[U-Boot] [PATCH] arm: zynq: dts: add spi flash node to zedboard

[U-Boot] [PATCH] arm: zynq: dts: add spi flash node to zedboard

[Luis Araneda]

Add a flash node to fix the detection of the memory IC.
With the changes introduced with commit 8fee8845e754
("enf_sf: reuse setup_flash_device instead of open coding it")
the SPI speed is now read from device-tree or a default value
is applied. This replaced the old behavior of setting the
SPI speed to CONFIG_ENV_SPI_MAX_HZ.

As this board didn't have a flash node, the default value
was applied to the SPI speed, producing an error when probing
the flash memory (speed too slow).

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
---
 arch/arm/dts/zynq-zed.dts | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/dts/zynq-zed.dts b/arch/arm/dts/zynq-zed.dts
index 24eccf1633..9c505fb7b8 100644
--- a/arch/arm/dts/zynq-zed.dts
+++ b/arch/arm/dts/zynq-zed.dts
@@ -51,6 +51,13 @@
 &qspi {
 	u-boot,dm-pre-reloc;
 	status = "okay";
+	num-cs = <1>;
+	flash at 0 {
+		compatible = "spansion,s25fl256s", "spi-flash";
+		reg = <0>;
+		spi-max-frequency = <30000000>;
+		m25p,fast-read;
+	};
 };
 
 &sdhci0 {
-- 
2.18.0

[U-Boot] [PATCH] arm: zynq: dts: add spi flash node to zedboard

[Michal Simek]

On 27.7.2018 10:43, Luis Araneda wrote:
> Add a flash node to fix the detection of the memory IC.
> With the changes introduced with commit 8fee8845e754
> ("enf_sf: reuse setup_flash_device instead of open coding it")
> the SPI speed is now read from device-tree or a default value
> is applied. This replaced the old behavior of setting the
> SPI speed to CONFIG_ENV_SPI_MAX_HZ.
> 
> As this board didn't have a flash node, the default value
> was applied to the SPI speed, producing an error when probing
> the flash memory (speed too slow).
> 
> Signed-off-by: Luis Araneda <luaraneda@gmail.com>
> ---
>  arch/arm/dts/zynq-zed.dts | 7 +++++++
>  1 file changed, 7 insertions(+)
> 
> diff --git a/arch/arm/dts/zynq-zed.dts b/arch/arm/dts/zynq-zed.dts
> index 24eccf1633..9c505fb7b8 100644
> --- a/arch/arm/dts/zynq-zed.dts
> +++ b/arch/arm/dts/zynq-zed.dts
> @@ -51,6 +51,13 @@
>  &qspi {
>  	u-boot,dm-pre-reloc;
>  	status = "okay";
> +	num-cs = <1>;
> +	flash at 0 {
> +		compatible = "spansion,s25fl256s", "spi-flash";
> +		reg = <0>;
> +		spi-max-frequency = <30000000>;
> +		m25p,fast-read;
> +	};
>  };
>  
>  &sdhci0 {
> 

Applied.
M