From: Tom Rini <trini@konsulko.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [U-Boot, v3, 7/7] ARM: dts: k2g-ice: add dt node for netcp
Date: Fri, 12 Apr 2019 12:30:07 -0400 [thread overview]
Message-ID: <20190412163007.GW4664@bill-the-cat> (raw)
In-Reply-To: <20190221170207.17808-8-m-karicheri2@ti.com>
On Thu, Feb 21, 2019 at 12:02:07PM -0500, Murali Karicheri wrote:
> This patch adds dt node for DP83867 phy used on K2G ICE board and
> also enable netcp device nodes for the board.
>
> EVM hardware spec recommends to add 0.25 nsec delay in the tx
> direction and 2.25 nsec delay in the rx direction for internal
> delay in the clock path to be on the safer side.
>
> The board straps RX_DV/RX_CTRL pin of on board DP83867 phy in mode
> 1. Unfortunately, the phy data manual disallows this. Add
> ti,dp83867-rxctrl-strap-quirk in the phy node to allow software to
> enable workaround suggested for this incorrect strap setting. This
> ensures proper operation of this PHY.
>
> The dts bindings are kept in sync with that from 4.14.y linux
> kernel. This required the pinmux device related bindings to be
> commented out to allow for compilation.
>
> Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Applied to u-boot/master, thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190412/fc27b75f/attachment.sig>
next prev parent reply other threads:[~2019-04-12 16:30 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-02-21 17:02 [U-Boot] [PATCH v3 0/7] Add netcp networking support on K2G ICE EVM Murali Karicheri
2019-02-21 17:02 ` [U-Boot] [PATCH v3 1/7] ARM: k2g-ice: Add pinmux support for rgmii interface Murali Karicheri
2019-02-25 18:24 ` Joe Hershberger
2019-02-25 18:29 ` Joe Hershberger
2019-04-12 16:29 ` [U-Boot] [U-Boot, v3, " Tom Rini
2019-02-21 17:02 ` [U-Boot] [PATCH v3 2/7] ARM: k2g-gp-evm: update to rgmii pinmux configuration Murali Karicheri
2019-02-25 18:25 ` Joe Hershberger
2019-04-12 16:29 ` [U-Boot] [U-Boot, v3, " Tom Rini
2019-02-21 17:02 ` [U-Boot] [PATCH v3 3/7] net: netcp: add support for phy with rgmii ids Murali Karicheri
2019-02-25 18:26 ` Joe Hershberger
2019-04-12 16:29 ` [U-Boot] [U-Boot, v3, " Tom Rini
2019-02-21 17:02 ` [U-Boot] [PATCH v3 4/7] ARM: k2g: add a workaround to reset the phy Murali Karicheri
2019-02-25 18:28 ` Joe Hershberger
2019-04-12 16:29 ` [U-Boot] [U-Boot, v3, " Tom Rini
2019-02-21 17:02 ` [U-Boot] [PATCH v3 5/7] ARM: dts: k2g-evm: remove unused phy-mode property from phy node Murali Karicheri
2019-02-25 18:36 ` Joe Hershberger
2019-04-12 16:29 ` [U-Boot] [U-Boot, v3, " Tom Rini
2019-02-21 17:02 ` [U-Boot] [PATCH v3 6/7] k2g: config enable ti phy dp83867 for k2g Murali Karicheri
2019-02-21 23:10 ` Tom Rini
2019-02-25 18:35 ` Joe Hershberger
2019-04-12 16:30 ` [U-Boot] [U-Boot, v3, " Tom Rini
2019-02-21 17:02 ` [U-Boot] [PATCH v3 7/7] ARM: dts: k2g-ice: add dt node for netcp Murali Karicheri
2019-02-25 18:30 ` Joe Hershberger
2019-04-12 16:30 ` Tom Rini [this message]
2019-02-25 16:18 ` [U-Boot] [PATCH v3 0/7] Add netcp networking support on K2G ICE EVM Murali Karicheri
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190412163007.GW4664@bill-the-cat \
--to=trini@konsulko.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).