[U-Boot] [PATCH v2 05/20] spl: nand: sunxi: introduce the nand_wait_int() helper

[Boris Brezillon <boris.brezillon@bootlin.com>]

On Thu, 22 Feb 2018 14:33:35 +0100
Miquel Raynal <miquel.raynal@bootlin.com> wrote:

> The pattern of polling on a status register until a bit is set or a
> timeout occurs is repeated multiple times in the driver. Mutualize the
> code by introducing the nand_wait_int() helper that does wait for the
> bit to flip or returns an error in case of timeout.
> 
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> ---
>  drivers/mtd/nand/sunxi_nand_spl.c | 33 ++++++++++++++-------------------
>  1 file changed, 14 insertions(+), 19 deletions(-)
> 
> diff --git a/drivers/mtd/nand/sunxi_nand_spl.c b/drivers/mtd/nand/sunxi_nand_spl.c
> index 608cc997ca..afb5fef0a6 100644
> --- a/drivers/mtd/nand/sunxi_nand_spl.c
> +++ b/drivers/mtd/nand/sunxi_nand_spl.c
> @@ -155,6 +155,17 @@ static inline int check_value_negated(int offset, int unexpected_bits,
>  	return check_value_inner(offset, unexpected_bits, timeout_us, 1);
>  }
>  
> +static int nand_wait_int(void)
> +{
> +	if (!check_value(SUNXI_NFC_BASE + NFC_ST, NFC_ST_CMD_INT_FLAG,
> +			 DEFAULT_TIMEOUT_US)) {
> +		printf("nand: timeout waiting for interruption\n");
> +		return -ETIMEDOUT;
> +	}
> +
> +	return 0;
> +}
> +
>  void nand_init(void)
>  {
>  	uint32_t val;
> @@ -176,12 +187,7 @@ void nand_init(void)
>  	writel(NFC_SEND_CMD1 | NFC_WAIT_FLAG | NAND_CMD_RESET,
>  	       SUNXI_NFC_BASE + NFC_CMD);
>  
> -	if (!check_value(SUNXI_NFC_BASE + NFC_ST, NFC_ST_CMD_INT_FLAG,
> -			 DEFAULT_TIMEOUT_US)) {
> -		printf("Error timeout waiting for nand reset\n");
> -		return;
> -	}
> -	writel(NFC_ST_CMD_INT_FLAG, SUNXI_NFC_BASE + NFC_ST);
> +	nand_wait_int();
>  }
>  
>  static void nand_apply_config(const struct nfc_config *conf)
> @@ -211,13 +217,7 @@ static int nand_load_page(const struct nfc_config *conf, u32 offs)
>  	       ((conf->addr_cycles - 1) << NFC_ADDR_NUM_OFFSET) | NFC_SEND_ADDR,
>  	       SUNXI_NFC_BASE + NFC_CMD);
>  
> -	if (!check_value(SUNXI_NFC_BASE + NFC_ST, NFC_ST_CMD_INT_FLAG,
> -			 DEFAULT_TIMEOUT_US)) {
> -		printf("Error while initializing dma interrupt\n");
> -		return -EIO;
> -	}
> -
> -	return 0;
> +	return nand_wait_int();
>  }
>  
>  static int nand_reset_column(void)
> @@ -231,13 +231,8 @@ static int nand_reset_column(void)
>  	       (1 << NFC_ADDR_NUM_OFFSET) | NFC_SEND_ADDR | NFC_CMD_RNDOUT,
>  	       SUNXI_NFC_BASE + NFC_CMD);
>  
> -	if (!check_value(SUNXI_NFC_BASE + NFC_ST, NFC_ST_CMD_INT_FLAG,
> -			 DEFAULT_TIMEOUT_US)) {
> -		printf("Error while initializing dma interrupt\n");
> -		return -1;
> -	}
> +	return nand_wait_int();
>  

You can drop this empty line.

> -	return 0;
>  }
>  
>  static int nand_read_page(const struct nfc_config *conf, u32 offs,



-- 
Boris Brezillon, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
https://bootlin.com