* [U-Boot] [RFC PATCH] arm: zynq: read mac address from SPI flash memory
@ 2018-08-14 4:55 Luis Araneda
2018-08-14 14:07 ` Michal Simek
0 siblings, 1 reply; 3+ messages in thread
From: Luis Araneda @ 2018-08-14 4:55 UTC (permalink / raw)
To: u-boot
Implement a method for reading the MAC address from an
SPI flash memory.
In particular, this method is used by the Zybo Z7 board
to read the MAC address from the OTP region in the SPI NOR
memory
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
---
I'm trying to implement the reading of the MAC address of
the Zybo Z7 board from the OTP region of its SPI NOR memory.
I took some ideas from Digilent's fork, but the commit was
marked as not upstremeable. That's why I'm asking for comments.
If the code can't be merged, ideas on how this can be implemented
are welcome.
Thanks,
Luis Araneda.
---
board/xilinx/zynq/board.c | 28 ++++++++++++++++++++++++++++
configs/zynq_zybo_z7_defconfig | 3 +++
drivers/misc/Kconfig | 17 +++++++++++++++++
3 files changed, 48 insertions(+)
diff --git a/board/xilinx/zynq/board.c b/board/xilinx/zynq/board.c
index 614d93c082..a252c38956 100644
--- a/board/xilinx/zynq/board.c
+++ b/board/xilinx/zynq/board.c
@@ -6,9 +6,12 @@
#include <common.h>
#include <dm/uclass.h>
+#include <dm/device.h>
+#include <dm/device-internal.h>
#include <fdtdec.h>
#include <fpga.h>
#include <mmc.h>
+#include <spi_flash.h>
#include <watchdog.h>
#include <wdt.h>
#include <zynqpl.h>
@@ -87,6 +90,31 @@ int zynq_board_read_rom_ethaddr(unsigned char *ethaddr)
printf("I2C EEPROM MAC address read failed\n");
#endif
+#if defined(CONFIG_MAC_ADDR_IN_SPI_FLASH)
+ struct spi_flash *flash;
+ struct udevice *dev;
+ int ret;
+
+ ret = spi_flash_probe_bus_cs(CONFIG_SF_DEFAULT_BUS,
+ CONFIG_SF_DEFAULT_CS,
+ 0, 0, &dev);
+ if (ret) {
+ printf("SPI(bus:%u cs:%u) probe failed\n",
+ CONFIG_SF_DEFAULT_BUS,
+ CONFIG_SF_DEFAULT_CS);
+ return 0;
+ }
+
+ flash = dev_get_uclass_priv(dev);
+ flash->read_cmd = CONFIG_MAC_ADDR_SPI_FLASH_READ_CMD;
+
+ if (spi_flash_read_dm(dev,
+ CONFIG_MAC_ADDR_SPI_FLASH_DATA_OFFSET,
+ 6, ethaddr))
+ printf("SPI MAC address read failed\n");
+
+ device_remove(dev, DM_REMOVE_NORMAL);
+#endif
return 0;
}
diff --git a/configs/zynq_zybo_z7_defconfig b/configs/zynq_zybo_z7_defconfig
index ad44e772aa..ca402e3231 100644
--- a/configs/zynq_zybo_z7_defconfig
+++ b/configs/zynq_zybo_z7_defconfig
@@ -44,6 +44,9 @@ CONFIG_DM_GPIO=y
CONFIG_SYS_I2C_ZYNQ=y
CONFIG_ZYNQ_I2C0=y
CONFIG_ZYNQ_I2C1=y
+CONFIG_MAC_ADDR_IN_SPI_FLASH=y
+CONFIG_MAC_ADDR_SPI_FLASH_READ_CMD=0x4b
+CONFIG_MAC_ADDR_SPI_FLASH_DATA_OFFSET=0x20
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
index c031dfde9d..40cec81e66 100644
--- a/drivers/misc/Kconfig
+++ b/drivers/misc/Kconfig
@@ -272,6 +272,23 @@ config SYS_I2C_EEPROM_ADDR_OVERFLOW
endif
+config MAC_ADDR_IN_SPI_FLASH
+ bool "MAC address in SPI flash"
+ help
+ Read MAC address from an SPI flash memory
+
+if MAC_ADDR_IN_SPI_FLASH
+
+config MAC_ADDR_SPI_FLASH_READ_CMD
+ hex "Read command for the SPI flash memory"
+ default 0
+
+config MAC_ADDR_SPI_FLASH_DATA_OFFSET
+ hex "Offset of MAC data in SPI flash memory"
+ default 0
+
+endif
+
config GDSYS_RXAUI_CTRL
bool "Enable gdsys RXAUI control driver"
depends on MISC
--
2.18.0
^ permalink raw reply related [flat|nested] 3+ messages in thread* [U-Boot] [RFC PATCH] arm: zynq: read mac address from SPI flash memory
2018-08-14 4:55 [U-Boot] [RFC PATCH] arm: zynq: read mac address from SPI flash memory Luis Araneda
@ 2018-08-14 14:07 ` Michal Simek
2018-08-16 6:04 ` Luis Araneda
0 siblings, 1 reply; 3+ messages in thread
From: Michal Simek @ 2018-08-14 14:07 UTC (permalink / raw)
To: u-boot
Hi Luis, +Jagan,
On 14.8.2018 06:55, Luis Araneda wrote:
> Implement a method for reading the MAC address from an
> SPI flash memory.
> In particular, this method is used by the Zybo Z7 board
> to read the MAC address from the OTP region in the SPI NOR
> memory
>
> Signed-off-by: Luis Araneda <luaraneda@gmail.com>
> ---
>
> I'm trying to implement the reading of the MAC address of
> the Zybo Z7 board from the OTP region of its SPI NOR memory.
>
> I took some ideas from Digilent's fork, but the commit was
> marked as not upstremeable. That's why I'm asking for comments.
I have done this code long time ago because there was a work which
wasn't finished. Also upstreaming takes some time to finish.
>
> If the code can't be merged, ideas on how this can be implemented
> are welcome.
>
> Thanks,
>
> Luis Araneda.
>
> ---
> board/xilinx/zynq/board.c | 28 ++++++++++++++++++++++++++++
> configs/zynq_zybo_z7_defconfig | 3 +++
> drivers/misc/Kconfig | 17 +++++++++++++++++
> 3 files changed, 48 insertions(+)
>
> diff --git a/board/xilinx/zynq/board.c b/board/xilinx/zynq/board.c
> index 614d93c082..a252c38956 100644
> --- a/board/xilinx/zynq/board.c
> +++ b/board/xilinx/zynq/board.c
> @@ -6,9 +6,12 @@
>
> #include <common.h>
> #include <dm/uclass.h>
> +#include <dm/device.h>
> +#include <dm/device-internal.h>
> #include <fdtdec.h>
> #include <fpga.h>
> #include <mmc.h>
> +#include <spi_flash.h>
> #include <watchdog.h>
> #include <wdt.h>
> #include <zynqpl.h>
> @@ -87,6 +90,31 @@ int zynq_board_read_rom_ethaddr(unsigned char *ethaddr)
> printf("I2C EEPROM MAC address read failed\n");
> #endif
>
> +#if defined(CONFIG_MAC_ADDR_IN_SPI_FLASH)
> + struct spi_flash *flash;
> + struct udevice *dev;
> + int ret;
> +
> + ret = spi_flash_probe_bus_cs(CONFIG_SF_DEFAULT_BUS,
> + CONFIG_SF_DEFAULT_CS,
> + 0, 0, &dev);
> + if (ret) {
> + printf("SPI(bus:%u cs:%u) probe failed\n",
> + CONFIG_SF_DEFAULT_BUS,
> + CONFIG_SF_DEFAULT_CS);
> + return 0;
> + }
> +
> + flash = dev_get_uclass_priv(dev);
> + flash->read_cmd = CONFIG_MAC_ADDR_SPI_FLASH_READ_CMD;
> +
> + if (spi_flash_read_dm(dev,
> + CONFIG_MAC_ADDR_SPI_FLASH_DATA_OFFSET,
> + 6, ethaddr))
> + printf("SPI MAC address read failed\n");
> +
> + device_remove(dev, DM_REMOVE_NORMAL);
> +#endif
> return 0;
> }
>
> diff --git a/configs/zynq_zybo_z7_defconfig b/configs/zynq_zybo_z7_defconfig
> index ad44e772aa..ca402e3231 100644
> --- a/configs/zynq_zybo_z7_defconfig
> +++ b/configs/zynq_zybo_z7_defconfig
> @@ -44,6 +44,9 @@ CONFIG_DM_GPIO=y
> CONFIG_SYS_I2C_ZYNQ=y
> CONFIG_ZYNQ_I2C0=y
> CONFIG_ZYNQ_I2C1=y
> +CONFIG_MAC_ADDR_IN_SPI_FLASH=y
> +CONFIG_MAC_ADDR_SPI_FLASH_READ_CMD=0x4b
I am doing spi but isn't this any standard OTP read command which should
put to spi framework.
> +CONFIG_MAC_ADDR_SPI_FLASH_DATA_OFFSET=0x20
> CONFIG_MMC_SDHCI=y
> CONFIG_MMC_SDHCI_ZYNQ=y
> CONFIG_SPI_FLASH=y
> diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
> index c031dfde9d..40cec81e66 100644
> --- a/drivers/misc/Kconfig
> +++ b/drivers/misc/Kconfig
> @@ -272,6 +272,23 @@ config SYS_I2C_EEPROM_ADDR_OVERFLOW
>
> endif
>
> +config MAC_ADDR_IN_SPI_FLASH
> + bool "MAC address in SPI flash"
> + help
> + Read MAC address from an SPI flash memory
> +
> +if MAC_ADDR_IN_SPI_FLASH
> +
> +config MAC_ADDR_SPI_FLASH_READ_CMD
> + hex "Read command for the SPI flash memory"
> + default 0
> +
> +config MAC_ADDR_SPI_FLASH_DATA_OFFSET
> + hex "Offset of MAC data in SPI flash memory"
> + default 0
> +
> +endif
> +
> config GDSYS_RXAUI_CTRL
> bool "Enable gdsys RXAUI control driver"
> depends on MISC
>
Thanks,
Michal
^ permalink raw reply [flat|nested] 3+ messages in thread* [U-Boot] [RFC PATCH] arm: zynq: read mac address from SPI flash memory
2018-08-14 14:07 ` Michal Simek
@ 2018-08-16 6:04 ` Luis Araneda
0 siblings, 0 replies; 3+ messages in thread
From: Luis Araneda @ 2018-08-16 6:04 UTC (permalink / raw)
To: u-boot
Hi,
On Tue, Aug 14, 2018 at 11:07 AM Michal Simek <michal.simek@xilinx.com> wrote:
> On 14.8.2018 06:55, Luis Araneda wrote:
> > Implement a method for reading the MAC address from an
> > SPI flash memory.
> > In particular, this method is used by the Zybo Z7 board
> > to read the MAC address from the OTP region in the SPI NOR
> > memory
> > [...]
> > +#if defined(CONFIG_MAC_ADDR_IN_SPI_FLASH)
> > + struct spi_flash *flash;
> > + struct udevice *dev;
> > + int ret;
> > +
> > + ret = spi_flash_probe_bus_cs(CONFIG_SF_DEFAULT_BUS,
> > + CONFIG_SF_DEFAULT_CS,
> > + 0, 0, &dev);
> > + if (ret) {
> > + printf("SPI(bus:%u cs:%u) probe failed\n",
> > + CONFIG_SF_DEFAULT_BUS,
> > + CONFIG_SF_DEFAULT_CS);
> > + return 0;
> > + }
> > +
> > + flash = dev_get_uclass_priv(dev);
> > + flash->read_cmd = CONFIG_MAC_ADDR_SPI_FLASH_READ_CMD;
> > +
> > + if (spi_flash_read_dm(dev,
> > + CONFIG_MAC_ADDR_SPI_FLASH_DATA_OFFSET,
> > + 6, ethaddr))
> > + printf("SPI MAC address read failed\n");
> > +
> > + device_remove(dev, DM_REMOVE_NORMAL);
> > +#endif
> > return 0;
> > }
> >
> > diff --git a/configs/zynq_zybo_z7_defconfig b/configs/zynq_zybo_z7_defconfig
> > index ad44e772aa..ca402e3231 100644
> > --- a/configs/zynq_zybo_z7_defconfig
> > +++ b/configs/zynq_zybo_z7_defconfig
> > @@ -44,6 +44,9 @@ CONFIG_DM_GPIO=y
> > CONFIG_SYS_I2C_ZYNQ=y
> > CONFIG_ZYNQ_I2C0=y
> > CONFIG_ZYNQ_I2C1=y
> > +CONFIG_MAC_ADDR_IN_SPI_FLASH=y
> > +CONFIG_MAC_ADDR_SPI_FLASH_READ_CMD=0x4b
>
> I am doing spi but isn't this any standard OTP read command which should
> put to spi framework.
I'm not sure if there is an standard OTP read command, they might be
vendor/model specific.
Jagan, is this possible currently, or might it be covered by the new
SPI-mem/SPI-NAND code?
In order to keep this moving, I would like to get some specific
question answered:
1: Should the final code be in the "zynq_board_read_rom_ethaddr"
function like it is now?
2: On an ideal solution, should I remove the probing and read_cmd, and
call a function to read from OTP at a certain offset? In that case the
CONFIG_MAC_ADDR_SPI_FLASH_READ_CMD would't be necessary.
3: Is the CONFIG_MAC_ADDR_IN_SPI_FLASH an acceptable solution to
enable the feature?
Thanks,
Luis Araneda.
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2018-08-16 6:04 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2018-08-14 4:55 [U-Boot] [RFC PATCH] arm: zynq: read mac address from SPI flash memory Luis Araneda
2018-08-14 14:07 ` Michal Simek
2018-08-16 6:04 ` Luis Araneda
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox