ++++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 422 insertions(+)
> create mode 100644 drivers/spi/bcm63xx_hsspi.c
>
--
- Daniel
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170604/9169e867/attachment.sig>
^ permalink raw reply [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v2 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328
2017-06-03 10:16 ` [U-Boot] [PATCH v2 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328 Álvaro Fernández Rojas
@ 2017-06-04 9:04 ` Daniel Schwierzeck
2017-06-05 16:04 ` Álvaro Fernández Rojas
0 siblings, 1 reply; 45+ messages in thread
From: Daniel Schwierzeck @ 2017-06-04 9:04 UTC (permalink / raw)
To: u-boot
Am 03.06.2017 um 12:16 schrieb Álvaro Fernández Rojas:
> This driver manages the SPI controller present on this SoC.
>
> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
> ---
> v2: no changes
>
> arch/mips/dts/brcm,bcm6328.dtsi | 24 ++++++++++++++++++++++++
> 1 file changed, 24 insertions(+)
>
--
- Daniel
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170604/16475dc6/attachment.sig>
^ permalink raw reply [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v2 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268
2017-06-03 10:16 ` [U-Boot] [PATCH v2 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268 Álvaro Fernández Rojas
@ 2017-06-04 9:04 ` Daniel Schwierzeck
2017-06-05 16:04 ` Álvaro Fernández Rojas
0 siblings, 1 reply; 45+ messages in thread
From: Daniel Schwierzeck @ 2017-06-04 9:04 UTC (permalink / raw)
To: u-boot
Am 03.06.2017 um 12:16 schrieb Álvaro Fernández Rojas:
> This driver manages the high speed SPI controller present on this SoC.
>
> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
> ---
> v2: no changes
>
> arch/mips/dts/brcm,bcm63268.dtsi | 21 +++++++++++++++++++++
> 1 file changed, 21 insertions(+)
>
--
- Daniel
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170604/0c4a7b88/attachment.sig>
^ permalink raw reply [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v2 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un
2017-06-03 10:16 ` [U-Boot] [PATCH v2 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un Álvaro Fernández Rojas
@ 2017-06-04 9:05 ` Daniel Schwierzeck
2017-06-05 16:04 ` Álvaro Fernández Rojas
0 siblings, 1 reply; 45+ messages in thread
From: Daniel Schwierzeck @ 2017-06-04 9:05 UTC (permalink / raw)
To: u-boot
Am 03.06.2017 um 12:16 schrieb Álvaro Fernández Rojas:
> It's a Macronix (mx25l12805d) 16 MB SPI flash.
>
> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
> ---
> v2: no changes
>
> arch/mips/dts/comtrend,ar-5387un.dts | 12 ++++++++++++
> configs/comtrend_ar5387un_ram_defconfig | 8 ++++++++
> 2 files changed, 20 insertions(+)
>
--
- Daniel
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170604/7c395895/attachment.sig>
^ permalink raw reply [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v2 1/4] dm: spi: add BCM63xx HSSPI driver
2017-06-04 9:02 ` Daniel Schwierzeck
@ 2017-06-05 16:03 ` Álvaro Fernández Rojas
0 siblings, 0 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-06-05 16:03 UTC (permalink / raw)
To: u-boot
I just realized I didn't add Simon's reviews to v2...
Reviewed-by: Simon Glass <sjg@chromium.org>
El 04/06/2017 a las 11:02, Daniel Schwierzeck escribió:
>
>
> Am 03.06.2017 um 12:16 schrieb Álvaro Fernández Rojas:
>> This driver is a simplified version of linux/drivers/spi/spi-bcm63xx-hsspi.c
>>
>> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
>
> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
>
>> ---
>> v2: Introduce changes suggested by Simon Glass:
>> - Split bcm63xx_hsspi_xfer() into smaller functions.
>> - Check possible clock errors.
>> - Check possible reset errors.
>> - Switch to devfdt_get_addr_size_index().
>> - Use setbits32_be() for clock gate.
>>
>> drivers/spi/Kconfig | 8 +
>> drivers/spi/Makefile | 1 +
>> drivers/spi/bcm63xx_hsspi.c | 413 ++++++++++++++++++++++++++++++++++++++++++++
>> 3 files changed, 422 insertions(+)
>> create mode 100644 drivers/spi/bcm63xx_hsspi.c
>>
>
^ permalink raw reply [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v2 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328
2017-06-04 9:04 ` Daniel Schwierzeck
@ 2017-06-05 16:04 ` Álvaro Fernández Rojas
0 siblings, 0 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-06-05 16:04 UTC (permalink / raw)
To: u-boot
I just realized I didn't add Simon's reviews to v2...
Reviewed-by: Simon Glass <sjg@chromium.org>
El 04/06/2017 a las 11:04, Daniel Schwierzeck escribió:
>
>
> Am 03.06.2017 um 12:16 schrieb Álvaro Fernández Rojas:
>> This driver manages the SPI controller present on this SoC.
>>
>> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
>
> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
>
>> ---
>> v2: no changes
>>
>> arch/mips/dts/brcm,bcm6328.dtsi | 24 ++++++++++++++++++++++++
>> 1 file changed, 24 insertions(+)
>>
>
^ permalink raw reply [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v2 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268
2017-06-04 9:04 ` Daniel Schwierzeck
@ 2017-06-05 16:04 ` Álvaro Fernández Rojas
0 siblings, 0 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-06-05 16:04 UTC (permalink / raw)
To: u-boot
I just realized I didn't add Simon's reviews to v2...
Reviewed-by: Simon Glass <sjg@chromium.org>
El 04/06/2017 a las 11:04, Daniel Schwierzeck escribió:
>
>
> Am 03.06.2017 um 12:16 schrieb Álvaro Fernández Rojas:
>> This driver manages the high speed SPI controller present on this SoC.
>>
>> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
>
> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
>
>> ---
>> v2: no changes
>>
>> arch/mips/dts/brcm,bcm63268.dtsi | 21 +++++++++++++++++++++
>> 1 file changed, 21 insertions(+)
>>
>
^ permalink raw reply [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v2 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un
2017-06-04 9:05 ` Daniel Schwierzeck
@ 2017-06-05 16:04 ` Álvaro Fernández Rojas
0 siblings, 0 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-06-05 16:04 UTC (permalink / raw)
To: u-boot
I just realized I didn't add Simon's reviews to v2...
Reviewed-by: Simon Glass <sjg@chromium.org>
El 04/06/2017 a las 11:05, Daniel Schwierzeck escribió:
>
>
> Am 03.06.2017 um 12:16 schrieb Álvaro Fernández Rojas:
>> It's a Macronix (mx25l12805d) 16 MB SPI flash.
>>
>> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
>
> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
>
>> ---
>> v2: no changes
>>
>> arch/mips/dts/comtrend,ar-5387un.dts | 12 ++++++++++++
>> configs/comtrend_ar5387un_ram_defconfig | 8 ++++++++
>> 2 files changed, 20 insertions(+)
>>
>
^ permalink raw reply [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v3 0/4] mips: bmips: add HSSPI support
2017-05-23 19:18 [U-Boot] [PATCH 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
` (4 preceding siblings ...)
2017-06-03 10:15 ` [U-Boot] [PATCH v2 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
@ 2017-06-14 9:59 ` Álvaro Fernández Rojas
2017-06-14 9:59 ` [U-Boot] [PATCH v3 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
` (3 more replies)
2017-07-30 12:14 ` [U-Boot] [PATCH v4 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
` (2 subsequent siblings)
8 siblings, 4 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-06-14 9:59 UTC (permalink / raw)
To: u-boot
BCM63xx HSSPI controller has the same issue as BCM63xx SPI controller: it
doesn't allow keeping CS active between transfers.
However, this controller allows changing CS polarities, which is used in the
linux upstream driver to manage CS as desired.
v3: Switch to CONFIG_BCM63XX_HSSPI and rebase on top of SPI v4.
v2: Introduce changes suggested by Simon Glass:
- Split bcm63xx_hsspi_xfer() into smaller functions.
- Check possible clock errors.
- Check possible reset errors.
- Switch to devfdt_get_addr_size_index().
- Use setbits32_be() for clock gate.
Álvaro Fernández Rojas (4):
dm: spi: add BCM63xx HSSPI driver
mips: bmips: add bcm63xx-hsspi driver support for BCM6328
mips: bmips: add bcm63xx-hsspi driver support for BCM63268
mips: bmips: enable the SPI flash on the Comtrend AR-5387un
arch/mips/dts/brcm,bcm63268.dtsi | 21 ++
arch/mips/dts/brcm,bcm6328.dtsi | 24 ++
arch/mips/dts/comtrend,ar-5387un.dts | 12 +
configs/comtrend_ar5387un_ram_defconfig | 8 +
drivers/spi/Kconfig | 8 +
drivers/spi/Makefile | 1 +
drivers/spi/bcm63xx_hsspi.c | 413 ++++++++++++++++++++++++++++++++
7 files changed, 487 insertions(+)
create mode 100644 drivers/spi/bcm63xx_hsspi.c
--
2.1.4
^ permalink raw reply [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v3 1/4] dm: spi: add BCM63xx HSSPI driver
2017-06-14 9:59 ` [U-Boot] [PATCH v3 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
@ 2017-06-14 9:59 ` Álvaro Fernández Rojas
2017-06-14 9:59 ` [U-Boot] [PATCH v3 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328 Álvaro Fernández Rojas
` (2 subsequent siblings)
3 siblings, 0 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-06-14 9:59 UTC (permalink / raw)
To: u-boot
This driver is a simplified version of linux/drivers/spi/spi-bcm63xx-hsspi.c
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
---
v3: Switch to CONFIG_BCM63XX_HSSPI and rebase on top of SPI v4.
v2: Introduce changes suggested by Simon Glass:
- Split bcm63xx_hsspi_xfer() into smaller functions.
- Check possible clock errors.
- Check possible reset errors.
- Switch to devfdt_get_addr_size_index().
- Use setbits32_be() for clock gate.
drivers/spi/Kconfig | 8 +
drivers/spi/Makefile | 1 +
drivers/spi/bcm63xx_hsspi.c | 413 ++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 422 insertions(+)
create mode 100644 drivers/spi/bcm63xx_hsspi.c
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 6da78bd..4ef9db7 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -40,6 +40,14 @@ config ATMEL_SPI
many AT32 (AVR32) and AT91 (ARM) chips. This driver can be
used to access the SPI Flash, such as AT25DF321.
+config BCM63XX_HSSPI
+ bool "BCM63XX HSSPI driver"
+ depends on ARCH_BMIPS
+ help
+ Enable the BCM6328 HSSPI driver. This driver can be used to
+ access the SPI NOR flash on platforms embedding this Broadcom
+ SPI core.
+
config BCM63XX_SPI
bool "BCM6348 SPI driver"
depends on ARCH_BMIPS
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 260ba06..f25d2c5 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -19,6 +19,7 @@ obj-$(CONFIG_ALTERA_SPI) += altera_spi.o
obj-$(CONFIG_ATH79_SPI) += ath79_spi.o
obj-$(CONFIG_ATMEL_DATAFLASH_SPI) += atmel_dataflash_spi.o
obj-$(CONFIG_ATMEL_SPI) += atmel_spi.o
+obj-$(CONFIG_BCM63XX_HSSPI) += bcm63xx_hsspi.o
obj-$(CONFIG_BCM63XX_SPI) += bcm63xx_spi.o
obj-$(CONFIG_CADENCE_QSPI) += cadence_qspi.o cadence_qspi_apb.o
obj-$(CONFIG_CF_SPI) += cf_spi.o
diff --git a/drivers/spi/bcm63xx_hsspi.c b/drivers/spi/bcm63xx_hsspi.c
new file mode 100644
index 0000000..538c4ec
--- /dev/null
+++ b/drivers/spi/bcm63xx_hsspi.c
@@ -0,0 +1,413 @@
+/*
+ * Copyright (C) 2017 Álvaro Fernández Rojas <noltari@gmail.com>
+ *
+ * Derived from linux/drivers/spi/spi-bcm63xx-hsspi.c:
+ * Copyright (C) 2000-2010 Broadcom Corporation
+ * Copyright (C) 2012-2013 Jonas Gorski <jogo@openwrt.org>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <clk.h>
+#include <dm.h>
+#include <spi.h>
+#include <reset.h>
+#include <asm/io.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define SPI_PP_SEL 0
+
+#define SPI_MAX_SYNC_CLOCK 30000000
+
+/* SPI Control register */
+#define SPI_CTL_REG 0x000
+#define SPI_CTL_CS_POL_SHIFT 0
+#define SPI_CTL_CS_POL_MASK (0xff << SPI_CTL_CS_POL_SHIFT)
+#define SPI_CTL_CLK_GATE_SHIFT 16
+#define SPI_CTL_CLK_GATE_MASK (1 << SPI_CTL_CLK_GATE_SHIFT)
+#define SPI_CTL_CLK_POL_SHIFT 17
+#define SPI_CTL_CLK_POL_MASK (1 << SPI_CTL_CLK_POL_SHIFT)
+
+/* SPI Interrupts registers */
+#define SPI_IR_STAT_REG 0x008
+#define SPI_IR_ST_MASK_REG 0x00c
+#define SPI_IR_MASK_REG 0x010
+
+#define SPI_IR_CLEAR_ALL 0xff001f1f
+
+/* SPI Ping-Pong Command registers */
+#define SPI_PP_CMD_REG (0x080 + (0x40 * (SPI_PP_SEL)) + 0x00)
+#define SPI_PP_CMD_OP_SHIFT 0
+#define SPI_PP_CMD_OP_START (0x1 << SPI_PP_CMD_OP_SHIFT)
+#define SPI_PP_CMD_PFL_SHIFT 8
+#define SPI_PP_CMD_PFL_MASK (0x7 << SPI_PP_CMD_PFL_SHIFT)
+#define SPI_PP_CMD_SLAVE_SHIFT 12
+#define SPI_PP_CMD_SLAVE_MASK (0x7 << SPI_PP_CMD_SLAVE_SHIFT)
+
+/* SPI Ping-Pong Status registers */
+#define SPI_PP_STAT_REG (0x080 + (0x40 * (SPI_PP_SEL)) + 0x04)
+#define SPI_PP_STAT_SRCBUSY_SHIFT 1
+#define SPI_PP_STAT_SRCBUSY_MASK (1 << SPI_PP_STAT_SRCBUSY_SHIFT)
+
+/* SPI Profile Clock registers */
+#define SPI_PFL_CLK_REG(x) (0x100 + (0x20 * (x)) + 0x00)
+#define SPI_PFL_CLK_FREQ_SHIFT 0
+#define SPI_PFL_CLK_FREQ_MASK (0x3fff << SPI_PFL_CLK_FREQ_SHIFT)
+#define SPI_PFL_CLK_RSTLOOP_SHIFT 15
+#define SPI_PFL_CLK_RSTLOOP_MASK (1 << SPI_PFL_CLK_RSTLOOP_SHIFT)
+
+/* SPI Profile Signal registers */
+#define SPI_PFL_SIG_REG(x) (0x100 + (0x20 * (x)) + 0x04)
+#define SPI_PFL_SIG_LATCHRIS_SHIFT 12
+#define SPI_PFL_SIG_LATCHRIS_MASK (1 << SPI_PFL_SIG_LATCHRIS_SHIFT)
+#define SPI_PFL_SIG_LAUNCHRIS_SHIFT 13
+#define SPI_PFL_SIG_LAUNCHRIS_MASK (1 << SPI_PFL_SIG_LAUNCHRIS_SHIFT)
+#define SPI_PFL_SIG_ASYNCIN_SHIFT 16
+#define SPI_PFL_SIG_ASYNCIN_MASK (1 << SPI_PFL_SIG_ASYNCIN_SHIFT)
+
+/* SPI Profile Mode registers */
+#define SPI_PFL_MODE_REG(x) (0x100 + (0x20 * (x)) + 0x08)
+#define SPI_PFL_MODE_FILL_SHIFT 0
+#define SPI_PFL_MODE_FILL_MASK (0xff << SPI_PFL_MODE_FILL_SHIFT)
+#define SPI_PFL_MODE_MDRDSZ_SHIFT 16
+#define SPI_PFL_MODE_MDRDSZ_MASK (1 << SPI_PFL_MODE_MDRDSZ_SHIFT)
+#define SPI_PFL_MODE_MDWRSZ_SHIFT 18
+#define SPI_PFL_MODE_MDWRSZ_MASK (1 << SPI_PFL_MODE_MDWRSZ_SHIFT)
+#define SPI_PFL_MODE_3WIRE_SHIFT 20
+#define SPI_PFL_MODE_3WIRE_MASK (1 << SPI_PFL_MODE_3WIRE_SHIFT)
+
+/* SPI Ping-Pong FIFO registers */
+#define SPI_PP_FIFO_SIZE 0x200
+#define SPI_PP_FIFO_BASE (0x200 + \
+ (SPI_PP_FIFO_SIZE * SPI_PP_SEL))
+
+/* SPI Ping-Pong FIFO OP register */
+#define SPI_PP_FIFO_OP_SIZE 0x2
+#define SPI_PP_FIFO_OP_REG (SPI_PP_FIFO_BASE + 0x00)
+#define SPI_PP_FIFO_OP_BYTES_SHIFT 0
+#define SPI_PP_FIFO_OP_BYTES_MASK (0x3ff << SPI_PP_FIFO_OP_BYTES_SHIFT)
+#define SPI_PP_FIFO_OP_MBIT_SHIFT 11
+#define SPI_PP_FIFO_OP_MBIT_MASK (1 << SPI_PP_FIFO_OP_MBIT_SHIFT)
+#define SPI_PP_FIFO_OP_CODE_SHIFT 13
+#define SPI_PP_FIFO_OP_CODE_RW (1 << SPI_PP_FIFO_OP_CODE_SHIFT)
+#define SPI_PP_FIFO_OP_CODE_W (2 << SPI_PP_FIFO_OP_CODE_SHIFT)
+#define SPI_PP_FIFO_OP_CODE_R (3 << SPI_PP_FIFO_OP_CODE_SHIFT)
+
+struct bcm63xx_hsspi_priv {
+ void __iomem *regs;
+ ulong clk_rate;
+ uint8_t num_cs;
+ uint8_t cs_pols;
+ uint speed;
+};
+
+static int bcm63xx_hsspi_cs_info(struct udevice *bus, uint cs,
+ struct spi_cs_info *info)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(bus);
+
+ if (cs >= priv->num_cs) {
+ error("no cs %u\n", cs);
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int bcm63xx_hsspi_set_mode(struct udevice *bus, uint mode)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(bus);
+
+ /* clock polarity */
+ if (mode & SPI_CPOL)
+ setbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CLK_POL_MASK);
+ else
+ clrbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CLK_POL_MASK);
+
+ return 0;
+}
+
+static int bcm63xx_hsspi_set_speed(struct udevice *bus, uint speed)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(bus);
+
+ priv->speed = speed;
+
+ return 0;
+}
+
+static void bcm63xx_hsspi_claim_cs(struct bcm63xx_hsspi_priv *priv,
+ struct dm_spi_slave_platdata *plat)
+{
+ uint32_t clr, set;
+
+ /* profile clock */
+ set = DIV_ROUND_UP(priv->clk_rate, priv->speed);
+ set = DIV_ROUND_UP(2048, set);
+ set &= SPI_PFL_CLK_FREQ_MASK;
+ set |= SPI_PFL_CLK_RSTLOOP_MASK;
+ writel_be(set, priv->regs + SPI_PFL_CLK_REG(plat->cs));
+
+ /* profile signal */
+ set = 0;
+ clr = SPI_PFL_SIG_LAUNCHRIS_MASK |
+ SPI_PFL_SIG_LATCHRIS_MASK |
+ SPI_PFL_SIG_ASYNCIN_MASK;
+
+ /* latch/launch config */
+ if (plat->mode & SPI_CPHA)
+ set |= SPI_PFL_SIG_LAUNCHRIS_MASK;
+ else
+ set |= SPI_PFL_SIG_LATCHRIS_MASK;
+
+ /* async clk */
+ if (priv->speed > SPI_MAX_SYNC_CLOCK)
+ set |= SPI_PFL_SIG_ASYNCIN_MASK;
+
+ clrsetbits_be32(priv->regs + SPI_PFL_SIG_REG(plat->cs), clr, set);
+
+ /* global control */
+ set = 0;
+ clr = 0;
+
+ /* invert cs polarity */
+ if (priv->cs_pols & BIT(plat->cs))
+ clr |= BIT(plat->cs);
+ else
+ set |= BIT(plat->cs);
+
+ /* invert dummy cs polarity */
+ if (priv->cs_pols & BIT(!plat->cs))
+ clr |= BIT(!plat->cs);
+ else
+ set |= BIT(!plat->cs);
+
+ clrsetbits_be32(priv->regs + SPI_CTL_REG, clr, set);
+}
+
+static void bcm63xx_hsspi_release_cs(struct bcm63xx_hsspi_priv *priv)
+{
+ /* restore cs polarities */
+ clrsetbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CS_POL_MASK,
+ priv->cs_pols);
+}
+
+/*
+ * BCM63xx HSSPI driver doesn't allow keeping CS active between transfers
+ * because they are controlled by HW.
+ * However, it provides a mechanism to prepend write transfers prior to read
+ * transfers (with a maximum prepend of 15 bytes), which is usually enough for
+ * SPI-connected flashes since reading requires prepending a write transfer of
+ * 5 bytes. On the other hand it also provides a way to invert each CS
+ * polarity, not only between transfers like the older BCM63xx SPI driver, but
+ * also the rest of the time.
+ *
+ * Instead of using the prepend mechanism, this implementation inverts the
+ * polarity of both the desired CS and another dummy CS when the bus is
+ * claimed. This way, the dummy CS is restored to its inactive value when
+ * transfers are issued and the desired CS is preserved in its active value
+ * all the time. This hack is also used in the upstream linux driver and
+ * allows keeping CS active between trasnfers even if the HW doesn't give
+ * this possibility.
+ */
+static int bcm63xx_hsspi_xfer(struct udevice *dev, unsigned int bitlen,
+ const void *dout, void *din, unsigned long flags)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev->parent);
+ struct dm_spi_slave_platdata *plat = dev_get_parent_platdata(dev);
+ size_t data_bytes = bitlen / 8;
+ size_t step_size = SPI_PP_FIFO_SIZE;
+ uint16_t opcode = 0;
+ uint32_t val;
+ const uint8_t *tx = dout;
+ uint8_t *rx = din;
+
+ if (flags & SPI_XFER_BEGIN)
+ bcm63xx_hsspi_claim_cs(priv, plat);
+
+ /* fifo operation */
+ if (tx && rx)
+ opcode = SPI_PP_FIFO_OP_CODE_RW;
+ else if (rx)
+ opcode = SPI_PP_FIFO_OP_CODE_R;
+ else if (tx)
+ opcode = SPI_PP_FIFO_OP_CODE_W;
+
+ if (opcode != SPI_PP_FIFO_OP_CODE_R)
+ step_size -= SPI_PP_FIFO_OP_SIZE;
+
+ /* dual mode */
+ if ((opcode == SPI_PP_FIFO_OP_CODE_R && plat->mode == SPI_RX_DUAL) ||
+ (opcode == SPI_PP_FIFO_OP_CODE_W && plat->mode == SPI_TX_DUAL))
+ opcode |= SPI_PP_FIFO_OP_MBIT_MASK;
+
+ /* profile mode */
+ val = SPI_PFL_MODE_FILL_MASK |
+ SPI_PFL_MODE_MDRDSZ_MASK |
+ SPI_PFL_MODE_MDWRSZ_MASK;
+ if (plat->mode & SPI_3WIRE)
+ val |= SPI_PFL_MODE_3WIRE_MASK;
+ writel_be(val, priv->regs + SPI_PFL_MODE_REG(plat->cs));
+
+ /* transfer loop */
+ while (data_bytes > 0) {
+ size_t curr_step = min(step_size, data_bytes);
+
+ /* copy tx data */
+ if (tx) {
+ memcpy_toio(priv->regs + SPI_PP_FIFO_BASE +
+ SPI_PP_FIFO_OP_SIZE, tx, curr_step);
+ tx += curr_step;
+ }
+
+ /* set fifo operation */
+ writew_be(opcode | (curr_step & SPI_PP_FIFO_OP_BYTES_MASK),
+ priv->regs + SPI_PP_FIFO_OP_REG);
+
+ /* issue the transfer */
+ val = SPI_PP_CMD_OP_START;
+ val |= (plat->cs << SPI_PP_CMD_PFL_SHIFT) &
+ SPI_PP_CMD_PFL_MASK;
+ val |= (!plat->cs << SPI_PP_CMD_SLAVE_SHIFT) &
+ SPI_PP_CMD_SLAVE_MASK;
+ writel_be(val, priv->regs + SPI_PP_CMD_REG);
+
+ /* wait for completion */
+ do {
+ /* check ping-pong status */
+ val = readl_be(priv->regs + SPI_PP_STAT_REG);
+
+ /* transfer completed */
+ if (!(val & SPI_PP_STAT_SRCBUSY_MASK))
+ break;
+ } while (1);
+
+ /* copy rx data */
+ if (rx) {
+ memcpy_fromio(rx, priv->regs + SPI_PP_FIFO_BASE,
+ curr_step);
+ rx += curr_step;
+ }
+
+ data_bytes -= curr_step;
+ }
+
+ if (flags & SPI_XFER_END)
+ bcm63xx_hsspi_release_cs(priv);
+
+ return 0;
+}
+
+static const struct dm_spi_ops bcm63xx_hsspi_ops = {
+ .cs_info = bcm63xx_hsspi_cs_info,
+ .set_mode = bcm63xx_hsspi_set_mode,
+ .set_speed = bcm63xx_hsspi_set_speed,
+ .xfer = bcm63xx_hsspi_xfer,
+};
+
+static const struct udevice_id bcm63xx_hsspi_ids[] = {
+ { .compatible = "brcm,bcm6328-hsspi", },
+ { /* sentinel */ }
+};
+
+static int bcm63xx_hsspi_child_pre_probe(struct udevice *dev)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev->parent);
+ struct dm_spi_slave_platdata *plat = dev_get_parent_platdata(dev);
+
+ /* check cs */
+ if (plat->cs >= priv->num_cs) {
+ error("no cs %u\n", plat->cs);
+ return -ENODEV;
+ }
+
+ /* cs polarity */
+ if (plat->mode & SPI_CS_HIGH)
+ priv->cs_pols |= BIT(plat->cs);
+ else
+ priv->cs_pols &= ~BIT(plat->cs);
+
+ return 0;
+}
+
+static int bcm63xx_hsspi_probe(struct udevice *dev)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev);
+ struct reset_ctl rst_ctl;
+ struct clk clk;
+ fdt_addr_t addr;
+ fdt_size_t size;
+ int ret;
+
+ addr = devfdt_get_addr_size_index(dev, 0, &size);
+ if (addr == FDT_ADDR_T_NONE)
+ return -EINVAL;
+
+ priv->regs = ioremap(addr, size);
+ priv->num_cs = fdtdec_get_uint(gd->fdt_blob, dev_of_offset(dev),
+ "num-cs", 8);
+
+ /* enable clock */
+ ret = clk_get_by_name(dev, "hsspi", &clk);
+ if (ret < 0)
+ return ret;
+
+ ret = clk_enable(&clk);
+ if (ret < 0)
+ return ret;
+
+ ret = clk_free(&clk);
+ if (ret < 0)
+ return ret;
+
+ /* get clock rate */
+ ret = clk_get_by_name(dev, "pll", &clk);
+ if (ret < 0)
+ return ret;
+
+ priv->clk_rate = clk_get_rate(&clk);
+
+ ret = clk_free(&clk);
+ if (ret < 0)
+ return ret;
+
+ /* perform reset */
+ ret = reset_get_by_index(dev, 0, &rst_ctl);
+ if (ret < 0)
+ return ret;
+
+ ret = reset_deassert(&rst_ctl);
+ if (ret < 0)
+ return ret;
+
+ ret = reset_free(&rst_ctl);
+ if (ret < 0)
+ return ret;
+
+ /* initialize hardware */
+ writel_be(0, priv->regs + SPI_IR_MASK_REG);
+
+ /* clear pending interrupts */
+ writel_be(SPI_IR_CLEAR_ALL, priv->regs + SPI_IR_STAT_REG);
+
+ /* enable clk gate */
+ setbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CLK_GATE_MASK);
+
+ /* read default cs polarities */
+ priv->cs_pols = readl_be(priv->regs + SPI_CTL_REG) &
+ SPI_CTL_CS_POL_MASK;
+
+ return 0;
+}
+
+U_BOOT_DRIVER(bcm63xx_hsspi) = {
+ .name = "bcm63xx_hsspi",
+ .id = UCLASS_SPI,
+ .of_match = bcm63xx_hsspi_ids,
+ .ops = &bcm63xx_hsspi_ops,
+ .priv_auto_alloc_size = sizeof(struct bcm63xx_hsspi_priv),
+ .child_pre_probe = bcm63xx_hsspi_child_pre_probe,
+ .probe = bcm63xx_hsspi_probe,
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v3 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328
2017-06-14 9:59 ` [U-Boot] [PATCH v3 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
2017-06-14 9:59 ` [U-Boot] [PATCH v3 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
@ 2017-06-14 9:59 ` Álvaro Fernández Rojas
2017-06-14 9:59 ` [U-Boot] [PATCH v3 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268 Álvaro Fernández Rojas
2017-06-14 9:59 ` [U-Boot] [PATCH v3 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un Álvaro Fernández Rojas
3 siblings, 0 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-06-14 9:59 UTC (permalink / raw)
To: u-boot
This driver manages the SPI controller present on this SoC.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
---
v3: no changes
v2: no changes
arch/mips/dts/brcm,bcm6328.dtsi | 24 ++++++++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/arch/mips/dts/brcm,bcm6328.dtsi b/arch/mips/dts/brcm,bcm6328.dtsi
index a996075..67d9278 100644
--- a/arch/mips/dts/brcm,bcm6328.dtsi
+++ b/arch/mips/dts/brcm,bcm6328.dtsi
@@ -13,6 +13,10 @@
/ {
compatible = "brcm,bcm6328";
+ aliases {
+ spi0 = &spi;
+ };
+
cpus {
reg = <0x10000000 0x4>;
#address-cells = <1>;
@@ -40,6 +44,12 @@
#size-cells = <1>;
u-boot,dm-pre-reloc;
+ hsspi_pll: hsspi-pll {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <133333333>;
+ };
+
periph_osc: periph-osc {
compatible = "fixed-clock";
#clock-cells = <0>;
@@ -123,6 +133,20 @@
status = "disabled";
};
+ spi: spi at 10001000 {
+ compatible = "brcm,bcm6328-hsspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x10001000 0x600>;
+ clocks = <&periph_clk BCM6328_CLK_HSSPI>, <&hsspi_pll>;
+ clock-names = "hsspi", "pll";
+ resets = <&periph_rst BCM6328_RST_SPI>;
+ spi-max-frequency = <33333334>;
+ num-cs = <3>;
+
+ status = "disabled";
+ };
+
periph_pwr: power-controller at 10001848 {
compatible = "brcm,bcm6328-power-domain";
reg = <0x10001848 0x4>;
--
2.1.4
^ permalink raw reply related [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v3 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268
2017-06-14 9:59 ` [U-Boot] [PATCH v3 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
2017-06-14 9:59 ` [U-Boot] [PATCH v3 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
2017-06-14 9:59 ` [U-Boot] [PATCH v3 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328 Álvaro Fernández Rojas
@ 2017-06-14 9:59 ` Álvaro Fernández Rojas
2017-06-14 9:59 ` [U-Boot] [PATCH v3 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un Álvaro Fernández Rojas
3 siblings, 0 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-06-14 9:59 UTC (permalink / raw)
To: u-boot
This driver manages the high speed SPI controller present on this SoC.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
---
v3: no changes
v2: no changes
arch/mips/dts/brcm,bcm63268.dtsi | 21 +++++++++++++++++++++
1 file changed, 21 insertions(+)
diff --git a/arch/mips/dts/brcm,bcm63268.dtsi b/arch/mips/dts/brcm,bcm63268.dtsi
index 6e3d9c3..4d4e36c 100644
--- a/arch/mips/dts/brcm,bcm63268.dtsi
+++ b/arch/mips/dts/brcm,bcm63268.dtsi
@@ -15,6 +15,7 @@
aliases {
spi0 = &lsspi;
+ spi1 = &hsspi;
};
cpus {
@@ -44,6 +45,12 @@
#size-cells = <1>;
u-boot,dm-pre-reloc;
+ hsspi_pll: hsspi-pll {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <400000000>;
+ };
+
periph_osc: periph-osc {
compatible = "fixed-clock";
#clock-cells = <0>;
@@ -153,6 +160,20 @@
status = "disabled";
};
+ hsspi: spi at 10001000 {
+ compatible = "brcm,bcm6328-hsspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x10001000 0x600>;
+ clocks = <&periph_clk BCM63268_CLK_HSSPI>, <&hsspi_pll>;
+ clock-names = "hsspi", "pll";
+ resets = <&periph_rst BCM63268_RST_SPI>;
+ spi-max-frequency = <50000000>;
+ num-cs = <8>;
+
+ status = "disabled";
+ };
+
leds: led-controller at 10001900 {
compatible = "brcm,bcm6328-leds";
reg = <0x10001900 0x24>;
--
2.1.4
^ permalink raw reply related [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v3 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un
2017-06-14 9:59 ` [U-Boot] [PATCH v3 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
` (2 preceding siblings ...)
2017-06-14 9:59 ` [U-Boot] [PATCH v3 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268 Álvaro Fernández Rojas
@ 2017-06-14 9:59 ` Álvaro Fernández Rojas
3 siblings, 0 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-06-14 9:59 UTC (permalink / raw)
To: u-boot
It's a Macronix (mx25l12805d) 16 MB SPI flash.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
---
v3: switch to CONFIG_BCM63XX_HSSPI
v2: no changes
arch/mips/dts/comtrend,ar-5387un.dts | 12 ++++++++++++
configs/comtrend_ar5387un_ram_defconfig | 8 ++++++++
2 files changed, 20 insertions(+)
diff --git a/arch/mips/dts/comtrend,ar-5387un.dts b/arch/mips/dts/comtrend,ar-5387un.dts
index 73f2b49..6067881 100644
--- a/arch/mips/dts/comtrend,ar-5387un.dts
+++ b/arch/mips/dts/comtrend,ar-5387un.dts
@@ -51,6 +51,18 @@
};
};
+&spi {
+ status = "okay";
+
+ spi-flash at 0 {
+ compatible = "spi-flash";
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <33333334>;
+ };
+};
+
&uart0 {
u-boot,dm-pre-reloc;
status = "okay";
diff --git a/configs/comtrend_ar5387un_ram_defconfig b/configs/comtrend_ar5387un_ram_defconfig
index 5b05fd2..b5433bd 100644
--- a/configs/comtrend_ar5387un_ram_defconfig
+++ b/configs/comtrend_ar5387un_ram_defconfig
@@ -3,6 +3,7 @@ CONFIG_BAUDRATE=115200
CONFIG_BCM6328_POWER_DOMAIN=y
CONFIG_BCM6345_CLK=y
CONFIG_BCM6345_SERIAL=y
+CONFIG_BCM63XX_HSSPI=y
CONFIG_BMIPS_BOOT_RAM=y
CONFIG_BOARD_COMTREND_AR5387UN=y
# CONFIG_CMD_BOOTD is not set
@@ -27,6 +28,8 @@ CONFIG_CMD_MEMINFO=y
# CONFIG_CMD_NET is not set
# CONFIG_CMD_NFS is not set
# CONFIG_CMD_SAVEENV is not set
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
# CONFIG_CMD_XIMG is not set
CONFIG_DEFAULT_DEVICE_TREE="comtrend,ar-5387un"
CONFIG_DISPLAY_CPUINFO=y
@@ -34,6 +37,8 @@ CONFIG_DISPLAY_CPUINFO=y
CONFIG_DM_GPIO=y
CONFIG_DM_RESET=y
CONFIG_DM_SERIAL=y
+CONFIG_DM_SPI=y
+CONFIG_DM_SPI_FLASH=y
CONFIG_HUSH_PARSER=y
CONFIG_LED=y
CONFIG_LED_BCM6328=y
@@ -47,6 +52,9 @@ CONFIG_POWER_DOMAIN=y
CONFIG_RESET=y
CONFIG_RESET_BCM6345=y
CONFIG_SOC_BMIPS_BCM6328=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_MTD=y
+CONFIG_SPI_FLASH_MACRONIX=y
# CONFIG_SPL_SERIAL_PRESENT is not set
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SYS_NO_FLASH=y
--
2.1.4
^ permalink raw reply related [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v4 0/4] mips: bmips: add HSSPI support
2017-05-23 19:18 [U-Boot] [PATCH 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
` (5 preceding siblings ...)
2017-06-14 9:59 ` [U-Boot] [PATCH v3 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
@ 2017-07-30 12:14 ` Álvaro Fernández Rojas
2017-07-30 12:14 ` [U-Boot] [PATCH v4 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
` (3 more replies)
2018-01-15 18:45 ` [U-Boot] [PATCH v5 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
2018-01-20 1:13 ` [U-Boot] [PATCH v6 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
8 siblings, 4 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-07-30 12:14 UTC (permalink / raw)
To: u-boot
BCM63xx HSSPI controller has the same issue as BCM63xx SPI controller: it
doesn't allow keeping CS active between transfers.
However, this controller allows changing CS polarities, which is used in the
linux upstream driver to manage CS as desired.
v4: Sync with master.
v3: Switch to CONFIG_BCM63XX_HSSPI and rebase on top of SPI v4.
v2: Introduce changes suggested by Simon Glass:
- Split bcm63xx_hsspi_xfer() into smaller functions.
- Check possible clock errors.
- Check possible reset errors.
- Switch to devfdt_get_addr_size_index().
- Use setbits32_be() for clock gate.
Álvaro Fernández Rojas (4):
dm: spi: add BCM63xx HSSPI driver
mips: bmips: add bcm63xx-hsspi driver support for BCM6328
mips: bmips: add bcm63xx-hsspi driver support for BCM63268
mips: bmips: enable the SPI flash on the Comtrend AR-5387un
arch/mips/dts/brcm,bcm63268.dtsi | 21 ++
arch/mips/dts/brcm,bcm6328.dtsi | 24 ++
arch/mips/dts/comtrend,ar-5387un.dts | 12 +
configs/comtrend_ar5387un_ram_defconfig | 8 +
drivers/spi/Kconfig | 8 +
drivers/spi/Makefile | 1 +
drivers/spi/bcm63xx_hsspi.c | 413 ++++++++++++++++++++++++++++++++
7 files changed, 487 insertions(+)
create mode 100644 drivers/spi/bcm63xx_hsspi.c
--
2.11.0
^ permalink raw reply [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v4 1/4] dm: spi: add BCM63xx HSSPI driver
2017-07-30 12:14 ` [U-Boot] [PATCH v4 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
@ 2017-07-30 12:14 ` Álvaro Fernández Rojas
2017-08-11 9:42 ` Jagan Teki
2017-07-30 12:14 ` [U-Boot] [PATCH v4 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328 Álvaro Fernández Rojas
` (2 subsequent siblings)
3 siblings, 1 reply; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-07-30 12:14 UTC (permalink / raw)
To: u-boot
This driver is a simplified version of linux/drivers/spi/spi-bcm63xx-hsspi.c
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
---
v4: no changes.
v3: Switch to CONFIG_BCM63XX_HSSPI and rebase on top of SPI v4.
v2: Introduce changes suggested by Simon Glass:
- Split bcm63xx_hsspi_xfer() into smaller functions.
- Check possible clock errors.
- Check possible reset errors.
- Switch to devfdt_get_addr_size_index().
- Use setbits32_be() for clock gate.
drivers/spi/Kconfig | 8 +
drivers/spi/Makefile | 1 +
drivers/spi/bcm63xx_hsspi.c | 413 ++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 422 insertions(+)
create mode 100644 drivers/spi/bcm63xx_hsspi.c
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 511643607b..97c3cb6103 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -40,6 +40,14 @@ config ATMEL_SPI
many AT91 (ARM) chips. This driver can be used to access
the SPI Flash, such as AT25DF321.
+config BCM63XX_HSSPI
+ bool "BCM63XX HSSPI driver"
+ depends on ARCH_BMIPS
+ help
+ Enable the BCM6328 HSSPI driver. This driver can be used to
+ access the SPI NOR flash on platforms embedding this Broadcom
+ SPI core.
+
config BCM63XX_SPI
bool "BCM6348 SPI driver"
depends on ARCH_BMIPS
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index d9802dd8c3..fefafbe333 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -19,6 +19,7 @@ obj-$(CONFIG_ALTERA_SPI) += altera_spi.o
obj-$(CONFIG_ATH79_SPI) += ath79_spi.o
obj-$(CONFIG_ATMEL_DATAFLASH_SPI) += atmel_dataflash_spi.o
obj-$(CONFIG_ATMEL_SPI) += atmel_spi.o
+obj-$(CONFIG_BCM63XX_HSSPI) += bcm63xx_hsspi.o
obj-$(CONFIG_BCM63XX_SPI) += bcm63xx_spi.o
obj-$(CONFIG_CADENCE_QSPI) += cadence_qspi.o cadence_qspi_apb.o
obj-$(CONFIG_CF_SPI) += cf_spi.o
diff --git a/drivers/spi/bcm63xx_hsspi.c b/drivers/spi/bcm63xx_hsspi.c
new file mode 100644
index 0000000000..538c4ec4fe
--- /dev/null
+++ b/drivers/spi/bcm63xx_hsspi.c
@@ -0,0 +1,413 @@
+/*
+ * Copyright (C) 2017 Álvaro Fernández Rojas <noltari@gmail.com>
+ *
+ * Derived from linux/drivers/spi/spi-bcm63xx-hsspi.c:
+ * Copyright (C) 2000-2010 Broadcom Corporation
+ * Copyright (C) 2012-2013 Jonas Gorski <jogo@openwrt.org>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <clk.h>
+#include <dm.h>
+#include <spi.h>
+#include <reset.h>
+#include <asm/io.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define SPI_PP_SEL 0
+
+#define SPI_MAX_SYNC_CLOCK 30000000
+
+/* SPI Control register */
+#define SPI_CTL_REG 0x000
+#define SPI_CTL_CS_POL_SHIFT 0
+#define SPI_CTL_CS_POL_MASK (0xff << SPI_CTL_CS_POL_SHIFT)
+#define SPI_CTL_CLK_GATE_SHIFT 16
+#define SPI_CTL_CLK_GATE_MASK (1 << SPI_CTL_CLK_GATE_SHIFT)
+#define SPI_CTL_CLK_POL_SHIFT 17
+#define SPI_CTL_CLK_POL_MASK (1 << SPI_CTL_CLK_POL_SHIFT)
+
+/* SPI Interrupts registers */
+#define SPI_IR_STAT_REG 0x008
+#define SPI_IR_ST_MASK_REG 0x00c
+#define SPI_IR_MASK_REG 0x010
+
+#define SPI_IR_CLEAR_ALL 0xff001f1f
+
+/* SPI Ping-Pong Command registers */
+#define SPI_PP_CMD_REG (0x080 + (0x40 * (SPI_PP_SEL)) + 0x00)
+#define SPI_PP_CMD_OP_SHIFT 0
+#define SPI_PP_CMD_OP_START (0x1 << SPI_PP_CMD_OP_SHIFT)
+#define SPI_PP_CMD_PFL_SHIFT 8
+#define SPI_PP_CMD_PFL_MASK (0x7 << SPI_PP_CMD_PFL_SHIFT)
+#define SPI_PP_CMD_SLAVE_SHIFT 12
+#define SPI_PP_CMD_SLAVE_MASK (0x7 << SPI_PP_CMD_SLAVE_SHIFT)
+
+/* SPI Ping-Pong Status registers */
+#define SPI_PP_STAT_REG (0x080 + (0x40 * (SPI_PP_SEL)) + 0x04)
+#define SPI_PP_STAT_SRCBUSY_SHIFT 1
+#define SPI_PP_STAT_SRCBUSY_MASK (1 << SPI_PP_STAT_SRCBUSY_SHIFT)
+
+/* SPI Profile Clock registers */
+#define SPI_PFL_CLK_REG(x) (0x100 + (0x20 * (x)) + 0x00)
+#define SPI_PFL_CLK_FREQ_SHIFT 0
+#define SPI_PFL_CLK_FREQ_MASK (0x3fff << SPI_PFL_CLK_FREQ_SHIFT)
+#define SPI_PFL_CLK_RSTLOOP_SHIFT 15
+#define SPI_PFL_CLK_RSTLOOP_MASK (1 << SPI_PFL_CLK_RSTLOOP_SHIFT)
+
+/* SPI Profile Signal registers */
+#define SPI_PFL_SIG_REG(x) (0x100 + (0x20 * (x)) + 0x04)
+#define SPI_PFL_SIG_LATCHRIS_SHIFT 12
+#define SPI_PFL_SIG_LATCHRIS_MASK (1 << SPI_PFL_SIG_LATCHRIS_SHIFT)
+#define SPI_PFL_SIG_LAUNCHRIS_SHIFT 13
+#define SPI_PFL_SIG_LAUNCHRIS_MASK (1 << SPI_PFL_SIG_LAUNCHRIS_SHIFT)
+#define SPI_PFL_SIG_ASYNCIN_SHIFT 16
+#define SPI_PFL_SIG_ASYNCIN_MASK (1 << SPI_PFL_SIG_ASYNCIN_SHIFT)
+
+/* SPI Profile Mode registers */
+#define SPI_PFL_MODE_REG(x) (0x100 + (0x20 * (x)) + 0x08)
+#define SPI_PFL_MODE_FILL_SHIFT 0
+#define SPI_PFL_MODE_FILL_MASK (0xff << SPI_PFL_MODE_FILL_SHIFT)
+#define SPI_PFL_MODE_MDRDSZ_SHIFT 16
+#define SPI_PFL_MODE_MDRDSZ_MASK (1 << SPI_PFL_MODE_MDRDSZ_SHIFT)
+#define SPI_PFL_MODE_MDWRSZ_SHIFT 18
+#define SPI_PFL_MODE_MDWRSZ_MASK (1 << SPI_PFL_MODE_MDWRSZ_SHIFT)
+#define SPI_PFL_MODE_3WIRE_SHIFT 20
+#define SPI_PFL_MODE_3WIRE_MASK (1 << SPI_PFL_MODE_3WIRE_SHIFT)
+
+/* SPI Ping-Pong FIFO registers */
+#define SPI_PP_FIFO_SIZE 0x200
+#define SPI_PP_FIFO_BASE (0x200 + \
+ (SPI_PP_FIFO_SIZE * SPI_PP_SEL))
+
+/* SPI Ping-Pong FIFO OP register */
+#define SPI_PP_FIFO_OP_SIZE 0x2
+#define SPI_PP_FIFO_OP_REG (SPI_PP_FIFO_BASE + 0x00)
+#define SPI_PP_FIFO_OP_BYTES_SHIFT 0
+#define SPI_PP_FIFO_OP_BYTES_MASK (0x3ff << SPI_PP_FIFO_OP_BYTES_SHIFT)
+#define SPI_PP_FIFO_OP_MBIT_SHIFT 11
+#define SPI_PP_FIFO_OP_MBIT_MASK (1 << SPI_PP_FIFO_OP_MBIT_SHIFT)
+#define SPI_PP_FIFO_OP_CODE_SHIFT 13
+#define SPI_PP_FIFO_OP_CODE_RW (1 << SPI_PP_FIFO_OP_CODE_SHIFT)
+#define SPI_PP_FIFO_OP_CODE_W (2 << SPI_PP_FIFO_OP_CODE_SHIFT)
+#define SPI_PP_FIFO_OP_CODE_R (3 << SPI_PP_FIFO_OP_CODE_SHIFT)
+
+struct bcm63xx_hsspi_priv {
+ void __iomem *regs;
+ ulong clk_rate;
+ uint8_t num_cs;
+ uint8_t cs_pols;
+ uint speed;
+};
+
+static int bcm63xx_hsspi_cs_info(struct udevice *bus, uint cs,
+ struct spi_cs_info *info)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(bus);
+
+ if (cs >= priv->num_cs) {
+ error("no cs %u\n", cs);
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int bcm63xx_hsspi_set_mode(struct udevice *bus, uint mode)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(bus);
+
+ /* clock polarity */
+ if (mode & SPI_CPOL)
+ setbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CLK_POL_MASK);
+ else
+ clrbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CLK_POL_MASK);
+
+ return 0;
+}
+
+static int bcm63xx_hsspi_set_speed(struct udevice *bus, uint speed)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(bus);
+
+ priv->speed = speed;
+
+ return 0;
+}
+
+static void bcm63xx_hsspi_claim_cs(struct bcm63xx_hsspi_priv *priv,
+ struct dm_spi_slave_platdata *plat)
+{
+ uint32_t clr, set;
+
+ /* profile clock */
+ set = DIV_ROUND_UP(priv->clk_rate, priv->speed);
+ set = DIV_ROUND_UP(2048, set);
+ set &= SPI_PFL_CLK_FREQ_MASK;
+ set |= SPI_PFL_CLK_RSTLOOP_MASK;
+ writel_be(set, priv->regs + SPI_PFL_CLK_REG(plat->cs));
+
+ /* profile signal */
+ set = 0;
+ clr = SPI_PFL_SIG_LAUNCHRIS_MASK |
+ SPI_PFL_SIG_LATCHRIS_MASK |
+ SPI_PFL_SIG_ASYNCIN_MASK;
+
+ /* latch/launch config */
+ if (plat->mode & SPI_CPHA)
+ set |= SPI_PFL_SIG_LAUNCHRIS_MASK;
+ else
+ set |= SPI_PFL_SIG_LATCHRIS_MASK;
+
+ /* async clk */
+ if (priv->speed > SPI_MAX_SYNC_CLOCK)
+ set |= SPI_PFL_SIG_ASYNCIN_MASK;
+
+ clrsetbits_be32(priv->regs + SPI_PFL_SIG_REG(plat->cs), clr, set);
+
+ /* global control */
+ set = 0;
+ clr = 0;
+
+ /* invert cs polarity */
+ if (priv->cs_pols & BIT(plat->cs))
+ clr |= BIT(plat->cs);
+ else
+ set |= BIT(plat->cs);
+
+ /* invert dummy cs polarity */
+ if (priv->cs_pols & BIT(!plat->cs))
+ clr |= BIT(!plat->cs);
+ else
+ set |= BIT(!plat->cs);
+
+ clrsetbits_be32(priv->regs + SPI_CTL_REG, clr, set);
+}
+
+static void bcm63xx_hsspi_release_cs(struct bcm63xx_hsspi_priv *priv)
+{
+ /* restore cs polarities */
+ clrsetbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CS_POL_MASK,
+ priv->cs_pols);
+}
+
+/*
+ * BCM63xx HSSPI driver doesn't allow keeping CS active between transfers
+ * because they are controlled by HW.
+ * However, it provides a mechanism to prepend write transfers prior to read
+ * transfers (with a maximum prepend of 15 bytes), which is usually enough for
+ * SPI-connected flashes since reading requires prepending a write transfer of
+ * 5 bytes. On the other hand it also provides a way to invert each CS
+ * polarity, not only between transfers like the older BCM63xx SPI driver, but
+ * also the rest of the time.
+ *
+ * Instead of using the prepend mechanism, this implementation inverts the
+ * polarity of both the desired CS and another dummy CS when the bus is
+ * claimed. This way, the dummy CS is restored to its inactive value when
+ * transfers are issued and the desired CS is preserved in its active value
+ * all the time. This hack is also used in the upstream linux driver and
+ * allows keeping CS active between trasnfers even if the HW doesn't give
+ * this possibility.
+ */
+static int bcm63xx_hsspi_xfer(struct udevice *dev, unsigned int bitlen,
+ const void *dout, void *din, unsigned long flags)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev->parent);
+ struct dm_spi_slave_platdata *plat = dev_get_parent_platdata(dev);
+ size_t data_bytes = bitlen / 8;
+ size_t step_size = SPI_PP_FIFO_SIZE;
+ uint16_t opcode = 0;
+ uint32_t val;
+ const uint8_t *tx = dout;
+ uint8_t *rx = din;
+
+ if (flags & SPI_XFER_BEGIN)
+ bcm63xx_hsspi_claim_cs(priv, plat);
+
+ /* fifo operation */
+ if (tx && rx)
+ opcode = SPI_PP_FIFO_OP_CODE_RW;
+ else if (rx)
+ opcode = SPI_PP_FIFO_OP_CODE_R;
+ else if (tx)
+ opcode = SPI_PP_FIFO_OP_CODE_W;
+
+ if (opcode != SPI_PP_FIFO_OP_CODE_R)
+ step_size -= SPI_PP_FIFO_OP_SIZE;
+
+ /* dual mode */
+ if ((opcode == SPI_PP_FIFO_OP_CODE_R && plat->mode == SPI_RX_DUAL) ||
+ (opcode == SPI_PP_FIFO_OP_CODE_W && plat->mode == SPI_TX_DUAL))
+ opcode |= SPI_PP_FIFO_OP_MBIT_MASK;
+
+ /* profile mode */
+ val = SPI_PFL_MODE_FILL_MASK |
+ SPI_PFL_MODE_MDRDSZ_MASK |
+ SPI_PFL_MODE_MDWRSZ_MASK;
+ if (plat->mode & SPI_3WIRE)
+ val |= SPI_PFL_MODE_3WIRE_MASK;
+ writel_be(val, priv->regs + SPI_PFL_MODE_REG(plat->cs));
+
+ /* transfer loop */
+ while (data_bytes > 0) {
+ size_t curr_step = min(step_size, data_bytes);
+
+ /* copy tx data */
+ if (tx) {
+ memcpy_toio(priv->regs + SPI_PP_FIFO_BASE +
+ SPI_PP_FIFO_OP_SIZE, tx, curr_step);
+ tx += curr_step;
+ }
+
+ /* set fifo operation */
+ writew_be(opcode | (curr_step & SPI_PP_FIFO_OP_BYTES_MASK),
+ priv->regs + SPI_PP_FIFO_OP_REG);
+
+ /* issue the transfer */
+ val = SPI_PP_CMD_OP_START;
+ val |= (plat->cs << SPI_PP_CMD_PFL_SHIFT) &
+ SPI_PP_CMD_PFL_MASK;
+ val |= (!plat->cs << SPI_PP_CMD_SLAVE_SHIFT) &
+ SPI_PP_CMD_SLAVE_MASK;
+ writel_be(val, priv->regs + SPI_PP_CMD_REG);
+
+ /* wait for completion */
+ do {
+ /* check ping-pong status */
+ val = readl_be(priv->regs + SPI_PP_STAT_REG);
+
+ /* transfer completed */
+ if (!(val & SPI_PP_STAT_SRCBUSY_MASK))
+ break;
+ } while (1);
+
+ /* copy rx data */
+ if (rx) {
+ memcpy_fromio(rx, priv->regs + SPI_PP_FIFO_BASE,
+ curr_step);
+ rx += curr_step;
+ }
+
+ data_bytes -= curr_step;
+ }
+
+ if (flags & SPI_XFER_END)
+ bcm63xx_hsspi_release_cs(priv);
+
+ return 0;
+}
+
+static const struct dm_spi_ops bcm63xx_hsspi_ops = {
+ .cs_info = bcm63xx_hsspi_cs_info,
+ .set_mode = bcm63xx_hsspi_set_mode,
+ .set_speed = bcm63xx_hsspi_set_speed,
+ .xfer = bcm63xx_hsspi_xfer,
+};
+
+static const struct udevice_id bcm63xx_hsspi_ids[] = {
+ { .compatible = "brcm,bcm6328-hsspi", },
+ { /* sentinel */ }
+};
+
+static int bcm63xx_hsspi_child_pre_probe(struct udevice *dev)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev->parent);
+ struct dm_spi_slave_platdata *plat = dev_get_parent_platdata(dev);
+
+ /* check cs */
+ if (plat->cs >= priv->num_cs) {
+ error("no cs %u\n", plat->cs);
+ return -ENODEV;
+ }
+
+ /* cs polarity */
+ if (plat->mode & SPI_CS_HIGH)
+ priv->cs_pols |= BIT(plat->cs);
+ else
+ priv->cs_pols &= ~BIT(plat->cs);
+
+ return 0;
+}
+
+static int bcm63xx_hsspi_probe(struct udevice *dev)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev);
+ struct reset_ctl rst_ctl;
+ struct clk clk;
+ fdt_addr_t addr;
+ fdt_size_t size;
+ int ret;
+
+ addr = devfdt_get_addr_size_index(dev, 0, &size);
+ if (addr == FDT_ADDR_T_NONE)
+ return -EINVAL;
+
+ priv->regs = ioremap(addr, size);
+ priv->num_cs = fdtdec_get_uint(gd->fdt_blob, dev_of_offset(dev),
+ "num-cs", 8);
+
+ /* enable clock */
+ ret = clk_get_by_name(dev, "hsspi", &clk);
+ if (ret < 0)
+ return ret;
+
+ ret = clk_enable(&clk);
+ if (ret < 0)
+ return ret;
+
+ ret = clk_free(&clk);
+ if (ret < 0)
+ return ret;
+
+ /* get clock rate */
+ ret = clk_get_by_name(dev, "pll", &clk);
+ if (ret < 0)
+ return ret;
+
+ priv->clk_rate = clk_get_rate(&clk);
+
+ ret = clk_free(&clk);
+ if (ret < 0)
+ return ret;
+
+ /* perform reset */
+ ret = reset_get_by_index(dev, 0, &rst_ctl);
+ if (ret < 0)
+ return ret;
+
+ ret = reset_deassert(&rst_ctl);
+ if (ret < 0)
+ return ret;
+
+ ret = reset_free(&rst_ctl);
+ if (ret < 0)
+ return ret;
+
+ /* initialize hardware */
+ writel_be(0, priv->regs + SPI_IR_MASK_REG);
+
+ /* clear pending interrupts */
+ writel_be(SPI_IR_CLEAR_ALL, priv->regs + SPI_IR_STAT_REG);
+
+ /* enable clk gate */
+ setbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CLK_GATE_MASK);
+
+ /* read default cs polarities */
+ priv->cs_pols = readl_be(priv->regs + SPI_CTL_REG) &
+ SPI_CTL_CS_POL_MASK;
+
+ return 0;
+}
+
+U_BOOT_DRIVER(bcm63xx_hsspi) = {
+ .name = "bcm63xx_hsspi",
+ .id = UCLASS_SPI,
+ .of_match = bcm63xx_hsspi_ids,
+ .ops = &bcm63xx_hsspi_ops,
+ .priv_auto_alloc_size = sizeof(struct bcm63xx_hsspi_priv),
+ .child_pre_probe = bcm63xx_hsspi_child_pre_probe,
+ .probe = bcm63xx_hsspi_probe,
+};
--
2.11.0
^ permalink raw reply related [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v4 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328
2017-07-30 12:14 ` [U-Boot] [PATCH v4 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
2017-07-30 12:14 ` [U-Boot] [PATCH v4 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
@ 2017-07-30 12:14 ` Álvaro Fernández Rojas
2017-07-30 12:14 ` [U-Boot] [PATCH v4 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268 Álvaro Fernández Rojas
2017-07-30 12:14 ` [U-Boot] [PATCH v4 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un Álvaro Fernández Rojas
3 siblings, 0 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-07-30 12:14 UTC (permalink / raw)
To: u-boot
This driver manages the SPI controller present on this SoC.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
---
v4: no changes
v3: no changes
v2: no changes
arch/mips/dts/brcm,bcm6328.dtsi | 24 ++++++++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/arch/mips/dts/brcm,bcm6328.dtsi b/arch/mips/dts/brcm,bcm6328.dtsi
index a996075743..67d9278be4 100644
--- a/arch/mips/dts/brcm,bcm6328.dtsi
+++ b/arch/mips/dts/brcm,bcm6328.dtsi
@@ -13,6 +13,10 @@
/ {
compatible = "brcm,bcm6328";
+ aliases {
+ spi0 = &spi;
+ };
+
cpus {
reg = <0x10000000 0x4>;
#address-cells = <1>;
@@ -40,6 +44,12 @@
#size-cells = <1>;
u-boot,dm-pre-reloc;
+ hsspi_pll: hsspi-pll {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <133333333>;
+ };
+
periph_osc: periph-osc {
compatible = "fixed-clock";
#clock-cells = <0>;
@@ -123,6 +133,20 @@
status = "disabled";
};
+ spi: spi at 10001000 {
+ compatible = "brcm,bcm6328-hsspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x10001000 0x600>;
+ clocks = <&periph_clk BCM6328_CLK_HSSPI>, <&hsspi_pll>;
+ clock-names = "hsspi", "pll";
+ resets = <&periph_rst BCM6328_RST_SPI>;
+ spi-max-frequency = <33333334>;
+ num-cs = <3>;
+
+ status = "disabled";
+ };
+
periph_pwr: power-controller at 10001848 {
compatible = "brcm,bcm6328-power-domain";
reg = <0x10001848 0x4>;
--
2.11.0
^ permalink raw reply related [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v4 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268
2017-07-30 12:14 ` [U-Boot] [PATCH v4 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
2017-07-30 12:14 ` [U-Boot] [PATCH v4 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
2017-07-30 12:14 ` [U-Boot] [PATCH v4 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328 Álvaro Fernández Rojas
@ 2017-07-30 12:14 ` Álvaro Fernández Rojas
2017-07-30 12:14 ` [U-Boot] [PATCH v4 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un Álvaro Fernández Rojas
3 siblings, 0 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-07-30 12:14 UTC (permalink / raw)
To: u-boot
This driver manages the high speed SPI controller present on this SoC.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
---
v4: no changes
v3: no changes
v2: no changes
arch/mips/dts/brcm,bcm63268.dtsi | 21 +++++++++++++++++++++
1 file changed, 21 insertions(+)
diff --git a/arch/mips/dts/brcm,bcm63268.dtsi b/arch/mips/dts/brcm,bcm63268.dtsi
index 6e3d9c3820..4d4e36cccc 100644
--- a/arch/mips/dts/brcm,bcm63268.dtsi
+++ b/arch/mips/dts/brcm,bcm63268.dtsi
@@ -15,6 +15,7 @@
aliases {
spi0 = &lsspi;
+ spi1 = &hsspi;
};
cpus {
@@ -44,6 +45,12 @@
#size-cells = <1>;
u-boot,dm-pre-reloc;
+ hsspi_pll: hsspi-pll {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <400000000>;
+ };
+
periph_osc: periph-osc {
compatible = "fixed-clock";
#clock-cells = <0>;
@@ -153,6 +160,20 @@
status = "disabled";
};
+ hsspi: spi at 10001000 {
+ compatible = "brcm,bcm6328-hsspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x10001000 0x600>;
+ clocks = <&periph_clk BCM63268_CLK_HSSPI>, <&hsspi_pll>;
+ clock-names = "hsspi", "pll";
+ resets = <&periph_rst BCM63268_RST_SPI>;
+ spi-max-frequency = <50000000>;
+ num-cs = <8>;
+
+ status = "disabled";
+ };
+
leds: led-controller at 10001900 {
compatible = "brcm,bcm6328-leds";
reg = <0x10001900 0x24>;
--
2.11.0
^ permalink raw reply related [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v4 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un
2017-07-30 12:14 ` [U-Boot] [PATCH v4 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
` (2 preceding siblings ...)
2017-07-30 12:14 ` [U-Boot] [PATCH v4 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268 Álvaro Fernández Rojas
@ 2017-07-30 12:14 ` Álvaro Fernández Rojas
3 siblings, 0 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-07-30 12:14 UTC (permalink / raw)
To: u-boot
It's a Macronix (mx25l12805d) 16 MB SPI flash.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
---
v4: Sync with master.
v3: switch to CONFIG_BCM63XX_HSSPI
v2: no changes
arch/mips/dts/comtrend,ar-5387un.dts | 12 ++++++++++++
configs/comtrend_ar5387un_ram_defconfig | 8 ++++++++
2 files changed, 20 insertions(+)
diff --git a/arch/mips/dts/comtrend,ar-5387un.dts b/arch/mips/dts/comtrend,ar-5387un.dts
index 73f2b49b76..6067881a78 100644
--- a/arch/mips/dts/comtrend,ar-5387un.dts
+++ b/arch/mips/dts/comtrend,ar-5387un.dts
@@ -51,6 +51,18 @@
};
};
+&spi {
+ status = "okay";
+
+ spi-flash at 0 {
+ compatible = "spi-flash";
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <33333334>;
+ };
+};
+
&uart0 {
u-boot,dm-pre-reloc;
status = "okay";
diff --git a/configs/comtrend_ar5387un_ram_defconfig b/configs/comtrend_ar5387un_ram_defconfig
index f856752663..cc8626f829 100644
--- a/configs/comtrend_ar5387un_ram_defconfig
+++ b/configs/comtrend_ar5387un_ram_defconfig
@@ -42,3 +42,11 @@ CONFIG_RESET_BCM6345=y
# CONFIG_SPL_SERIAL_PRESENT is not set
CONFIG_DM_SERIAL=y
CONFIG_BCM6345_SERIAL=y
+CONFIG_BCM63XX_HSSPI=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_MTD=y
+CONFIG_SPI_FLASH_MACRONIX=y
--
2.11.0
^ permalink raw reply related [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v4 1/4] dm: spi: add BCM63xx HSSPI driver
2017-07-30 12:14 ` [U-Boot] [PATCH v4 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
@ 2017-08-11 9:42 ` Jagan Teki
2017-12-26 13:20 ` Álvaro Fernández Rojas
0 siblings, 1 reply; 45+ messages in thread
From: Jagan Teki @ 2017-08-11 9:42 UTC (permalink / raw)
To: u-boot
On Sun, Jul 30, 2017 at 5:44 PM, Álvaro Fernández Rojas
<noltari@gmail.com> wrote:
> This driver is a simplified version of linux/drivers/spi/spi-bcm63xx-hsspi.c
>
> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
> Reviewed-by: Simon Glass <sjg@chromium.org>
> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
> ---
> v4: no changes.
> v3: Switch to CONFIG_BCM63XX_HSSPI and rebase on top of SPI v4.
> v2: Introduce changes suggested by Simon Glass:
> - Split bcm63xx_hsspi_xfer() into smaller functions.
> - Check possible clock errors.
> - Check possible reset errors.
> - Switch to devfdt_get_addr_size_index().
> - Use setbits32_be() for clock gate.
>
> drivers/spi/Kconfig | 8 +
> drivers/spi/Makefile | 1 +
> drivers/spi/bcm63xx_hsspi.c | 413 ++++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 422 insertions(+)
> create mode 100644 drivers/spi/bcm63xx_hsspi.c
>
> diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
> index 511643607b..97c3cb6103 100644
> --- a/drivers/spi/Kconfig
> +++ b/drivers/spi/Kconfig
> @@ -40,6 +40,14 @@ config ATMEL_SPI
> many AT91 (ARM) chips. This driver can be used to access
> the SPI Flash, such as AT25DF321.
>
> +config BCM63XX_HSSPI
> + bool "BCM63XX HSSPI driver"
> + depends on ARCH_BMIPS
> + help
> + Enable the BCM6328 HSSPI driver. This driver can be used to
> + access the SPI NOR flash on platforms embedding this Broadcom
> + SPI core.
> +
> config BCM63XX_SPI
> bool "BCM6348 SPI driver"
> depends on ARCH_BMIPS
> diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
> index d9802dd8c3..fefafbe333 100644
> --- a/drivers/spi/Makefile
> +++ b/drivers/spi/Makefile
> @@ -19,6 +19,7 @@ obj-$(CONFIG_ALTERA_SPI) += altera_spi.o
> obj-$(CONFIG_ATH79_SPI) += ath79_spi.o
> obj-$(CONFIG_ATMEL_DATAFLASH_SPI) += atmel_dataflash_spi.o
> obj-$(CONFIG_ATMEL_SPI) += atmel_spi.o
> +obj-$(CONFIG_BCM63XX_HSSPI) += bcm63xx_hsspi.o
> obj-$(CONFIG_BCM63XX_SPI) += bcm63xx_spi.o
> obj-$(CONFIG_CADENCE_QSPI) += cadence_qspi.o cadence_qspi_apb.o
> obj-$(CONFIG_CF_SPI) += cf_spi.o
> diff --git a/drivers/spi/bcm63xx_hsspi.c b/drivers/spi/bcm63xx_hsspi.c
> new file mode 100644
> index 0000000000..538c4ec4fe
> --- /dev/null
> +++ b/drivers/spi/bcm63xx_hsspi.c
> @@ -0,0 +1,413 @@
> +/*
> + * Copyright (C) 2017 Álvaro Fernández Rojas <noltari@gmail.com>
> + *
> + * Derived from linux/drivers/spi/spi-bcm63xx-hsspi.c:
> + * Copyright (C) 2000-2010 Broadcom Corporation
> + * Copyright (C) 2012-2013 Jonas Gorski <jogo@openwrt.org>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <clk.h>
> +#include <dm.h>
> +#include <spi.h>
> +#include <reset.h>
> +#include <asm/io.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +#define SPI_PP_SEL 0
> +
> +#define SPI_MAX_SYNC_CLOCK 30000000
> +
> +/* SPI Control register */
> +#define SPI_CTL_REG 0x000
> +#define SPI_CTL_CS_POL_SHIFT 0
> +#define SPI_CTL_CS_POL_MASK (0xff << SPI_CTL_CS_POL_SHIFT)
> +#define SPI_CTL_CLK_GATE_SHIFT 16
> +#define SPI_CTL_CLK_GATE_MASK (1 << SPI_CTL_CLK_GATE_SHIFT)
> +#define SPI_CTL_CLK_POL_SHIFT 17
> +#define SPI_CTL_CLK_POL_MASK (1 << SPI_CTL_CLK_POL_SHIFT)
> +
> +/* SPI Interrupts registers */
> +#define SPI_IR_STAT_REG 0x008
> +#define SPI_IR_ST_MASK_REG 0x00c
> +#define SPI_IR_MASK_REG 0x010
> +
> +#define SPI_IR_CLEAR_ALL 0xff001f1f
> +
> +/* SPI Ping-Pong Command registers */
> +#define SPI_PP_CMD_REG (0x080 + (0x40 * (SPI_PP_SEL)) + 0x00)
> +#define SPI_PP_CMD_OP_SHIFT 0
> +#define SPI_PP_CMD_OP_START (0x1 << SPI_PP_CMD_OP_SHIFT)
> +#define SPI_PP_CMD_PFL_SHIFT 8
> +#define SPI_PP_CMD_PFL_MASK (0x7 << SPI_PP_CMD_PFL_SHIFT)
> +#define SPI_PP_CMD_SLAVE_SHIFT 12
> +#define SPI_PP_CMD_SLAVE_MASK (0x7 << SPI_PP_CMD_SLAVE_SHIFT)
> +
> +/* SPI Ping-Pong Status registers */
> +#define SPI_PP_STAT_REG (0x080 + (0x40 * (SPI_PP_SEL)) + 0x04)
> +#define SPI_PP_STAT_SRCBUSY_SHIFT 1
> +#define SPI_PP_STAT_SRCBUSY_MASK (1 << SPI_PP_STAT_SRCBUSY_SHIFT)
> +
> +/* SPI Profile Clock registers */
> +#define SPI_PFL_CLK_REG(x) (0x100 + (0x20 * (x)) + 0x00)
> +#define SPI_PFL_CLK_FREQ_SHIFT 0
> +#define SPI_PFL_CLK_FREQ_MASK (0x3fff << SPI_PFL_CLK_FREQ_SHIFT)
> +#define SPI_PFL_CLK_RSTLOOP_SHIFT 15
> +#define SPI_PFL_CLK_RSTLOOP_MASK (1 << SPI_PFL_CLK_RSTLOOP_SHIFT)
> +
> +/* SPI Profile Signal registers */
> +#define SPI_PFL_SIG_REG(x) (0x100 + (0x20 * (x)) + 0x04)
> +#define SPI_PFL_SIG_LATCHRIS_SHIFT 12
> +#define SPI_PFL_SIG_LATCHRIS_MASK (1 << SPI_PFL_SIG_LATCHRIS_SHIFT)
> +#define SPI_PFL_SIG_LAUNCHRIS_SHIFT 13
> +#define SPI_PFL_SIG_LAUNCHRIS_MASK (1 << SPI_PFL_SIG_LAUNCHRIS_SHIFT)
> +#define SPI_PFL_SIG_ASYNCIN_SHIFT 16
> +#define SPI_PFL_SIG_ASYNCIN_MASK (1 << SPI_PFL_SIG_ASYNCIN_SHIFT)
> +
> +/* SPI Profile Mode registers */
> +#define SPI_PFL_MODE_REG(x) (0x100 + (0x20 * (x)) + 0x08)
> +#define SPI_PFL_MODE_FILL_SHIFT 0
> +#define SPI_PFL_MODE_FILL_MASK (0xff << SPI_PFL_MODE_FILL_SHIFT)
> +#define SPI_PFL_MODE_MDRDSZ_SHIFT 16
> +#define SPI_PFL_MODE_MDRDSZ_MASK (1 << SPI_PFL_MODE_MDRDSZ_SHIFT)
> +#define SPI_PFL_MODE_MDWRSZ_SHIFT 18
> +#define SPI_PFL_MODE_MDWRSZ_MASK (1 << SPI_PFL_MODE_MDWRSZ_SHIFT)
> +#define SPI_PFL_MODE_3WIRE_SHIFT 20
> +#define SPI_PFL_MODE_3WIRE_MASK (1 << SPI_PFL_MODE_3WIRE_SHIFT)
> +
> +/* SPI Ping-Pong FIFO registers */
> +#define SPI_PP_FIFO_SIZE 0x200
> +#define SPI_PP_FIFO_BASE (0x200 + \
> + (SPI_PP_FIFO_SIZE * SPI_PP_SEL))
> +
> +/* SPI Ping-Pong FIFO OP register */
> +#define SPI_PP_FIFO_OP_SIZE 0x2
> +#define SPI_PP_FIFO_OP_REG (SPI_PP_FIFO_BASE + 0x00)
> +#define SPI_PP_FIFO_OP_BYTES_SHIFT 0
> +#define SPI_PP_FIFO_OP_BYTES_MASK (0x3ff << SPI_PP_FIFO_OP_BYTES_SHIFT)
> +#define SPI_PP_FIFO_OP_MBIT_SHIFT 11
> +#define SPI_PP_FIFO_OP_MBIT_MASK (1 << SPI_PP_FIFO_OP_MBIT_SHIFT)
> +#define SPI_PP_FIFO_OP_CODE_SHIFT 13
> +#define SPI_PP_FIFO_OP_CODE_RW (1 << SPI_PP_FIFO_OP_CODE_SHIFT)
> +#define SPI_PP_FIFO_OP_CODE_W (2 << SPI_PP_FIFO_OP_CODE_SHIFT)
> +#define SPI_PP_FIFO_OP_CODE_R (3 << SPI_PP_FIFO_OP_CODE_SHIFT)
> +
> +struct bcm63xx_hsspi_priv {
> + void __iomem *regs;
> + ulong clk_rate;
> + uint8_t num_cs;
> + uint8_t cs_pols;
> + uint speed;
> +};
> +
> +static int bcm63xx_hsspi_cs_info(struct udevice *bus, uint cs,
> + struct spi_cs_info *info)
> +{
> + struct bcm63xx_hsspi_priv *priv = dev_get_priv(bus);
> +
> + if (cs >= priv->num_cs) {
> + error("no cs %u\n", cs);
> + return -ENODEV;
> + }
> +
> + return 0;
> +}
> +
> +static int bcm63xx_hsspi_set_mode(struct udevice *bus, uint mode)
> +{
> + struct bcm63xx_hsspi_priv *priv = dev_get_priv(bus);
> +
> + /* clock polarity */
> + if (mode & SPI_CPOL)
> + setbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CLK_POL_MASK);
> + else
> + clrbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CLK_POL_MASK);
> +
> + return 0;
> +}
> +
> +static int bcm63xx_hsspi_set_speed(struct udevice *bus, uint speed)
> +{
> + struct bcm63xx_hsspi_priv *priv = dev_get_priv(bus);
> +
> + priv->speed = speed;
> +
> + return 0;
> +}
> +
> +static void bcm63xx_hsspi_claim_cs(struct bcm63xx_hsspi_priv *priv,
> + struct dm_spi_slave_platdata *plat)
> +{
> + uint32_t clr, set;
> +
> + /* profile clock */
> + set = DIV_ROUND_UP(priv->clk_rate, priv->speed);
> + set = DIV_ROUND_UP(2048, set);
> + set &= SPI_PFL_CLK_FREQ_MASK;
> + set |= SPI_PFL_CLK_RSTLOOP_MASK;
> + writel_be(set, priv->regs + SPI_PFL_CLK_REG(plat->cs));
> +
> + /* profile signal */
> + set = 0;
> + clr = SPI_PFL_SIG_LAUNCHRIS_MASK |
> + SPI_PFL_SIG_LATCHRIS_MASK |
> + SPI_PFL_SIG_ASYNCIN_MASK;
> +
> + /* latch/launch config */
> + if (plat->mode & SPI_CPHA)
> + set |= SPI_PFL_SIG_LAUNCHRIS_MASK;
> + else
> + set |= SPI_PFL_SIG_LATCHRIS_MASK;
> +
> + /* async clk */
> + if (priv->speed > SPI_MAX_SYNC_CLOCK)
> + set |= SPI_PFL_SIG_ASYNCIN_MASK;
> +
> + clrsetbits_be32(priv->regs + SPI_PFL_SIG_REG(plat->cs), clr, set);
This code should be one-time processed gather them as mode and speed
and move them into .set_mode and .set_speed. activate chipselect
should have SPI_CTL_REG reg update.
> +
> + /* global control */
> + set = 0;
> + clr = 0;
> +
> + /* invert cs polarity */
> + if (priv->cs_pols & BIT(plat->cs))
> + clr |= BIT(plat->cs);
> + else
> + set |= BIT(plat->cs);
> +
> + /* invert dummy cs polarity */
> + if (priv->cs_pols & BIT(!plat->cs))
> + clr |= BIT(!plat->cs);
> + else
> + set |= BIT(!plat->cs);
> +
> + clrsetbits_be32(priv->regs + SPI_CTL_REG, clr, set);
> +}
> +
> +static void bcm63xx_hsspi_release_cs(struct bcm63xx_hsspi_priv *priv)
> +{
> + /* restore cs polarities */
> + clrsetbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CS_POL_MASK,
> + priv->cs_pols);
> +}
I think we can have single function for activate and deactivate cs
like set_cs, try to group the same.
> +
> +/*
> + * BCM63xx HSSPI driver doesn't allow keeping CS active between transfers
> + * because they are controlled by HW.
> + * However, it provides a mechanism to prepend write transfers prior to read
> + * transfers (with a maximum prepend of 15 bytes), which is usually enough for
> + * SPI-connected flashes since reading requires prepending a write transfer of
> + * 5 bytes. On the other hand it also provides a way to invert each CS
> + * polarity, not only between transfers like the older BCM63xx SPI driver, but
> + * also the rest of the time.
> + *
> + * Instead of using the prepend mechanism, this implementation inverts the
> + * polarity of both the desired CS and another dummy CS when the bus is
> + * claimed. This way, the dummy CS is restored to its inactive value when
> + * transfers are issued and the desired CS is preserved in its active value
> + * all the time. This hack is also used in the upstream linux driver and
> + * allows keeping CS active between trasnfers even if the HW doesn't give
> + * this possibility.
> + */
> +static int bcm63xx_hsspi_xfer(struct udevice *dev, unsigned int bitlen,
> + const void *dout, void *din, unsigned long flags)
> +{
> + struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev->parent);
> + struct dm_spi_slave_platdata *plat = dev_get_parent_platdata(dev);
> + size_t data_bytes = bitlen / 8;
> + size_t step_size = SPI_PP_FIFO_SIZE;
Rename this macro which should resembles local driver name.
> + uint16_t opcode = 0;
> + uint32_t val;
> + const uint8_t *tx = dout;
> + uint8_t *rx = din;
> +
> + if (flags & SPI_XFER_BEGIN)
> + bcm63xx_hsspi_claim_cs(priv, plat);
_cs_activate better name than _claim_cs which usually preferred in
other drivers too.
> +
> + /* fifo operation */
> + if (tx && rx)
> + opcode = SPI_PP_FIFO_OP_CODE_RW;
these are not exactly SPI specific stuff, so drop SPI on macros
something like HSSPI_OP_READ_WRITE and similar to below macros as
well.
> + else if (rx)
> + opcode = SPI_PP_FIFO_OP_CODE_R;
> + else if (tx)
> + opcode = SPI_PP_FIFO_OP_CODE_W;
> +
> + if (opcode != SPI_PP_FIFO_OP_CODE_R)
> + step_size -= SPI_PP_FIFO_OP_SIZE;
> +
> + /* dual mode */
> + if ((opcode == SPI_PP_FIFO_OP_CODE_R && plat->mode == SPI_RX_DUAL) ||
> + (opcode == SPI_PP_FIFO_OP_CODE_W && plat->mode == SPI_TX_DUAL))
> + opcode |= SPI_PP_FIFO_OP_MBIT_MASK;
> +
> + /* profile mode */
> + val = SPI_PFL_MODE_FILL_MASK |
> + SPI_PFL_MODE_MDRDSZ_MASK |
> + SPI_PFL_MODE_MDWRSZ_MASK;
> + if (plat->mode & SPI_3WIRE)
> + val |= SPI_PFL_MODE_3WIRE_MASK;
> + writel_be(val, priv->regs + SPI_PFL_MODE_REG(plat->cs));
> +
> + /* transfer loop */
> + while (data_bytes > 0) {
> + size_t curr_step = min(step_size, data_bytes);
> +
> + /* copy tx data */
> + if (tx) {
> + memcpy_toio(priv->regs + SPI_PP_FIFO_BASE +
> + SPI_PP_FIFO_OP_SIZE, tx, curr_step);
> + tx += curr_step;
> + }
> +
> + /* set fifo operation */
> + writew_be(opcode | (curr_step & SPI_PP_FIFO_OP_BYTES_MASK),
> + priv->regs + SPI_PP_FIFO_OP_REG);
> +
> + /* issue the transfer */
> + val = SPI_PP_CMD_OP_START;
> + val |= (plat->cs << SPI_PP_CMD_PFL_SHIFT) &
> + SPI_PP_CMD_PFL_MASK;
> + val |= (!plat->cs << SPI_PP_CMD_SLAVE_SHIFT) &
> + SPI_PP_CMD_SLAVE_MASK;
> + writel_be(val, priv->regs + SPI_PP_CMD_REG);
> +
> + /* wait for completion */
> + do {
> + /* check ping-pong status */
> + val = readl_be(priv->regs + SPI_PP_STAT_REG);
> +
> + /* transfer completed */
> + if (!(val & SPI_PP_STAT_SRCBUSY_MASK))
> + break;
> + } while (1);
try to use wait_for_bit
> +
> + /* copy rx data */
> + if (rx) {
> + memcpy_fromio(rx, priv->regs + SPI_PP_FIFO_BASE,
> + curr_step);
> + rx += curr_step;
> + }
> +
> + data_bytes -= curr_step;
> + }
> +
> + if (flags & SPI_XFER_END)
> + bcm63xx_hsspi_release_cs(priv);
_deactivate_cs better name than _claim_cs which usually preferred in
other drivers too.
> +
> + return 0;
> +}
> +
> +static const struct dm_spi_ops bcm63xx_hsspi_ops = {
> + .cs_info = bcm63xx_hsspi_cs_info,
> + .set_mode = bcm63xx_hsspi_set_mode,
> + .set_speed = bcm63xx_hsspi_set_speed,
> + .xfer = bcm63xx_hsspi_xfer,
> +};
> +
> +static const struct udevice_id bcm63xx_hsspi_ids[] = {
> + { .compatible = "brcm,bcm6328-hsspi", },
> + { /* sentinel */ }
> +};
> +
> +static int bcm63xx_hsspi_child_pre_probe(struct udevice *dev)
> +{
> + struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev->parent);
> + struct dm_spi_slave_platdata *plat = dev_get_parent_platdata(dev);
> +
> + /* check cs */
> + if (plat->cs >= priv->num_cs) {
> + error("no cs %u\n", plat->cs);
> + return -ENODEV;
> + }
> +
> + /* cs polarity */
> + if (plat->mode & SPI_CS_HIGH)
> + priv->cs_pols |= BIT(plat->cs);
> + else
> + priv->cs_pols &= ~BIT(plat->cs);
> +
> + return 0;
> +}.cs
Why we need to child_probe here? becuase cs polarity mode check we can
do it on .set_mode and check cs we can do it on .cs_info
> +
> +static int bcm63xx_hsspi_probe(struct udevice *dev)
> +{
> + struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev);
> + struct reset_ctl rst_ctl;
> + struct clk clk;
> + fdt_addr_t addr;
> + fdt_size_t size;
> + int ret;
> +
> + addr = devfdt_get_addr_size_index(dev, 0, &size);
> + if (addr == FDT_ADDR_T_NONE)
> + return -EINVAL;
> +
> + priv->regs = ioremap(addr, size);
> + priv->num_cs = fdtdec_get_uint(gd->fdt_blob, dev_of_offset(dev),
> + "num-cs", 8);
> +
> + /* enable clock */
> + ret = clk_get_by_name(dev, "hsspi", &clk);
> + if (ret < 0)
> + return ret;
> +
> + ret = clk_enable(&clk);
> + if (ret < 0)
> + return ret;
> +
> + ret = clk_free(&clk);
> + if (ret < 0)
> + return ret;
> +
> + /* get clock rate */
> + ret = clk_get_by_name(dev, "pll", &clk);
> + if (ret < 0)
> + return ret;
> +
> + priv->clk_rate = clk_get_rate(&clk);
> +
> + ret = clk_free(&clk);
> + if (ret < 0)
> + return ret;
> +
> + /* perform reset */
> + ret = reset_get_by_index(dev, 0, &rst_ctl);
> + if (ret < 0)
> + return ret;
> +
> + ret = reset_deassert(&rst_ctl);
> + if (ret < 0)
> + return ret;
> +
> + ret = reset_free(&rst_ctl);
> + if (ret < 0)
> + return ret;
> +
> + /* initialize hardware */
> + writel_be(0, priv->regs + SPI_IR_MASK_REG);
> +
> + /* clear pending interrupts */
> + writel_be(SPI_IR_CLEAR_ALL, priv->regs + SPI_IR_STAT_REG);
> +
> + /* enable clk gate */
> + setbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CLK_GATE_MASK);
> +
> + /* read default cs polarities */
> + priv->cs_pols = readl_be(priv->regs + SPI_CTL_REG) &
> + SPI_CTL_CS_POL_MASK;
> +
> + return 0;
> +}
> +
> +U_BOOT_DRIVER(bcm63xx_hsspi) = {
> + .name = "bcm63xx_hsspi",
> + .id = UCLASS_SPI,
> + .of_match = bcm63xx_hsspi_ids,
> + .ops = &bcm63xx_hsspi_ops,
> + .priv_auto_alloc_size = sizeof(struct bcm63xx_hsspi_priv),
> + .child_pre_probe = bcm63xx_hsspi_child_pre_probe,
> + .probe = bcm63xx_hsspi_probe,
> +};
> --
> 2.11.0
>
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v4 1/4] dm: spi: add BCM63xx HSSPI driver
2017-08-11 9:42 ` Jagan Teki
@ 2017-12-26 13:20 ` Álvaro Fernández Rojas
0 siblings, 0 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2017-12-26 13:20 UTC (permalink / raw)
To: u-boot
Hi Jagan,
El 11/08/2017 a las 11:42, Jagan Teki escribió:
> On Sun, Jul 30, 2017 at 5:44 PM, Álvaro Fernández Rojas
> <noltari@gmail.com> wrote:
>> This driver is a simplified version of linux/drivers/spi/spi-bcm63xx-hsspi.c
>>
>> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
>> Reviewed-by: Simon Glass <sjg@chromium.org>
>> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
>> ---
>> v4: no changes.
>> v3: Switch to CONFIG_BCM63XX_HSSPI and rebase on top of SPI v4.
>> v2: Introduce changes suggested by Simon Glass:
>> - Split bcm63xx_hsspi_xfer() into smaller functions.
>> - Check possible clock errors.
>> - Check possible reset errors.
>> - Switch to devfdt_get_addr_size_index().
>> - Use setbits32_be() for clock gate.
>>
>> drivers/spi/Kconfig | 8 +
>> drivers/spi/Makefile | 1 +
>> drivers/spi/bcm63xx_hsspi.c | 413 ++++++++++++++++++++++++++++++++++++++++++++
>> 3 files changed, 422 insertions(+)
>> create mode 100644 drivers/spi/bcm63xx_hsspi.c
>>
>> diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
>> index 511643607b..97c3cb6103 100644
>> --- a/drivers/spi/Kconfig
>> +++ b/drivers/spi/Kconfig
>> @@ -40,6 +40,14 @@ config ATMEL_SPI
>> many AT91 (ARM) chips. This driver can be used to access
>> the SPI Flash, such as AT25DF321.
>>
>> +config BCM63XX_HSSPI
>> + bool "BCM63XX HSSPI driver"
>> + depends on ARCH_BMIPS
>> + help
>> + Enable the BCM6328 HSSPI driver. This driver can be used to
>> + access the SPI NOR flash on platforms embedding this Broadcom
>> + SPI core.
>> +
>> config BCM63XX_SPI
>> bool "BCM6348 SPI driver"
>> depends on ARCH_BMIPS
>> diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
>> index d9802dd8c3..fefafbe333 100644
>> --- a/drivers/spi/Makefile
>> +++ b/drivers/spi/Makefile
>> @@ -19,6 +19,7 @@ obj-$(CONFIG_ALTERA_SPI) += altera_spi.o
>> obj-$(CONFIG_ATH79_SPI) += ath79_spi.o
>> obj-$(CONFIG_ATMEL_DATAFLASH_SPI) += atmel_dataflash_spi.o
>> obj-$(CONFIG_ATMEL_SPI) += atmel_spi.o
>> +obj-$(CONFIG_BCM63XX_HSSPI) += bcm63xx_hsspi.o
>> obj-$(CONFIG_BCM63XX_SPI) += bcm63xx_spi.o
>> obj-$(CONFIG_CADENCE_QSPI) += cadence_qspi.o cadence_qspi_apb.o
>> obj-$(CONFIG_CF_SPI) += cf_spi.o
>> diff --git a/drivers/spi/bcm63xx_hsspi.c b/drivers/spi/bcm63xx_hsspi.c
>> new file mode 100644
>> index 0000000000..538c4ec4fe
>> --- /dev/null
>> +++ b/drivers/spi/bcm63xx_hsspi.c
>> @@ -0,0 +1,413 @@
>> +/*
>> + * Copyright (C) 2017 Álvaro Fernández Rojas <noltari@gmail.com>
>> + *
>> + * Derived from linux/drivers/spi/spi-bcm63xx-hsspi.c:
>> + * Copyright (C) 2000-2010 Broadcom Corporation
>> + * Copyright (C) 2012-2013 Jonas Gorski <jogo@openwrt.org>
>> + *
>> + * SPDX-License-Identifier: GPL-2.0+
>> + */
>> +
>> +#include <common.h>
>> +#include <clk.h>
>> +#include <dm.h>
>> +#include <spi.h>
>> +#include <reset.h>
>> +#include <asm/io.h>
>> +
>> +DECLARE_GLOBAL_DATA_PTR;
>> +
>> +#define SPI_PP_SEL 0
>> +
>> +#define SPI_MAX_SYNC_CLOCK 30000000
>> +
>> +/* SPI Control register */
>> +#define SPI_CTL_REG 0x000
>> +#define SPI_CTL_CS_POL_SHIFT 0
>> +#define SPI_CTL_CS_POL_MASK (0xff << SPI_CTL_CS_POL_SHIFT)
>> +#define SPI_CTL_CLK_GATE_SHIFT 16
>> +#define SPI_CTL_CLK_GATE_MASK (1 << SPI_CTL_CLK_GATE_SHIFT)
>> +#define SPI_CTL_CLK_POL_SHIFT 17
>> +#define SPI_CTL_CLK_POL_MASK (1 << SPI_CTL_CLK_POL_SHIFT)
>> +
>> +/* SPI Interrupts registers */
>> +#define SPI_IR_STAT_REG 0x008
>> +#define SPI_IR_ST_MASK_REG 0x00c
>> +#define SPI_IR_MASK_REG 0x010
>> +
>> +#define SPI_IR_CLEAR_ALL 0xff001f1f
>> +
>> +/* SPI Ping-Pong Command registers */
>> +#define SPI_PP_CMD_REG (0x080 + (0x40 * (SPI_PP_SEL)) + 0x00)
>> +#define SPI_PP_CMD_OP_SHIFT 0
>> +#define SPI_PP_CMD_OP_START (0x1 << SPI_PP_CMD_OP_SHIFT)
>> +#define SPI_PP_CMD_PFL_SHIFT 8
>> +#define SPI_PP_CMD_PFL_MASK (0x7 << SPI_PP_CMD_PFL_SHIFT)
>> +#define SPI_PP_CMD_SLAVE_SHIFT 12
>> +#define SPI_PP_CMD_SLAVE_MASK (0x7 << SPI_PP_CMD_SLAVE_SHIFT)
>> +
>> +/* SPI Ping-Pong Status registers */
>> +#define SPI_PP_STAT_REG (0x080 + (0x40 * (SPI_PP_SEL)) + 0x04)
>> +#define SPI_PP_STAT_SRCBUSY_SHIFT 1
>> +#define SPI_PP_STAT_SRCBUSY_MASK (1 << SPI_PP_STAT_SRCBUSY_SHIFT)
>> +
>> +/* SPI Profile Clock registers */
>> +#define SPI_PFL_CLK_REG(x) (0x100 + (0x20 * (x)) + 0x00)
>> +#define SPI_PFL_CLK_FREQ_SHIFT 0
>> +#define SPI_PFL_CLK_FREQ_MASK (0x3fff << SPI_PFL_CLK_FREQ_SHIFT)
>> +#define SPI_PFL_CLK_RSTLOOP_SHIFT 15
>> +#define SPI_PFL_CLK_RSTLOOP_MASK (1 << SPI_PFL_CLK_RSTLOOP_SHIFT)
>> +
>> +/* SPI Profile Signal registers */
>> +#define SPI_PFL_SIG_REG(x) (0x100 + (0x20 * (x)) + 0x04)
>> +#define SPI_PFL_SIG_LATCHRIS_SHIFT 12
>> +#define SPI_PFL_SIG_LATCHRIS_MASK (1 << SPI_PFL_SIG_LATCHRIS_SHIFT)
>> +#define SPI_PFL_SIG_LAUNCHRIS_SHIFT 13
>> +#define SPI_PFL_SIG_LAUNCHRIS_MASK (1 << SPI_PFL_SIG_LAUNCHRIS_SHIFT)
>> +#define SPI_PFL_SIG_ASYNCIN_SHIFT 16
>> +#define SPI_PFL_SIG_ASYNCIN_MASK (1 << SPI_PFL_SIG_ASYNCIN_SHIFT)
>> +
>> +/* SPI Profile Mode registers */
>> +#define SPI_PFL_MODE_REG(x) (0x100 + (0x20 * (x)) + 0x08)
>> +#define SPI_PFL_MODE_FILL_SHIFT 0
>> +#define SPI_PFL_MODE_FILL_MASK (0xff << SPI_PFL_MODE_FILL_SHIFT)
>> +#define SPI_PFL_MODE_MDRDSZ_SHIFT 16
>> +#define SPI_PFL_MODE_MDRDSZ_MASK (1 << SPI_PFL_MODE_MDRDSZ_SHIFT)
>> +#define SPI_PFL_MODE_MDWRSZ_SHIFT 18
>> +#define SPI_PFL_MODE_MDWRSZ_MASK (1 << SPI_PFL_MODE_MDWRSZ_SHIFT)
>> +#define SPI_PFL_MODE_3WIRE_SHIFT 20
>> +#define SPI_PFL_MODE_3WIRE_MASK (1 << SPI_PFL_MODE_3WIRE_SHIFT)
>> +
>> +/* SPI Ping-Pong FIFO registers */
>> +#define SPI_PP_FIFO_SIZE 0x200
>> +#define SPI_PP_FIFO_BASE (0x200 + \
>> + (SPI_PP_FIFO_SIZE * SPI_PP_SEL))
>> +
>> +/* SPI Ping-Pong FIFO OP register */
>> +#define SPI_PP_FIFO_OP_SIZE 0x2
>> +#define SPI_PP_FIFO_OP_REG (SPI_PP_FIFO_BASE + 0x00)
>> +#define SPI_PP_FIFO_OP_BYTES_SHIFT 0
>> +#define SPI_PP_FIFO_OP_BYTES_MASK (0x3ff << SPI_PP_FIFO_OP_BYTES_SHIFT)
>> +#define SPI_PP_FIFO_OP_MBIT_SHIFT 11
>> +#define SPI_PP_FIFO_OP_MBIT_MASK (1 << SPI_PP_FIFO_OP_MBIT_SHIFT)
>> +#define SPI_PP_FIFO_OP_CODE_SHIFT 13
>> +#define SPI_PP_FIFO_OP_CODE_RW (1 << SPI_PP_FIFO_OP_CODE_SHIFT)
>> +#define SPI_PP_FIFO_OP_CODE_W (2 << SPI_PP_FIFO_OP_CODE_SHIFT)
>> +#define SPI_PP_FIFO_OP_CODE_R (3 << SPI_PP_FIFO_OP_CODE_SHIFT)
>> +
>> +struct bcm63xx_hsspi_priv {
>> + void __iomem *regs;
>> + ulong clk_rate;
>> + uint8_t num_cs;
>> + uint8_t cs_pols;
>> + uint speed;
>> +};
>> +
>> +static int bcm63xx_hsspi_cs_info(struct udevice *bus, uint cs,
>> + struct spi_cs_info *info)
>> +{
>> + struct bcm63xx_hsspi_priv *priv = dev_get_priv(bus);
>> +
>> + if (cs >= priv->num_cs) {
>> + error("no cs %u\n", cs);
>> + return -ENODEV;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int bcm63xx_hsspi_set_mode(struct udevice *bus, uint mode)
>> +{
>> + struct bcm63xx_hsspi_priv *priv = dev_get_priv(bus);
>> +
>> + /* clock polarity */
>> + if (mode & SPI_CPOL)
>> + setbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CLK_POL_MASK);
>> + else
>> + clrbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CLK_POL_MASK);
>> +
>> + return 0;
>> +}
>> +
>> +static int bcm63xx_hsspi_set_speed(struct udevice *bus, uint speed)
>> +{
>> + struct bcm63xx_hsspi_priv *priv = dev_get_priv(bus);
>> +
>> + priv->speed = speed;
>> +
>> + return 0;
>> +}
>> +
>> +static void bcm63xx_hsspi_claim_cs(struct bcm63xx_hsspi_priv *priv,
>> + struct dm_spi_slave_platdata *plat)
>> +{
>> + uint32_t clr, set;
>> +
>> + /* profile clock */
>> + set = DIV_ROUND_UP(priv->clk_rate, priv->speed);
>> + set = DIV_ROUND_UP(2048, set);
>> + set &= SPI_PFL_CLK_FREQ_MASK;
>> + set |= SPI_PFL_CLK_RSTLOOP_MASK;
>> + writel_be(set, priv->regs + SPI_PFL_CLK_REG(plat->cs));
>> +
>> + /* profile signal */
>> + set = 0;
>> + clr = SPI_PFL_SIG_LAUNCHRIS_MASK |
>> + SPI_PFL_SIG_LATCHRIS_MASK |
>> + SPI_PFL_SIG_ASYNCIN_MASK;
>> +
>> + /* latch/launch config */
>> + if (plat->mode & SPI_CPHA)
>> + set |= SPI_PFL_SIG_LAUNCHRIS_MASK;
>> + else
>> + set |= SPI_PFL_SIG_LATCHRIS_MASK;
>> +
>> + /* async clk */
>> + if (priv->speed > SPI_MAX_SYNC_CLOCK)
>> + set |= SPI_PFL_SIG_ASYNCIN_MASK;
>> +
>> + clrsetbits_be32(priv->regs + SPI_PFL_SIG_REG(plat->cs), clr, set);
> This code should be one-time processed gather them as mode and speed
> and move them into .set_mode and .set_speed. activate chipselect
> should have SPI_CTL_REG reg update.
I'm afraid I can't do that since both registers depend on the CS.
>
>> +
>> + /* global control */
>> + set = 0;
>> + clr = 0;
>> +
>> + /* invert cs polarity */
>> + if (priv->cs_pols & BIT(plat->cs))
>> + clr |= BIT(plat->cs);
>> + else
>> + set |= BIT(plat->cs);
>> +
>> + /* invert dummy cs polarity */
>> + if (priv->cs_pols & BIT(!plat->cs))
>> + clr |= BIT(!plat->cs);
>> + else
>> + set |= BIT(!plat->cs);
>> +
>> + clrsetbits_be32(priv->regs + SPI_CTL_REG, clr, set);
>> +}
>> +
>> +static void bcm63xx_hsspi_release_cs(struct bcm63xx_hsspi_priv *priv)
>> +{
>> + /* restore cs polarities */
>> + clrsetbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CS_POL_MASK,
>> + priv->cs_pols);
>> +}
> I think we can have single function for activate and deactivate cs
> like set_cs, try to group the same.
bcm63xx_hsspi_claim_cs needs to set more registers, so there's no point in grouping under a single set_cs function.
>
>> +
>> +/*
>> + * BCM63xx HSSPI driver doesn't allow keeping CS active between transfers
>> + * because they are controlled by HW.
>> + * However, it provides a mechanism to prepend write transfers prior to read
>> + * transfers (with a maximum prepend of 15 bytes), which is usually enough for
>> + * SPI-connected flashes since reading requires prepending a write transfer of
>> + * 5 bytes. On the other hand it also provides a way to invert each CS
>> + * polarity, not only between transfers like the older BCM63xx SPI driver, but
>> + * also the rest of the time.
>> + *
>> + * Instead of using the prepend mechanism, this implementation inverts the
>> + * polarity of both the desired CS and another dummy CS when the bus is
>> + * claimed. This way, the dummy CS is restored to its inactive value when
>> + * transfers are issued and the desired CS is preserved in its active value
>> + * all the time. This hack is also used in the upstream linux driver and
>> + * allows keeping CS active between trasnfers even if the HW doesn't give
>> + * this possibility.
>> + */
>> +static int bcm63xx_hsspi_xfer(struct udevice *dev, unsigned int bitlen,
>> + const void *dout, void *din, unsigned long flags)
>> +{
>> + struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev->parent);
>> + struct dm_spi_slave_platdata *plat = dev_get_parent_platdata(dev);
>> + size_t data_bytes = bitlen / 8;
>> + size_t step_size = SPI_PP_FIFO_SIZE;
> Rename this macro which should resembles local driver name.
OK.
>
>> + uint16_t opcode = 0;
>> + uint32_t val;
>> + const uint8_t *tx = dout;
>> + uint8_t *rx = din;
>> +
>> + if (flags & SPI_XFER_BEGIN)
>> + bcm63xx_hsspi_claim_cs(priv, plat);
> _cs_activate better name than _claim_cs which usually preferred in
> other drivers too.
OK.
>
>> +
>> + /* fifo operation */
>> + if (tx && rx)
>> + opcode = SPI_PP_FIFO_OP_CODE_RW;
> these are not exactly SPI specific stuff, so drop SPI on macros
> something like HSSPI_OP_READ_WRITE and similar to below macros as
> well.
OK.
>
>> + else if (rx)
>> + opcode = SPI_PP_FIFO_OP_CODE_R;
>> + else if (tx)
>> + opcode = SPI_PP_FIFO_OP_CODE_W;
>> +
>> + if (opcode != SPI_PP_FIFO_OP_CODE_R)
>> + step_size -= SPI_PP_FIFO_OP_SIZE;
>> +
>> + /* dual mode */
>> + if ((opcode == SPI_PP_FIFO_OP_CODE_R && plat->mode == SPI_RX_DUAL) ||
>> + (opcode == SPI_PP_FIFO_OP_CODE_W && plat->mode == SPI_TX_DUAL))
>> + opcode |= SPI_PP_FIFO_OP_MBIT_MASK;
>> +
>> + /* profile mode */
>> + val = SPI_PFL_MODE_FILL_MASK |
>> + SPI_PFL_MODE_MDRDSZ_MASK |
>> + SPI_PFL_MODE_MDWRSZ_MASK;
>> + if (plat->mode & SPI_3WIRE)
>> + val |= SPI_PFL_MODE_3WIRE_MASK;
>> + writel_be(val, priv->regs + SPI_PFL_MODE_REG(plat->cs));
>> +
>> + /* transfer loop */
>> + while (data_bytes > 0) {
>> + size_t curr_step = min(step_size, data_bytes);
>> +
>> + /* copy tx data */
>> + if (tx) {
>> + memcpy_toio(priv->regs + SPI_PP_FIFO_BASE +
>> + SPI_PP_FIFO_OP_SIZE, tx, curr_step);
>> + tx += curr_step;
>> + }
>> +
>> + /* set fifo operation */
>> + writew_be(opcode | (curr_step & SPI_PP_FIFO_OP_BYTES_MASK),
>> + priv->regs + SPI_PP_FIFO_OP_REG);
>> +
>> + /* issue the transfer */
>> + val = SPI_PP_CMD_OP_START;
>> + val |= (plat->cs << SPI_PP_CMD_PFL_SHIFT) &
>> + SPI_PP_CMD_PFL_MASK;
>> + val |= (!plat->cs << SPI_PP_CMD_SLAVE_SHIFT) &
>> + SPI_PP_CMD_SLAVE_MASK;
>> + writel_be(val, priv->regs + SPI_PP_CMD_REG);
>> +
>> + /* wait for completion */
>> + do {
>> + /* check ping-pong status */
>> + val = readl_be(priv->regs + SPI_PP_STAT_REG);
>> +
>> + /* transfer completed */
>> + if (!(val & SPI_PP_STAT_SRCBUSY_MASK))
>> + break;
>> + } while (1);
> try to use wait_for_bit
wait_for_bit_be?
https://gist.github.com/Noltari/8ab369cae5f8577255c81e16402b358e
>
>> +
>> + /* copy rx data */
>> + if (rx) {
>> + memcpy_fromio(rx, priv->regs + SPI_PP_FIFO_BASE,
>> + curr_step);
>> + rx += curr_step;
>> + }
>> +
>> + data_bytes -= curr_step;
>> + }
>> +
>> + if (flags & SPI_XFER_END)
>> + bcm63xx_hsspi_release_cs(priv);
> _deactivate_cs better name than _claim_cs which usually preferred in
> other drivers too.
OK.
>
>> +
>> + return 0;
>> +}
>> +
>> +static const struct dm_spi_ops bcm63xx_hsspi_ops = {
>> + .cs_info = bcm63xx_hsspi_cs_info,
>> + .set_mode = bcm63xx_hsspi_set_mode,
>> + .set_speed = bcm63xx_hsspi_set_speed,
>> + .xfer = bcm63xx_hsspi_xfer,
>> +};
>> +
>> +static const struct udevice_id bcm63xx_hsspi_ids[] = {
>> + { .compatible = "brcm,bcm6328-hsspi", },
>> + { /* sentinel */ }
>> +};
>> +
>> +static int bcm63xx_hsspi_child_pre_probe(struct udevice *dev)
>> +{
>> + struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev->parent);
>> + struct dm_spi_slave_platdata *plat = dev_get_parent_platdata(dev);
>> +
>> + /* check cs */
>> + if (plat->cs >= priv->num_cs) {
>> + error("no cs %u\n", plat->cs);
>> + return -ENODEV;
>> + }
>> +
>> + /* cs polarity */
>> + if (plat->mode & SPI_CS_HIGH)
>> + priv->cs_pols |= BIT(plat->cs);
>> + else
>> + priv->cs_pols &= ~BIT(plat->cs);
>> +
>> + return 0;
>> +}.cs
> Why we need to child_probe here? becuase cs polarity mode check we can
> do it on .set_mode and check cs we can do it on .cs_info
Because we need to know in advance if any of the existing SPI slaves
require changing CS polarity to high.
This is due to the prepend workaround:
/*
* BCM63xx HSSPI driver doesn't allow keeping CS active between transfers
* because they are controlled by HW.
* However, it provides a mechanism to prepend write transfers prior to read
* transfers (with a maximum prepend of 15 bytes), which is usually enough for
* SPI-connected flashes since reading requires prepending a write transfer of
* 5 bytes. On the other hand it also provides a way to invert each CS
* polarity, not only between transfers like the older BCM63xx SPI driver, but
* also the rest of the time.
*
* Instead of using the prepend mechanism, this implementation inverts the
* polarity of both the desired CS and another dummy CS when the bus is
* claimed. This way, the dummy CS is restored to its inactive value when
* transfers are issued and the desired CS is preserved in its active value
* all the time. This hack is also used in the upstream linux driver and
* allows keeping CS active between trasnfers even if the HW doesn't give
* this possibility.
*/
>
>> +
>> +static int bcm63xx_hsspi_probe(struct udevice *dev)
>> +{
>> + struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev);
>> + struct reset_ctl rst_ctl;
>> + struct clk clk;
>> + fdt_addr_t addr;
>> + fdt_size_t size;
>> + int ret;
>> +
>> + addr = devfdt_get_addr_size_index(dev, 0, &size);
>> + if (addr == FDT_ADDR_T_NONE)
>> + return -EINVAL;
>> +
>> + priv->regs = ioremap(addr, size);
>> + priv->num_cs = fdtdec_get_uint(gd->fdt_blob, dev_of_offset(dev),
>> + "num-cs", 8);
>> +
>> + /* enable clock */
>> + ret = clk_get_by_name(dev, "hsspi", &clk);
>> + if (ret < 0)
>> + return ret;
>> +
>> + ret = clk_enable(&clk);
>> + if (ret < 0)
>> + return ret;
>> +
>> + ret = clk_free(&clk);
>> + if (ret < 0)
>> + return ret;
>> +
>> + /* get clock rate */
>> + ret = clk_get_by_name(dev, "pll", &clk);
>> + if (ret < 0)
>> + return ret;
>> +
>> + priv->clk_rate = clk_get_rate(&clk);
>> +
>> + ret = clk_free(&clk);
>> + if (ret < 0)
>> + return ret;
>> +
>> + /* perform reset */
>> + ret = reset_get_by_index(dev, 0, &rst_ctl);
>> + if (ret < 0)
>> + return ret;
>> +
>> + ret = reset_deassert(&rst_ctl);
>> + if (ret < 0)
>> + return ret;
>> +
>> + ret = reset_free(&rst_ctl);
>> + if (ret < 0)
>> + return ret;
>> +
>> + /* initialize hardware */
>> + writel_be(0, priv->regs + SPI_IR_MASK_REG);
>> +
>> + /* clear pending interrupts */
>> + writel_be(SPI_IR_CLEAR_ALL, priv->regs + SPI_IR_STAT_REG);
>> +
>> + /* enable clk gate */
>> + setbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CLK_GATE_MASK);
>> +
>> + /* read default cs polarities */
>> + priv->cs_pols = readl_be(priv->regs + SPI_CTL_REG) &
>> + SPI_CTL_CS_POL_MASK;
>> +
>> + return 0;
>> +}
>> +
>> +U_BOOT_DRIVER(bcm63xx_hsspi) = {
>> + .name = "bcm63xx_hsspi",
>> + .id = UCLASS_SPI,
>> + .of_match = bcm63xx_hsspi_ids,
>> + .ops = &bcm63xx_hsspi_ops,
>> + .priv_auto_alloc_size = sizeof(struct bcm63xx_hsspi_priv),
>> + .child_pre_probe = bcm63xx_hsspi_child_pre_probe,
>> + .probe = bcm63xx_hsspi_probe,
>> +};
>> --
>> 2.11.0
>>
> thanks!
^ permalink raw reply [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v5 0/4] mips: bmips: add HSSPI support
2017-05-23 19:18 [U-Boot] [PATCH 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
` (6 preceding siblings ...)
2017-07-30 12:14 ` [U-Boot] [PATCH v4 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
@ 2018-01-15 18:45 ` Álvaro Fernández Rojas
2018-01-15 18:45 ` [U-Boot] [PATCH v5 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
` (3 more replies)
2018-01-20 1:13 ` [U-Boot] [PATCH v6 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
8 siblings, 4 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2018-01-15 18:45 UTC (permalink / raw)
To: u-boot
BCM63xx HSSPI controller has the same issue as BCM63xx SPI controller: it
doesn't allow keeping CS active between transfers.
However, this controller allows changing CS polarities, which is used in the
linux upstream driver to manage CS as desired.
v5: Introduce changes suggested by Jagan Teki:
- Rename SPI_PP_ macros.
- cs_activate instead of claim_cs.
- deactivate_cs instead of release_cs.
- Use wait_for_bit_be32 instead of infinite loop.
v4: Sync with master.
v3: Switch to CONFIG_BCM63XX_HSSPI and rebase on top of SPI v4.
v2: Introduce changes suggested by Simon Glass:
- Split bcm63xx_hsspi_xfer() into smaller functions.
- Check possible clock errors.
- Check possible reset errors.
- Switch to devfdt_get_addr_size_index().
- Use setbits32_be() for clock gate.
Álvaro Fernández Rojas (4):
dm: spi: add BCM63xx HSSPI driver
mips: bmips: add bcm63xx-hsspi driver support for BCM6328
mips: bmips: add bcm63xx-hsspi driver support for BCM63268
mips: bmips: enable the SPI flash on the Comtrend AR-5387un
arch/mips/dts/brcm,bcm63268.dtsi | 21 ++
arch/mips/dts/brcm,bcm6328.dtsi | 24 ++
arch/mips/dts/comtrend,ar-5387un.dts | 12 +
configs/comtrend_ar5387un_ram_defconfig | 8 +
drivers/spi/Kconfig | 8 +
drivers/spi/Makefile | 1 +
drivers/spi/bcm63xx_hsspi.c | 414 ++++++++++++++++++++++++++++++++
7 files changed, 488 insertions(+)
create mode 100644 drivers/spi/bcm63xx_hsspi.c
--
2.11.0
^ permalink raw reply [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v5 1/4] dm: spi: add BCM63xx HSSPI driver
2018-01-15 18:45 ` [U-Boot] [PATCH v5 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
@ 2018-01-15 18:45 ` Álvaro Fernández Rojas
2018-01-15 18:45 ` [U-Boot] [PATCH v5 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328 Álvaro Fernández Rojas
` (2 subsequent siblings)
3 siblings, 0 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2018-01-15 18:45 UTC (permalink / raw)
To: u-boot
This driver is a simplified version of linux/drivers/spi/spi-bcm63xx-hsspi.c
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
---
v5: Introduce changes suggested by Jagan Teki:
- Rename SPI_PP_ macros.
- cs_activate instead of claim_cs.
- deactivate_cs instead of release_cs.
- Use wait_for_bit_be32 instead of infinite loop.
v4: no changes.
v3: Switch to CONFIG_BCM63XX_HSSPI and rebase on top of SPI v4.
v2: Introduce changes suggested by Simon Glass:
- Split bcm63xx_hsspi_xfer() into smaller functions.
- Check possible clock errors.
- Check possible reset errors.
- Switch to devfdt_get_addr_size_index().
- Use setbits32_be() for clock gate.
drivers/spi/Kconfig | 8 +
drivers/spi/Makefile | 1 +
drivers/spi/bcm63xx_hsspi.c | 414 ++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 423 insertions(+)
create mode 100644 drivers/spi/bcm63xx_hsspi.c
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index ebc71c2e42..28ddcf85a3 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -40,6 +40,14 @@ config ATMEL_SPI
many AT91 (ARM) chips. This driver can be used to access
the SPI Flash, such as AT25DF321.
+config BCM63XX_HSSPI
+ bool "BCM63XX HSSPI driver"
+ depends on ARCH_BMIPS
+ help
+ Enable the BCM6328 HSSPI driver. This driver can be used to
+ access the SPI NOR flash on platforms embedding this Broadcom
+ SPI core.
+
config BCM63XX_SPI
bool "BCM6348 SPI driver"
depends on ARCH_BMIPS
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 5770b3f7cc..4b6000fd9a 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -18,6 +18,7 @@ endif
obj-$(CONFIG_ALTERA_SPI) += altera_spi.o
obj-$(CONFIG_ATH79_SPI) += ath79_spi.o
obj-$(CONFIG_ATMEL_SPI) += atmel_spi.o
+obj-$(CONFIG_BCM63XX_HSSPI) += bcm63xx_hsspi.o
obj-$(CONFIG_BCM63XX_SPI) += bcm63xx_spi.o
obj-$(CONFIG_CADENCE_QSPI) += cadence_qspi.o cadence_qspi_apb.o
obj-$(CONFIG_CF_SPI) += cf_spi.o
diff --git a/drivers/spi/bcm63xx_hsspi.c b/drivers/spi/bcm63xx_hsspi.c
new file mode 100644
index 0000000000..3393166a1e
--- /dev/null
+++ b/drivers/spi/bcm63xx_hsspi.c
@@ -0,0 +1,414 @@
+/*
+ * Copyright (C) 2017 Álvaro Fernández Rojas <noltari@gmail.com>
+ *
+ * Derived from linux/drivers/spi/spi-bcm63xx-hsspi.c:
+ * Copyright (C) 2000-2010 Broadcom Corporation
+ * Copyright (C) 2012-2013 Jonas Gorski <jogo@openwrt.org>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <clk.h>
+#include <dm.h>
+#include <spi.h>
+#include <reset.h>
+#include <wait_bit.h>
+#include <asm/io.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define HSSPI_PP 0
+
+#define SPI_MAX_SYNC_CLOCK 30000000
+
+/* SPI Control register */
+#define SPI_CTL_REG 0x000
+#define SPI_CTL_CS_POL_SHIFT 0
+#define SPI_CTL_CS_POL_MASK (0xff << SPI_CTL_CS_POL_SHIFT)
+#define SPI_CTL_CLK_GATE_SHIFT 16
+#define SPI_CTL_CLK_GATE_MASK (1 << SPI_CTL_CLK_GATE_SHIFT)
+#define SPI_CTL_CLK_POL_SHIFT 17
+#define SPI_CTL_CLK_POL_MASK (1 << SPI_CTL_CLK_POL_SHIFT)
+
+/* SPI Interrupts registers */
+#define SPI_IR_STAT_REG 0x008
+#define SPI_IR_ST_MASK_REG 0x00c
+#define SPI_IR_MASK_REG 0x010
+
+#define SPI_IR_CLEAR_ALL 0xff001f1f
+
+/* SPI Ping-Pong Command registers */
+#define SPI_CMD_REG (0x080 + (0x40 * (HSSPI_PP)) + 0x00)
+#define SPI_CMD_OP_SHIFT 0
+#define SPI_CMD_OP_START (0x1 << SPI_CMD_OP_SHIFT)
+#define SPI_CMD_PFL_SHIFT 8
+#define SPI_CMD_PFL_MASK (0x7 << SPI_CMD_PFL_SHIFT)
+#define SPI_CMD_SLAVE_SHIFT 12
+#define SPI_CMD_SLAVE_MASK (0x7 << SPI_CMD_SLAVE_SHIFT)
+
+/* SPI Ping-Pong Status registers */
+#define SPI_STAT_REG (0x080 + (0x40 * (HSSPI_PP)) + 0x04)
+#define SPI_STAT_SRCBUSY_SHIFT 1
+#define SPI_STAT_SRCBUSY_MASK (1 << SPI_STAT_SRCBUSY_SHIFT)
+
+/* SPI Profile Clock registers */
+#define SPI_PFL_CLK_REG(x) (0x100 + (0x20 * (x)) + 0x00)
+#define SPI_PFL_CLK_FREQ_SHIFT 0
+#define SPI_PFL_CLK_FREQ_MASK (0x3fff << SPI_PFL_CLK_FREQ_SHIFT)
+#define SPI_PFL_CLK_RSTLOOP_SHIFT 15
+#define SPI_PFL_CLK_RSTLOOP_MASK (1 << SPI_PFL_CLK_RSTLOOP_SHIFT)
+
+/* SPI Profile Signal registers */
+#define SPI_PFL_SIG_REG(x) (0x100 + (0x20 * (x)) + 0x04)
+#define SPI_PFL_SIG_LATCHRIS_SHIFT 12
+#define SPI_PFL_SIG_LATCHRIS_MASK (1 << SPI_PFL_SIG_LATCHRIS_SHIFT)
+#define SPI_PFL_SIG_LAUNCHRIS_SHIFT 13
+#define SPI_PFL_SIG_LAUNCHRIS_MASK (1 << SPI_PFL_SIG_LAUNCHRIS_SHIFT)
+#define SPI_PFL_SIG_ASYNCIN_SHIFT 16
+#define SPI_PFL_SIG_ASYNCIN_MASK (1 << SPI_PFL_SIG_ASYNCIN_SHIFT)
+
+/* SPI Profile Mode registers */
+#define SPI_PFL_MODE_REG(x) (0x100 + (0x20 * (x)) + 0x08)
+#define SPI_PFL_MODE_FILL_SHIFT 0
+#define SPI_PFL_MODE_FILL_MASK (0xff << SPI_PFL_MODE_FILL_SHIFT)
+#define SPI_PFL_MODE_MDRDSZ_SHIFT 16
+#define SPI_PFL_MODE_MDRDSZ_MASK (1 << SPI_PFL_MODE_MDRDSZ_SHIFT)
+#define SPI_PFL_MODE_MDWRSZ_SHIFT 18
+#define SPI_PFL_MODE_MDWRSZ_MASK (1 << SPI_PFL_MODE_MDWRSZ_SHIFT)
+#define SPI_PFL_MODE_3WIRE_SHIFT 20
+#define SPI_PFL_MODE_3WIRE_MASK (1 << SPI_PFL_MODE_3WIRE_SHIFT)
+
+/* SPI Ping-Pong FIFO registers */
+#define HSSPI_FIFO_SIZE 0x200
+#define HSSPI_FIFO_BASE (0x200 + \
+ (HSSPI_FIFO_SIZE * HSSPI_PP))
+
+/* SPI Ping-Pong FIFO OP register */
+#define HSSPI_FIFO_OP_SIZE 0x2
+#define HSSPI_FIFO_OP_REG (HSSPI_FIFO_BASE + 0x00)
+#define HSSPI_FIFO_OP_BYTES_SHIFT 0
+#define HSSPI_FIFO_OP_BYTES_MASK (0x3ff << HSSPI_FIFO_OP_BYTES_SHIFT)
+#define HSSPI_FIFO_OP_MBIT_SHIFT 11
+#define HSSPI_FIFO_OP_MBIT_MASK (1 << HSSPI_FIFO_OP_MBIT_SHIFT)
+#define HSSPI_FIFO_OP_CODE_SHIFT 13
+#define HSSPI_FIFO_OP_READ_WRITE (1 << HSSPI_FIFO_OP_CODE_SHIFT)
+#define HSSPI_FIFO_OP_CODE_W (2 << HSSPI_FIFO_OP_CODE_SHIFT)
+#define HSSPI_FIFO_OP_CODE_R (3 << HSSPI_FIFO_OP_CODE_SHIFT)
+
+struct bcm63xx_hsspi_priv {
+ void __iomem *regs;
+ ulong clk_rate;
+ uint8_t num_cs;
+ uint8_t cs_pols;
+ uint speed;
+};
+
+static int bcm63xx_hsspi_cs_info(struct udevice *bus, uint cs,
+ struct spi_cs_info *info)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(bus);
+
+ if (cs >= priv->num_cs) {
+ printf("no cs %u\n", cs);
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int bcm63xx_hsspi_set_mode(struct udevice *bus, uint mode)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(bus);
+
+ /* clock polarity */
+ if (mode & SPI_CPOL)
+ setbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CLK_POL_MASK);
+ else
+ clrbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CLK_POL_MASK);
+
+ return 0;
+}
+
+static int bcm63xx_hsspi_set_speed(struct udevice *bus, uint speed)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(bus);
+
+ priv->speed = speed;
+
+ return 0;
+}
+
+static void bcm63xx_hsspi_activate_cs(struct bcm63xx_hsspi_priv *priv,
+ struct dm_spi_slave_platdata *plat)
+{
+ uint32_t clr, set;
+
+ /* profile clock */
+ set = DIV_ROUND_UP(priv->clk_rate, priv->speed);
+ set = DIV_ROUND_UP(2048, set);
+ set &= SPI_PFL_CLK_FREQ_MASK;
+ set |= SPI_PFL_CLK_RSTLOOP_MASK;
+ writel_be(set, priv->regs + SPI_PFL_CLK_REG(plat->cs));
+
+ /* profile signal */
+ set = 0;
+ clr = SPI_PFL_SIG_LAUNCHRIS_MASK |
+ SPI_PFL_SIG_LATCHRIS_MASK |
+ SPI_PFL_SIG_ASYNCIN_MASK;
+
+ /* latch/launch config */
+ if (plat->mode & SPI_CPHA)
+ set |= SPI_PFL_SIG_LAUNCHRIS_MASK;
+ else
+ set |= SPI_PFL_SIG_LATCHRIS_MASK;
+
+ /* async clk */
+ if (priv->speed > SPI_MAX_SYNC_CLOCK)
+ set |= SPI_PFL_SIG_ASYNCIN_MASK;
+
+ clrsetbits_be32(priv->regs + SPI_PFL_SIG_REG(plat->cs), clr, set);
+
+ /* global control */
+ set = 0;
+ clr = 0;
+
+ /* invert cs polarity */
+ if (priv->cs_pols & BIT(plat->cs))
+ clr |= BIT(plat->cs);
+ else
+ set |= BIT(plat->cs);
+
+ /* invert dummy cs polarity */
+ if (priv->cs_pols & BIT(!plat->cs))
+ clr |= BIT(!plat->cs);
+ else
+ set |= BIT(!plat->cs);
+
+ clrsetbits_be32(priv->regs + SPI_CTL_REG, clr, set);
+}
+
+static void bcm63xx_hsspi_deactivate_cs(struct bcm63xx_hsspi_priv *priv)
+{
+ /* restore cs polarities */
+ clrsetbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CS_POL_MASK,
+ priv->cs_pols);
+}
+
+/*
+ * BCM63xx HSSPI driver doesn't allow keeping CS active between transfers
+ * because they are controlled by HW.
+ * However, it provides a mechanism to prepend write transfers prior to read
+ * transfers (with a maximum prepend of 15 bytes), which is usually enough for
+ * SPI-connected flashes since reading requires prepending a write transfer of
+ * 5 bytes. On the other hand it also provides a way to invert each CS
+ * polarity, not only between transfers like the older BCM63xx SPI driver, but
+ * also the rest of the time.
+ *
+ * Instead of using the prepend mechanism, this implementation inverts the
+ * polarity of both the desired CS and another dummy CS when the bus is
+ * claimed. This way, the dummy CS is restored to its inactive value when
+ * transfers are issued and the desired CS is preserved in its active value
+ * all the time. This hack is also used in the upstream linux driver and
+ * allows keeping CS active between trasnfers even if the HW doesn't give
+ * this possibility.
+ */
+static int bcm63xx_hsspi_xfer(struct udevice *dev, unsigned int bitlen,
+ const void *dout, void *din, unsigned long flags)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev->parent);
+ struct dm_spi_slave_platdata *plat = dev_get_parent_platdata(dev);
+ size_t data_bytes = bitlen / 8;
+ size_t step_size = HSSPI_FIFO_SIZE;
+ uint16_t opcode = 0;
+ uint32_t val;
+ const uint8_t *tx = dout;
+ uint8_t *rx = din;
+
+ if (flags & SPI_XFER_BEGIN)
+ bcm63xx_hsspi_activate_cs(priv, plat);
+
+ /* fifo operation */
+ if (tx && rx)
+ opcode = HSSPI_FIFO_OP_READ_WRITE;
+ else if (rx)
+ opcode = HSSPI_FIFO_OP_CODE_R;
+ else if (tx)
+ opcode = HSSPI_FIFO_OP_CODE_W;
+
+ if (opcode != HSSPI_FIFO_OP_CODE_R)
+ step_size -= HSSPI_FIFO_OP_SIZE;
+
+ /* dual mode */
+ if ((opcode == HSSPI_FIFO_OP_CODE_R && plat->mode == SPI_RX_DUAL) ||
+ (opcode == HSSPI_FIFO_OP_CODE_W && plat->mode == SPI_TX_DUAL))
+ opcode |= HSSPI_FIFO_OP_MBIT_MASK;
+
+ /* profile mode */
+ val = SPI_PFL_MODE_FILL_MASK |
+ SPI_PFL_MODE_MDRDSZ_MASK |
+ SPI_PFL_MODE_MDWRSZ_MASK;
+ if (plat->mode & SPI_3WIRE)
+ val |= SPI_PFL_MODE_3WIRE_MASK;
+ writel_be(val, priv->regs + SPI_PFL_MODE_REG(plat->cs));
+
+ /* transfer loop */
+ while (data_bytes > 0) {
+ size_t curr_step = min(step_size, data_bytes);
+ int ret;
+
+ /* copy tx data */
+ if (tx) {
+ memcpy_toio(priv->regs + HSSPI_FIFO_BASE +
+ HSSPI_FIFO_OP_SIZE, tx, curr_step);
+ tx += curr_step;
+ }
+
+ /* set fifo operation */
+ writew_be(opcode | (curr_step & HSSPI_FIFO_OP_BYTES_MASK),
+ priv->regs + HSSPI_FIFO_OP_REG);
+
+ /* issue the transfer */
+ val = SPI_CMD_OP_START;
+ val |= (plat->cs << SPI_CMD_PFL_SHIFT) &
+ SPI_CMD_PFL_MASK;
+ val |= (!plat->cs << SPI_CMD_SLAVE_SHIFT) &
+ SPI_CMD_SLAVE_MASK;
+ writel_be(val, priv->regs + SPI_CMD_REG);
+
+ /* wait for completion */
+ ret = wait_for_bit_be32(priv->regs + SPI_STAT_REG,
+ SPI_STAT_SRCBUSY_MASK, false,
+ 1000, false);
+ if (ret) {
+ printf("interrupt timeout\n");
+ return ret;
+ }
+
+ /* copy rx data */
+ if (rx) {
+ memcpy_fromio(rx, priv->regs + HSSPI_FIFO_BASE,
+ curr_step);
+ rx += curr_step;
+ }
+
+ data_bytes -= curr_step;
+ }
+
+ if (flags & SPI_XFER_END)
+ bcm63xx_hsspi_deactivate_cs(priv);
+
+ return 0;
+}
+
+static const struct dm_spi_ops bcm63xx_hsspi_ops = {
+ .cs_info = bcm63xx_hsspi_cs_info,
+ .set_mode = bcm63xx_hsspi_set_mode,
+ .set_speed = bcm63xx_hsspi_set_speed,
+ .xfer = bcm63xx_hsspi_xfer,
+};
+
+static const struct udevice_id bcm63xx_hsspi_ids[] = {
+ { .compatible = "brcm,bcm6328-hsspi", },
+ { /* sentinel */ }
+};
+
+static int bcm63xx_hsspi_child_pre_probe(struct udevice *dev)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev->parent);
+ struct dm_spi_slave_platdata *plat = dev_get_parent_platdata(dev);
+
+ /* check cs */
+ if (plat->cs >= priv->num_cs) {
+ printf("no cs %u\n", plat->cs);
+ return -ENODEV;
+ }
+
+ /* cs polarity */
+ if (plat->mode & SPI_CS_HIGH)
+ priv->cs_pols |= BIT(plat->cs);
+ else
+ priv->cs_pols &= ~BIT(plat->cs);
+
+ return 0;
+}
+
+static int bcm63xx_hsspi_probe(struct udevice *dev)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev);
+ struct reset_ctl rst_ctl;
+ struct clk clk;
+ fdt_addr_t addr;
+ fdt_size_t size;
+ int ret;
+
+ addr = devfdt_get_addr_size_index(dev, 0, &size);
+ if (addr == FDT_ADDR_T_NONE)
+ return -EINVAL;
+
+ priv->regs = ioremap(addr, size);
+ priv->num_cs = fdtdec_get_uint(gd->fdt_blob, dev_of_offset(dev),
+ "num-cs", 8);
+
+ /* enable clock */
+ ret = clk_get_by_name(dev, "hsspi", &clk);
+ if (ret < 0)
+ return ret;
+
+ ret = clk_enable(&clk);
+ if (ret < 0)
+ return ret;
+
+ ret = clk_free(&clk);
+ if (ret < 0)
+ return ret;
+
+ /* get clock rate */
+ ret = clk_get_by_name(dev, "pll", &clk);
+ if (ret < 0)
+ return ret;
+
+ priv->clk_rate = clk_get_rate(&clk);
+
+ ret = clk_free(&clk);
+ if (ret < 0)
+ return ret;
+
+ /* perform reset */
+ ret = reset_get_by_index(dev, 0, &rst_ctl);
+ if (ret < 0)
+ return ret;
+
+ ret = reset_deassert(&rst_ctl);
+ if (ret < 0)
+ return ret;
+
+ ret = reset_free(&rst_ctl);
+ if (ret < 0)
+ return ret;
+
+ /* initialize hardware */
+ writel_be(0, priv->regs + SPI_IR_MASK_REG);
+
+ /* clear pending interrupts */
+ writel_be(SPI_IR_CLEAR_ALL, priv->regs + SPI_IR_STAT_REG);
+
+ /* enable clk gate */
+ setbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CLK_GATE_MASK);
+
+ /* read default cs polarities */
+ priv->cs_pols = readl_be(priv->regs + SPI_CTL_REG) &
+ SPI_CTL_CS_POL_MASK;
+
+ return 0;
+}
+
+U_BOOT_DRIVER(bcm63xx_hsspi) = {
+ .name = "bcm63xx_hsspi",
+ .id = UCLASS_SPI,
+ .of_match = bcm63xx_hsspi_ids,
+ .ops = &bcm63xx_hsspi_ops,
+ .priv_auto_alloc_size = sizeof(struct bcm63xx_hsspi_priv),
+ .child_pre_probe = bcm63xx_hsspi_child_pre_probe,
+ .probe = bcm63xx_hsspi_probe,
+};
--
2.11.0
^ permalink raw reply related [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v5 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328
2018-01-15 18:45 ` [U-Boot] [PATCH v5 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
2018-01-15 18:45 ` [U-Boot] [PATCH v5 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
@ 2018-01-15 18:45 ` Álvaro Fernández Rojas
2018-01-15 18:45 ` [U-Boot] [PATCH v5 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268 Álvaro Fernández Rojas
2018-01-15 18:45 ` [U-Boot] [PATCH v5 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un Álvaro Fernández Rojas
3 siblings, 0 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2018-01-15 18:45 UTC (permalink / raw)
To: u-boot
This driver manages the SPI controller present on this SoC.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
---
v5: no changes
v4: no changes
v3: no changes
v2: no changes
arch/mips/dts/brcm,bcm6328.dtsi | 24 ++++++++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/arch/mips/dts/brcm,bcm6328.dtsi b/arch/mips/dts/brcm,bcm6328.dtsi
index a996075743..67d9278be4 100644
--- a/arch/mips/dts/brcm,bcm6328.dtsi
+++ b/arch/mips/dts/brcm,bcm6328.dtsi
@@ -13,6 +13,10 @@
/ {
compatible = "brcm,bcm6328";
+ aliases {
+ spi0 = &spi;
+ };
+
cpus {
reg = <0x10000000 0x4>;
#address-cells = <1>;
@@ -40,6 +44,12 @@
#size-cells = <1>;
u-boot,dm-pre-reloc;
+ hsspi_pll: hsspi-pll {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <133333333>;
+ };
+
periph_osc: periph-osc {
compatible = "fixed-clock";
#clock-cells = <0>;
@@ -123,6 +133,20 @@
status = "disabled";
};
+ spi: spi at 10001000 {
+ compatible = "brcm,bcm6328-hsspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x10001000 0x600>;
+ clocks = <&periph_clk BCM6328_CLK_HSSPI>, <&hsspi_pll>;
+ clock-names = "hsspi", "pll";
+ resets = <&periph_rst BCM6328_RST_SPI>;
+ spi-max-frequency = <33333334>;
+ num-cs = <3>;
+
+ status = "disabled";
+ };
+
periph_pwr: power-controller at 10001848 {
compatible = "brcm,bcm6328-power-domain";
reg = <0x10001848 0x4>;
--
2.11.0
^ permalink raw reply related [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v5 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268
2018-01-15 18:45 ` [U-Boot] [PATCH v5 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
2018-01-15 18:45 ` [U-Boot] [PATCH v5 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
2018-01-15 18:45 ` [U-Boot] [PATCH v5 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328 Álvaro Fernández Rojas
@ 2018-01-15 18:45 ` Álvaro Fernández Rojas
2018-01-15 18:45 ` [U-Boot] [PATCH v5 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un Álvaro Fernández Rojas
3 siblings, 0 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2018-01-15 18:45 UTC (permalink / raw)
To: u-boot
This driver manages the high speed SPI controller present on this SoC.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
---
v5: no changes
v4: no changes
v3: no changes
v2: no changes
arch/mips/dts/brcm,bcm63268.dtsi | 21 +++++++++++++++++++++
1 file changed, 21 insertions(+)
diff --git a/arch/mips/dts/brcm,bcm63268.dtsi b/arch/mips/dts/brcm,bcm63268.dtsi
index 6e3d9c3820..4d4e36cccc 100644
--- a/arch/mips/dts/brcm,bcm63268.dtsi
+++ b/arch/mips/dts/brcm,bcm63268.dtsi
@@ -15,6 +15,7 @@
aliases {
spi0 = &lsspi;
+ spi1 = &hsspi;
};
cpus {
@@ -44,6 +45,12 @@
#size-cells = <1>;
u-boot,dm-pre-reloc;
+ hsspi_pll: hsspi-pll {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <400000000>;
+ };
+
periph_osc: periph-osc {
compatible = "fixed-clock";
#clock-cells = <0>;
@@ -153,6 +160,20 @@
status = "disabled";
};
+ hsspi: spi at 10001000 {
+ compatible = "brcm,bcm6328-hsspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x10001000 0x600>;
+ clocks = <&periph_clk BCM63268_CLK_HSSPI>, <&hsspi_pll>;
+ clock-names = "hsspi", "pll";
+ resets = <&periph_rst BCM63268_RST_SPI>;
+ spi-max-frequency = <50000000>;
+ num-cs = <8>;
+
+ status = "disabled";
+ };
+
leds: led-controller at 10001900 {
compatible = "brcm,bcm6328-leds";
reg = <0x10001900 0x24>;
--
2.11.0
^ permalink raw reply related [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v5 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un
2018-01-15 18:45 ` [U-Boot] [PATCH v5 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
` (2 preceding siblings ...)
2018-01-15 18:45 ` [U-Boot] [PATCH v5 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268 Álvaro Fernández Rojas
@ 2018-01-15 18:45 ` Álvaro Fernández Rojas
3 siblings, 0 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2018-01-15 18:45 UTC (permalink / raw)
To: u-boot
It's a Macronix (mx25l12805d) 16 MB SPI flash.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
---
v5: no changes
v4: Sync with master.
v3: switch to CONFIG_BCM63XX_HSSPI
v2: no changes
arch/mips/dts/comtrend,ar-5387un.dts | 12 ++++++++++++
configs/comtrend_ar5387un_ram_defconfig | 8 ++++++++
2 files changed, 20 insertions(+)
diff --git a/arch/mips/dts/comtrend,ar-5387un.dts b/arch/mips/dts/comtrend,ar-5387un.dts
index 73f2b49b76..6067881a78 100644
--- a/arch/mips/dts/comtrend,ar-5387un.dts
+++ b/arch/mips/dts/comtrend,ar-5387un.dts
@@ -51,6 +51,18 @@
};
};
+&spi {
+ status = "okay";
+
+ spi-flash at 0 {
+ compatible = "spi-flash";
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <33333334>;
+ };
+};
+
&uart0 {
u-boot,dm-pre-reloc;
status = "okay";
diff --git a/configs/comtrend_ar5387un_ram_defconfig b/configs/comtrend_ar5387un_ram_defconfig
index b64018ae71..59ec86b253 100644
--- a/configs/comtrend_ar5387un_ram_defconfig
+++ b/configs/comtrend_ar5387un_ram_defconfig
@@ -41,3 +41,11 @@ CONFIG_RESET_BCM6345=y
# CONFIG_SPL_SERIAL_PRESENT is not set
CONFIG_DM_SERIAL=y
CONFIG_BCM6345_SERIAL=y
+CONFIG_BCM63XX_HSSPI=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_MTD=y
+CONFIG_SPI_FLASH_MACRONIX=y
--
2.11.0
^ permalink raw reply related [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v6 0/4] mips: bmips: add HSSPI support
2017-05-23 19:18 [U-Boot] [PATCH 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
` (7 preceding siblings ...)
2018-01-15 18:45 ` [U-Boot] [PATCH v5 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
@ 2018-01-20 1:13 ` Álvaro Fernández Rojas
2018-01-20 1:13 ` [U-Boot] [PATCH v6 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
` (4 more replies)
8 siblings, 5 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2018-01-20 1:13 UTC (permalink / raw)
To: u-boot
BCM63xx HSSPI controller has the same issue as BCM63xx SPI controller: it
doesn't allow keeping CS active between transfers.
However, this controller allows changing CS polarities, which is used in the
linux upstream driver to manage CS as desired.
v6: Introduce changes suggested by Simon Glass:
- Fix defconfig order.
v5: Introduce changes suggested by Jagan Teki:
- Rename SPI_PP_ macros.
- cs_activate instead of claim_cs.
- deactivate_cs instead of release_cs.
- Use wait_for_bit_be32 instead of infinite loop.
v4: Sync with master.
v3: Switch to CONFIG_BCM63XX_HSSPI and rebase on top of SPI v4.
v2: Introduce changes suggested by Simon Glass:
- Split bcm63xx_hsspi_xfer() into smaller functions.
- Check possible clock errors.
- Check possible reset errors.
- Switch to devfdt_get_addr_size_index().
- Use setbits32_be() for clock gate.
Álvaro Fernández Rojas (4):
dm: spi: add BCM63xx HSSPI driver
mips: bmips: add bcm63xx-hsspi driver support for BCM6328
mips: bmips: add bcm63xx-hsspi driver support for BCM63268
mips: bmips: enable the SPI flash on the Comtrend AR-5387un
arch/mips/dts/brcm,bcm63268.dtsi | 21 ++
arch/mips/dts/brcm,bcm6328.dtsi | 24 ++
arch/mips/dts/comtrend,ar-5387un.dts | 12 +
configs/comtrend_ar5387un_ram_defconfig | 8 +
drivers/spi/Kconfig | 8 +
drivers/spi/Makefile | 1 +
drivers/spi/bcm63xx_hsspi.c | 414 ++++++++++++++++++++++++++++++++
7 files changed, 488 insertions(+)
create mode 100644 drivers/spi/bcm63xx_hsspi.c
--
2.11.0
^ permalink raw reply [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v6 1/4] dm: spi: add BCM63xx HSSPI driver
2018-01-20 1:13 ` [U-Boot] [PATCH v6 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
@ 2018-01-20 1:13 ` Álvaro Fernández Rojas
2018-01-20 1:13 ` [U-Boot] [PATCH v6 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328 Álvaro Fernández Rojas
` (3 subsequent siblings)
4 siblings, 0 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2018-01-20 1:13 UTC (permalink / raw)
To: u-boot
This driver is a simplified version of linux/drivers/spi/spi-bcm63xx-hsspi.c
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
---
v6: no changes
v5: Introduce changes suggested by Jagan Teki:
- Rename SPI_PP_ macros.
- cs_activate instead of claim_cs.
- deactivate_cs instead of release_cs.
- Use wait_for_bit_be32 instead of infinite loop.
v4: no changes.
v3: Switch to CONFIG_BCM63XX_HSSPI and rebase on top of SPI v4.
v2: Introduce changes suggested by Simon Glass:
- Split bcm63xx_hsspi_xfer() into smaller functions.
- Check possible clock errors.
- Check possible reset errors.
- Switch to devfdt_get_addr_size_index().
- Use setbits32_be() for clock gate.
drivers/spi/Kconfig | 8 +
drivers/spi/Makefile | 1 +
drivers/spi/bcm63xx_hsspi.c | 414 ++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 423 insertions(+)
create mode 100644 drivers/spi/bcm63xx_hsspi.c
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index ebc71c2e42..28ddcf85a3 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -40,6 +40,14 @@ config ATMEL_SPI
many AT91 (ARM) chips. This driver can be used to access
the SPI Flash, such as AT25DF321.
+config BCM63XX_HSSPI
+ bool "BCM63XX HSSPI driver"
+ depends on ARCH_BMIPS
+ help
+ Enable the BCM6328 HSSPI driver. This driver can be used to
+ access the SPI NOR flash on platforms embedding this Broadcom
+ SPI core.
+
config BCM63XX_SPI
bool "BCM6348 SPI driver"
depends on ARCH_BMIPS
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 5770b3f7cc..4b6000fd9a 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -18,6 +18,7 @@ endif
obj-$(CONFIG_ALTERA_SPI) += altera_spi.o
obj-$(CONFIG_ATH79_SPI) += ath79_spi.o
obj-$(CONFIG_ATMEL_SPI) += atmel_spi.o
+obj-$(CONFIG_BCM63XX_HSSPI) += bcm63xx_hsspi.o
obj-$(CONFIG_BCM63XX_SPI) += bcm63xx_spi.o
obj-$(CONFIG_CADENCE_QSPI) += cadence_qspi.o cadence_qspi_apb.o
obj-$(CONFIG_CF_SPI) += cf_spi.o
diff --git a/drivers/spi/bcm63xx_hsspi.c b/drivers/spi/bcm63xx_hsspi.c
new file mode 100644
index 0000000000..3393166a1e
--- /dev/null
+++ b/drivers/spi/bcm63xx_hsspi.c
@@ -0,0 +1,414 @@
+/*
+ * Copyright (C) 2017 Álvaro Fernández Rojas <noltari@gmail.com>
+ *
+ * Derived from linux/drivers/spi/spi-bcm63xx-hsspi.c:
+ * Copyright (C) 2000-2010 Broadcom Corporation
+ * Copyright (C) 2012-2013 Jonas Gorski <jogo@openwrt.org>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <clk.h>
+#include <dm.h>
+#include <spi.h>
+#include <reset.h>
+#include <wait_bit.h>
+#include <asm/io.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define HSSPI_PP 0
+
+#define SPI_MAX_SYNC_CLOCK 30000000
+
+/* SPI Control register */
+#define SPI_CTL_REG 0x000
+#define SPI_CTL_CS_POL_SHIFT 0
+#define SPI_CTL_CS_POL_MASK (0xff << SPI_CTL_CS_POL_SHIFT)
+#define SPI_CTL_CLK_GATE_SHIFT 16
+#define SPI_CTL_CLK_GATE_MASK (1 << SPI_CTL_CLK_GATE_SHIFT)
+#define SPI_CTL_CLK_POL_SHIFT 17
+#define SPI_CTL_CLK_POL_MASK (1 << SPI_CTL_CLK_POL_SHIFT)
+
+/* SPI Interrupts registers */
+#define SPI_IR_STAT_REG 0x008
+#define SPI_IR_ST_MASK_REG 0x00c
+#define SPI_IR_MASK_REG 0x010
+
+#define SPI_IR_CLEAR_ALL 0xff001f1f
+
+/* SPI Ping-Pong Command registers */
+#define SPI_CMD_REG (0x080 + (0x40 * (HSSPI_PP)) + 0x00)
+#define SPI_CMD_OP_SHIFT 0
+#define SPI_CMD_OP_START (0x1 << SPI_CMD_OP_SHIFT)
+#define SPI_CMD_PFL_SHIFT 8
+#define SPI_CMD_PFL_MASK (0x7 << SPI_CMD_PFL_SHIFT)
+#define SPI_CMD_SLAVE_SHIFT 12
+#define SPI_CMD_SLAVE_MASK (0x7 << SPI_CMD_SLAVE_SHIFT)
+
+/* SPI Ping-Pong Status registers */
+#define SPI_STAT_REG (0x080 + (0x40 * (HSSPI_PP)) + 0x04)
+#define SPI_STAT_SRCBUSY_SHIFT 1
+#define SPI_STAT_SRCBUSY_MASK (1 << SPI_STAT_SRCBUSY_SHIFT)
+
+/* SPI Profile Clock registers */
+#define SPI_PFL_CLK_REG(x) (0x100 + (0x20 * (x)) + 0x00)
+#define SPI_PFL_CLK_FREQ_SHIFT 0
+#define SPI_PFL_CLK_FREQ_MASK (0x3fff << SPI_PFL_CLK_FREQ_SHIFT)
+#define SPI_PFL_CLK_RSTLOOP_SHIFT 15
+#define SPI_PFL_CLK_RSTLOOP_MASK (1 << SPI_PFL_CLK_RSTLOOP_SHIFT)
+
+/* SPI Profile Signal registers */
+#define SPI_PFL_SIG_REG(x) (0x100 + (0x20 * (x)) + 0x04)
+#define SPI_PFL_SIG_LATCHRIS_SHIFT 12
+#define SPI_PFL_SIG_LATCHRIS_MASK (1 << SPI_PFL_SIG_LATCHRIS_SHIFT)
+#define SPI_PFL_SIG_LAUNCHRIS_SHIFT 13
+#define SPI_PFL_SIG_LAUNCHRIS_MASK (1 << SPI_PFL_SIG_LAUNCHRIS_SHIFT)
+#define SPI_PFL_SIG_ASYNCIN_SHIFT 16
+#define SPI_PFL_SIG_ASYNCIN_MASK (1 << SPI_PFL_SIG_ASYNCIN_SHIFT)
+
+/* SPI Profile Mode registers */
+#define SPI_PFL_MODE_REG(x) (0x100 + (0x20 * (x)) + 0x08)
+#define SPI_PFL_MODE_FILL_SHIFT 0
+#define SPI_PFL_MODE_FILL_MASK (0xff << SPI_PFL_MODE_FILL_SHIFT)
+#define SPI_PFL_MODE_MDRDSZ_SHIFT 16
+#define SPI_PFL_MODE_MDRDSZ_MASK (1 << SPI_PFL_MODE_MDRDSZ_SHIFT)
+#define SPI_PFL_MODE_MDWRSZ_SHIFT 18
+#define SPI_PFL_MODE_MDWRSZ_MASK (1 << SPI_PFL_MODE_MDWRSZ_SHIFT)
+#define SPI_PFL_MODE_3WIRE_SHIFT 20
+#define SPI_PFL_MODE_3WIRE_MASK (1 << SPI_PFL_MODE_3WIRE_SHIFT)
+
+/* SPI Ping-Pong FIFO registers */
+#define HSSPI_FIFO_SIZE 0x200
+#define HSSPI_FIFO_BASE (0x200 + \
+ (HSSPI_FIFO_SIZE * HSSPI_PP))
+
+/* SPI Ping-Pong FIFO OP register */
+#define HSSPI_FIFO_OP_SIZE 0x2
+#define HSSPI_FIFO_OP_REG (HSSPI_FIFO_BASE + 0x00)
+#define HSSPI_FIFO_OP_BYTES_SHIFT 0
+#define HSSPI_FIFO_OP_BYTES_MASK (0x3ff << HSSPI_FIFO_OP_BYTES_SHIFT)
+#define HSSPI_FIFO_OP_MBIT_SHIFT 11
+#define HSSPI_FIFO_OP_MBIT_MASK (1 << HSSPI_FIFO_OP_MBIT_SHIFT)
+#define HSSPI_FIFO_OP_CODE_SHIFT 13
+#define HSSPI_FIFO_OP_READ_WRITE (1 << HSSPI_FIFO_OP_CODE_SHIFT)
+#define HSSPI_FIFO_OP_CODE_W (2 << HSSPI_FIFO_OP_CODE_SHIFT)
+#define HSSPI_FIFO_OP_CODE_R (3 << HSSPI_FIFO_OP_CODE_SHIFT)
+
+struct bcm63xx_hsspi_priv {
+ void __iomem *regs;
+ ulong clk_rate;
+ uint8_t num_cs;
+ uint8_t cs_pols;
+ uint speed;
+};
+
+static int bcm63xx_hsspi_cs_info(struct udevice *bus, uint cs,
+ struct spi_cs_info *info)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(bus);
+
+ if (cs >= priv->num_cs) {
+ printf("no cs %u\n", cs);
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int bcm63xx_hsspi_set_mode(struct udevice *bus, uint mode)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(bus);
+
+ /* clock polarity */
+ if (mode & SPI_CPOL)
+ setbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CLK_POL_MASK);
+ else
+ clrbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CLK_POL_MASK);
+
+ return 0;
+}
+
+static int bcm63xx_hsspi_set_speed(struct udevice *bus, uint speed)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(bus);
+
+ priv->speed = speed;
+
+ return 0;
+}
+
+static void bcm63xx_hsspi_activate_cs(struct bcm63xx_hsspi_priv *priv,
+ struct dm_spi_slave_platdata *plat)
+{
+ uint32_t clr, set;
+
+ /* profile clock */
+ set = DIV_ROUND_UP(priv->clk_rate, priv->speed);
+ set = DIV_ROUND_UP(2048, set);
+ set &= SPI_PFL_CLK_FREQ_MASK;
+ set |= SPI_PFL_CLK_RSTLOOP_MASK;
+ writel_be(set, priv->regs + SPI_PFL_CLK_REG(plat->cs));
+
+ /* profile signal */
+ set = 0;
+ clr = SPI_PFL_SIG_LAUNCHRIS_MASK |
+ SPI_PFL_SIG_LATCHRIS_MASK |
+ SPI_PFL_SIG_ASYNCIN_MASK;
+
+ /* latch/launch config */
+ if (plat->mode & SPI_CPHA)
+ set |= SPI_PFL_SIG_LAUNCHRIS_MASK;
+ else
+ set |= SPI_PFL_SIG_LATCHRIS_MASK;
+
+ /* async clk */
+ if (priv->speed > SPI_MAX_SYNC_CLOCK)
+ set |= SPI_PFL_SIG_ASYNCIN_MASK;
+
+ clrsetbits_be32(priv->regs + SPI_PFL_SIG_REG(plat->cs), clr, set);
+
+ /* global control */
+ set = 0;
+ clr = 0;
+
+ /* invert cs polarity */
+ if (priv->cs_pols & BIT(plat->cs))
+ clr |= BIT(plat->cs);
+ else
+ set |= BIT(plat->cs);
+
+ /* invert dummy cs polarity */
+ if (priv->cs_pols & BIT(!plat->cs))
+ clr |= BIT(!plat->cs);
+ else
+ set |= BIT(!plat->cs);
+
+ clrsetbits_be32(priv->regs + SPI_CTL_REG, clr, set);
+}
+
+static void bcm63xx_hsspi_deactivate_cs(struct bcm63xx_hsspi_priv *priv)
+{
+ /* restore cs polarities */
+ clrsetbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CS_POL_MASK,
+ priv->cs_pols);
+}
+
+/*
+ * BCM63xx HSSPI driver doesn't allow keeping CS active between transfers
+ * because they are controlled by HW.
+ * However, it provides a mechanism to prepend write transfers prior to read
+ * transfers (with a maximum prepend of 15 bytes), which is usually enough for
+ * SPI-connected flashes since reading requires prepending a write transfer of
+ * 5 bytes. On the other hand it also provides a way to invert each CS
+ * polarity, not only between transfers like the older BCM63xx SPI driver, but
+ * also the rest of the time.
+ *
+ * Instead of using the prepend mechanism, this implementation inverts the
+ * polarity of both the desired CS and another dummy CS when the bus is
+ * claimed. This way, the dummy CS is restored to its inactive value when
+ * transfers are issued and the desired CS is preserved in its active value
+ * all the time. This hack is also used in the upstream linux driver and
+ * allows keeping CS active between trasnfers even if the HW doesn't give
+ * this possibility.
+ */
+static int bcm63xx_hsspi_xfer(struct udevice *dev, unsigned int bitlen,
+ const void *dout, void *din, unsigned long flags)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev->parent);
+ struct dm_spi_slave_platdata *plat = dev_get_parent_platdata(dev);
+ size_t data_bytes = bitlen / 8;
+ size_t step_size = HSSPI_FIFO_SIZE;
+ uint16_t opcode = 0;
+ uint32_t val;
+ const uint8_t *tx = dout;
+ uint8_t *rx = din;
+
+ if (flags & SPI_XFER_BEGIN)
+ bcm63xx_hsspi_activate_cs(priv, plat);
+
+ /* fifo operation */
+ if (tx && rx)
+ opcode = HSSPI_FIFO_OP_READ_WRITE;
+ else if (rx)
+ opcode = HSSPI_FIFO_OP_CODE_R;
+ else if (tx)
+ opcode = HSSPI_FIFO_OP_CODE_W;
+
+ if (opcode != HSSPI_FIFO_OP_CODE_R)
+ step_size -= HSSPI_FIFO_OP_SIZE;
+
+ /* dual mode */
+ if ((opcode == HSSPI_FIFO_OP_CODE_R && plat->mode == SPI_RX_DUAL) ||
+ (opcode == HSSPI_FIFO_OP_CODE_W && plat->mode == SPI_TX_DUAL))
+ opcode |= HSSPI_FIFO_OP_MBIT_MASK;
+
+ /* profile mode */
+ val = SPI_PFL_MODE_FILL_MASK |
+ SPI_PFL_MODE_MDRDSZ_MASK |
+ SPI_PFL_MODE_MDWRSZ_MASK;
+ if (plat->mode & SPI_3WIRE)
+ val |= SPI_PFL_MODE_3WIRE_MASK;
+ writel_be(val, priv->regs + SPI_PFL_MODE_REG(plat->cs));
+
+ /* transfer loop */
+ while (data_bytes > 0) {
+ size_t curr_step = min(step_size, data_bytes);
+ int ret;
+
+ /* copy tx data */
+ if (tx) {
+ memcpy_toio(priv->regs + HSSPI_FIFO_BASE +
+ HSSPI_FIFO_OP_SIZE, tx, curr_step);
+ tx += curr_step;
+ }
+
+ /* set fifo operation */
+ writew_be(opcode | (curr_step & HSSPI_FIFO_OP_BYTES_MASK),
+ priv->regs + HSSPI_FIFO_OP_REG);
+
+ /* issue the transfer */
+ val = SPI_CMD_OP_START;
+ val |= (plat->cs << SPI_CMD_PFL_SHIFT) &
+ SPI_CMD_PFL_MASK;
+ val |= (!plat->cs << SPI_CMD_SLAVE_SHIFT) &
+ SPI_CMD_SLAVE_MASK;
+ writel_be(val, priv->regs + SPI_CMD_REG);
+
+ /* wait for completion */
+ ret = wait_for_bit_be32(priv->regs + SPI_STAT_REG,
+ SPI_STAT_SRCBUSY_MASK, false,
+ 1000, false);
+ if (ret) {
+ printf("interrupt timeout\n");
+ return ret;
+ }
+
+ /* copy rx data */
+ if (rx) {
+ memcpy_fromio(rx, priv->regs + HSSPI_FIFO_BASE,
+ curr_step);
+ rx += curr_step;
+ }
+
+ data_bytes -= curr_step;
+ }
+
+ if (flags & SPI_XFER_END)
+ bcm63xx_hsspi_deactivate_cs(priv);
+
+ return 0;
+}
+
+static const struct dm_spi_ops bcm63xx_hsspi_ops = {
+ .cs_info = bcm63xx_hsspi_cs_info,
+ .set_mode = bcm63xx_hsspi_set_mode,
+ .set_speed = bcm63xx_hsspi_set_speed,
+ .xfer = bcm63xx_hsspi_xfer,
+};
+
+static const struct udevice_id bcm63xx_hsspi_ids[] = {
+ { .compatible = "brcm,bcm6328-hsspi", },
+ { /* sentinel */ }
+};
+
+static int bcm63xx_hsspi_child_pre_probe(struct udevice *dev)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev->parent);
+ struct dm_spi_slave_platdata *plat = dev_get_parent_platdata(dev);
+
+ /* check cs */
+ if (plat->cs >= priv->num_cs) {
+ printf("no cs %u\n", plat->cs);
+ return -ENODEV;
+ }
+
+ /* cs polarity */
+ if (plat->mode & SPI_CS_HIGH)
+ priv->cs_pols |= BIT(plat->cs);
+ else
+ priv->cs_pols &= ~BIT(plat->cs);
+
+ return 0;
+}
+
+static int bcm63xx_hsspi_probe(struct udevice *dev)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev);
+ struct reset_ctl rst_ctl;
+ struct clk clk;
+ fdt_addr_t addr;
+ fdt_size_t size;
+ int ret;
+
+ addr = devfdt_get_addr_size_index(dev, 0, &size);
+ if (addr == FDT_ADDR_T_NONE)
+ return -EINVAL;
+
+ priv->regs = ioremap(addr, size);
+ priv->num_cs = fdtdec_get_uint(gd->fdt_blob, dev_of_offset(dev),
+ "num-cs", 8);
+
+ /* enable clock */
+ ret = clk_get_by_name(dev, "hsspi", &clk);
+ if (ret < 0)
+ return ret;
+
+ ret = clk_enable(&clk);
+ if (ret < 0)
+ return ret;
+
+ ret = clk_free(&clk);
+ if (ret < 0)
+ return ret;
+
+ /* get clock rate */
+ ret = clk_get_by_name(dev, "pll", &clk);
+ if (ret < 0)
+ return ret;
+
+ priv->clk_rate = clk_get_rate(&clk);
+
+ ret = clk_free(&clk);
+ if (ret < 0)
+ return ret;
+
+ /* perform reset */
+ ret = reset_get_by_index(dev, 0, &rst_ctl);
+ if (ret < 0)
+ return ret;
+
+ ret = reset_deassert(&rst_ctl);
+ if (ret < 0)
+ return ret;
+
+ ret = reset_free(&rst_ctl);
+ if (ret < 0)
+ return ret;
+
+ /* initialize hardware */
+ writel_be(0, priv->regs + SPI_IR_MASK_REG);
+
+ /* clear pending interrupts */
+ writel_be(SPI_IR_CLEAR_ALL, priv->regs + SPI_IR_STAT_REG);
+
+ /* enable clk gate */
+ setbits_be32(priv->regs + SPI_CTL_REG, SPI_CTL_CLK_GATE_MASK);
+
+ /* read default cs polarities */
+ priv->cs_pols = readl_be(priv->regs + SPI_CTL_REG) &
+ SPI_CTL_CS_POL_MASK;
+
+ return 0;
+}
+
+U_BOOT_DRIVER(bcm63xx_hsspi) = {
+ .name = "bcm63xx_hsspi",
+ .id = UCLASS_SPI,
+ .of_match = bcm63xx_hsspi_ids,
+ .ops = &bcm63xx_hsspi_ops,
+ .priv_auto_alloc_size = sizeof(struct bcm63xx_hsspi_priv),
+ .child_pre_probe = bcm63xx_hsspi_child_pre_probe,
+ .probe = bcm63xx_hsspi_probe,
+};
--
2.11.0
^ permalink raw reply related [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v6 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328
2018-01-20 1:13 ` [U-Boot] [PATCH v6 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
2018-01-20 1:13 ` [U-Boot] [PATCH v6 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
@ 2018-01-20 1:13 ` Álvaro Fernández Rojas
2018-01-20 1:13 ` [U-Boot] [PATCH v6 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268 Álvaro Fernández Rojas
` (2 subsequent siblings)
4 siblings, 0 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2018-01-20 1:13 UTC (permalink / raw)
To: u-boot
This driver manages the SPI controller present on this SoC.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
---
v6: no changes
v5: no changes
v4: no changes
v3: no changes
v2: no changes
arch/mips/dts/brcm,bcm6328.dtsi | 24 ++++++++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/arch/mips/dts/brcm,bcm6328.dtsi b/arch/mips/dts/brcm,bcm6328.dtsi
index a996075743..67d9278be4 100644
--- a/arch/mips/dts/brcm,bcm6328.dtsi
+++ b/arch/mips/dts/brcm,bcm6328.dtsi
@@ -13,6 +13,10 @@
/ {
compatible = "brcm,bcm6328";
+ aliases {
+ spi0 = &spi;
+ };
+
cpus {
reg = <0x10000000 0x4>;
#address-cells = <1>;
@@ -40,6 +44,12 @@
#size-cells = <1>;
u-boot,dm-pre-reloc;
+ hsspi_pll: hsspi-pll {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <133333333>;
+ };
+
periph_osc: periph-osc {
compatible = "fixed-clock";
#clock-cells = <0>;
@@ -123,6 +133,20 @@
status = "disabled";
};
+ spi: spi at 10001000 {
+ compatible = "brcm,bcm6328-hsspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x10001000 0x600>;
+ clocks = <&periph_clk BCM6328_CLK_HSSPI>, <&hsspi_pll>;
+ clock-names = "hsspi", "pll";
+ resets = <&periph_rst BCM6328_RST_SPI>;
+ spi-max-frequency = <33333334>;
+ num-cs = <3>;
+
+ status = "disabled";
+ };
+
periph_pwr: power-controller at 10001848 {
compatible = "brcm,bcm6328-power-domain";
reg = <0x10001848 0x4>;
--
2.11.0
^ permalink raw reply related [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v6 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268
2018-01-20 1:13 ` [U-Boot] [PATCH v6 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
2018-01-20 1:13 ` [U-Boot] [PATCH v6 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
2018-01-20 1:13 ` [U-Boot] [PATCH v6 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328 Álvaro Fernández Rojas
@ 2018-01-20 1:13 ` Álvaro Fernández Rojas
2018-01-20 1:13 ` [U-Boot] [PATCH v6 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un Álvaro Fernández Rojas
2018-01-22 5:11 ` [U-Boot] [PATCH v6 0/4] mips: bmips: add HSSPI support Jagan Teki
4 siblings, 0 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2018-01-20 1:13 UTC (permalink / raw)
To: u-boot
This driver manages the high speed SPI controller present on this SoC.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
---
v6: no changes
v5: no changes
v4: no changes
v3: no changes
v2: no changes
arch/mips/dts/brcm,bcm63268.dtsi | 21 +++++++++++++++++++++
1 file changed, 21 insertions(+)
diff --git a/arch/mips/dts/brcm,bcm63268.dtsi b/arch/mips/dts/brcm,bcm63268.dtsi
index 6e3d9c3820..4d4e36cccc 100644
--- a/arch/mips/dts/brcm,bcm63268.dtsi
+++ b/arch/mips/dts/brcm,bcm63268.dtsi
@@ -15,6 +15,7 @@
aliases {
spi0 = &lsspi;
+ spi1 = &hsspi;
};
cpus {
@@ -44,6 +45,12 @@
#size-cells = <1>;
u-boot,dm-pre-reloc;
+ hsspi_pll: hsspi-pll {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <400000000>;
+ };
+
periph_osc: periph-osc {
compatible = "fixed-clock";
#clock-cells = <0>;
@@ -153,6 +160,20 @@
status = "disabled";
};
+ hsspi: spi at 10001000 {
+ compatible = "brcm,bcm6328-hsspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x10001000 0x600>;
+ clocks = <&periph_clk BCM63268_CLK_HSSPI>, <&hsspi_pll>;
+ clock-names = "hsspi", "pll";
+ resets = <&periph_rst BCM63268_RST_SPI>;
+ spi-max-frequency = <50000000>;
+ num-cs = <8>;
+
+ status = "disabled";
+ };
+
leds: led-controller at 10001900 {
compatible = "brcm,bcm6328-leds";
reg = <0x10001900 0x24>;
--
2.11.0
^ permalink raw reply related [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v6 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un
2018-01-20 1:13 ` [U-Boot] [PATCH v6 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
` (2 preceding siblings ...)
2018-01-20 1:13 ` [U-Boot] [PATCH v6 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268 Álvaro Fernández Rojas
@ 2018-01-20 1:13 ` Álvaro Fernández Rojas
2018-01-22 5:11 ` [U-Boot] [PATCH v6 0/4] mips: bmips: add HSSPI support Jagan Teki
4 siblings, 0 replies; 45+ messages in thread
From: Álvaro Fernández Rojas @ 2018-01-20 1:13 UTC (permalink / raw)
To: u-boot
It's a Macronix (mx25l12805d) 16 MB SPI flash.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
---
v6: Introduce changes suggested by Simon Glass:
- Fix defconfig order.
v5: no changes
v4: Sync with master.
v3: switch to CONFIG_BCM63XX_HSSPI
v2: no changes
arch/mips/dts/comtrend,ar-5387un.dts | 12 ++++++++++++
configs/comtrend_ar5387un_ram_defconfig | 8 ++++++++
2 files changed, 20 insertions(+)
diff --git a/arch/mips/dts/comtrend,ar-5387un.dts b/arch/mips/dts/comtrend,ar-5387un.dts
index 73f2b49b76..6067881a78 100644
--- a/arch/mips/dts/comtrend,ar-5387un.dts
+++ b/arch/mips/dts/comtrend,ar-5387un.dts
@@ -51,6 +51,18 @@
};
};
+&spi {
+ status = "okay";
+
+ spi-flash at 0 {
+ compatible = "spi-flash";
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <33333334>;
+ };
+};
+
&uart0 {
u-boot,dm-pre-reloc;
status = "okay";
diff --git a/configs/comtrend_ar5387un_ram_defconfig b/configs/comtrend_ar5387un_ram_defconfig
index b64018ae71..352f01d65b 100644
--- a/configs/comtrend_ar5387un_ram_defconfig
+++ b/configs/comtrend_ar5387un_ram_defconfig
@@ -26,6 +26,8 @@ CONFIG_CMD_MEMINFO=y
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
# CONFIG_CMD_NET is not set
# CONFIG_CMD_NFS is not set
# CONFIG_CMD_MISC is not set
@@ -34,6 +36,10 @@ CONFIG_DM_GPIO=y
CONFIG_LED=y
CONFIG_LED_BCM6328=y
CONFIG_LED_BLINK=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_MTD=y
CONFIG_POWER_DOMAIN=y
CONFIG_BCM6328_POWER_DOMAIN=y
CONFIG_DM_RESET=y
@@ -41,3 +47,5 @@ CONFIG_RESET_BCM6345=y
# CONFIG_SPL_SERIAL_PRESENT is not set
CONFIG_DM_SERIAL=y
CONFIG_BCM6345_SERIAL=y
+CONFIG_DM_SPI=y
+CONFIG_BCM63XX_HSSPI=y
--
2.11.0
^ permalink raw reply related [flat|nested] 45+ messages in thread
* [U-Boot] [PATCH v6 0/4] mips: bmips: add HSSPI support
2018-01-20 1:13 ` [U-Boot] [PATCH v6 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
` (3 preceding siblings ...)
2018-01-20 1:13 ` [U-Boot] [PATCH v6 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un Álvaro Fernández Rojas
@ 2018-01-22 5:11 ` Jagan Teki
4 siblings, 0 replies; 45+ messages in thread
From: Jagan Teki @ 2018-01-22 5:11 UTC (permalink / raw)
To: u-boot
On Sat, Jan 20, 2018 at 6:43 AM, Álvaro Fernández Rojas
<noltari@gmail.com> wrote:
> BCM63xx HSSPI controller has the same issue as BCM63xx SPI controller: it
> doesn't allow keeping CS active between transfers.
> However, this controller allows changing CS polarities, which is used in the
> linux upstream driver to manage CS as desired.
>
> v6: Introduce changes suggested by Simon Glass:
> - Fix defconfig order.
> v5: Introduce changes suggested by Jagan Teki:
> - Rename SPI_PP_ macros.
> - cs_activate instead of claim_cs.
> - deactivate_cs instead of release_cs.
> - Use wait_for_bit_be32 instead of infinite loop.
> v4: Sync with master.
> v3: Switch to CONFIG_BCM63XX_HSSPI and rebase on top of SPI v4.
> v2: Introduce changes suggested by Simon Glass:
> - Split bcm63xx_hsspi_xfer() into smaller functions.
> - Check possible clock errors.
> - Check possible reset errors.
> - Switch to devfdt_get_addr_size_index().
> - Use setbits32_be() for clock gate.
>
> Álvaro Fernández Rojas (4):
> dm: spi: add BCM63xx HSSPI driver
> mips: bmips: add bcm63xx-hsspi driver support for BCM6328
> mips: bmips: add bcm63xx-hsspi driver support for BCM63268
> mips: bmips: enable the SPI flash on the Comtrend AR-5387un
Applied to u-boot-spi/master, thanks!
^ permalink raw reply [flat|nested] 45+ messages in thread
end of thread, other threads:[~2018-01-22 5:11 UTC | newest]
Thread overview: 45+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2017-05-23 19:18 [U-Boot] [PATCH 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
2017-05-23 19:18 ` [U-Boot] [PATCH 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
2017-06-01 3:10 ` Simon Glass
2017-05-23 19:18 ` [U-Boot] [PATCH 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328 Álvaro Fernández Rojas
2017-06-01 3:10 ` Simon Glass
2017-05-23 19:18 ` [U-Boot] [PATCH 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268 Álvaro Fernández Rojas
2017-06-01 3:10 ` Simon Glass
2017-05-23 19:18 ` [U-Boot] [PATCH 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un Álvaro Fernández Rojas
2017-06-01 3:10 ` Simon Glass
2017-06-03 10:15 ` [U-Boot] [PATCH v2 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
2017-06-03 10:16 ` [U-Boot] [PATCH v2 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
2017-06-04 9:02 ` Daniel Schwierzeck
2017-06-05 16:03 ` Álvaro Fernández Rojas
2017-06-03 10:16 ` [U-Boot] [PATCH v2 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328 Álvaro Fernández Rojas
2017-06-04 9:04 ` Daniel Schwierzeck
2017-06-05 16:04 ` Álvaro Fernández Rojas
2017-06-03 10:16 ` [U-Boot] [PATCH v2 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268 Álvaro Fernández Rojas
2017-06-04 9:04 ` Daniel Schwierzeck
2017-06-05 16:04 ` Álvaro Fernández Rojas
2017-06-03 10:16 ` [U-Boot] [PATCH v2 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un Álvaro Fernández Rojas
2017-06-04 9:05 ` Daniel Schwierzeck
2017-06-05 16:04 ` Álvaro Fernández Rojas
2017-06-14 9:59 ` [U-Boot] [PATCH v3 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
2017-06-14 9:59 ` [U-Boot] [PATCH v3 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
2017-06-14 9:59 ` [U-Boot] [PATCH v3 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328 Álvaro Fernández Rojas
2017-06-14 9:59 ` [U-Boot] [PATCH v3 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268 Álvaro Fernández Rojas
2017-06-14 9:59 ` [U-Boot] [PATCH v3 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un Álvaro Fernández Rojas
2017-07-30 12:14 ` [U-Boot] [PATCH v4 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
2017-07-30 12:14 ` [U-Boot] [PATCH v4 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
2017-08-11 9:42 ` Jagan Teki
2017-12-26 13:20 ` Álvaro Fernández Rojas
2017-07-30 12:14 ` [U-Boot] [PATCH v4 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328 Álvaro Fernández Rojas
2017-07-30 12:14 ` [U-Boot] [PATCH v4 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268 Álvaro Fernández Rojas
2017-07-30 12:14 ` [U-Boot] [PATCH v4 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un Álvaro Fernández Rojas
2018-01-15 18:45 ` [U-Boot] [PATCH v5 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
2018-01-15 18:45 ` [U-Boot] [PATCH v5 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
2018-01-15 18:45 ` [U-Boot] [PATCH v5 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328 Álvaro Fernández Rojas
2018-01-15 18:45 ` [U-Boot] [PATCH v5 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268 Álvaro Fernández Rojas
2018-01-15 18:45 ` [U-Boot] [PATCH v5 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un Álvaro Fernández Rojas
2018-01-20 1:13 ` [U-Boot] [PATCH v6 0/4] mips: bmips: add HSSPI support Álvaro Fernández Rojas
2018-01-20 1:13 ` [U-Boot] [PATCH v6 1/4] dm: spi: add BCM63xx HSSPI driver Álvaro Fernández Rojas
2018-01-20 1:13 ` [U-Boot] [PATCH v6 2/4] mips: bmips: add bcm63xx-hsspi driver support for BCM6328 Álvaro Fernández Rojas
2018-01-20 1:13 ` [U-Boot] [PATCH v6 3/4] mips: bmips: add bcm63xx-hsspi driver support for BCM63268 Álvaro Fernández Rojas
2018-01-20 1:13 ` [U-Boot] [PATCH v6 4/4] mips: bmips: enable the SPI flash on the Comtrend AR-5387un Álvaro Fernández Rojas
2018-01-22 5:11 ` [U-Boot] [PATCH v6 0/4] mips: bmips: add HSSPI support Jagan Teki
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).