[U-Boot] [PATCH 3/4] zynq_minized: Add configuration header file for board specific environment.

Philip Balister
2019-04-17T17:46:29Z

Signed-off-by: Philip Balister <philip@opensdr.com>
---
include/configs/zynq_minized.h | 54 ++++++++++++++++++++++++++++++++++
1 file changed, 54 insertions(+)
create mode 100644 include/configs/zynq_minized.h

diff --git a/include/configs/zynq_minized.h b/include/configs/zynq_minized.h
new file mode 100644
index 0000000000..6d89e3da29
--- /dev/null
+++ b/include/configs/zynq_minized.h
@@ -0,0 +1,54 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * (C) Copyright 2019 Philip Balister <philip@balister.org>.
+ *
+ * Configuration settings for the MiniZed board
+ * See zynq-common.h for Zynq common configs
+ */
+
+#ifndef __CONFIG_ZYNQ_MINIZED_H
+#define __CONFIG_ZYNQ_MINIZED_H
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "fit_image=fitImage\0" \
+ "bit_file=fpga.bit\0" \
+ "load_addr=0x2000000\0" \
+ "fit_size=0x800000\0" \
+ "flash_off=0x100000\0" \
+ "nor_flash_off=0xE2100000\0" \
+ "fdt_high=0x20000000\0" \
+ "initrd_high=0x20000000\0" \
+ "loadbootenv_addr=0x2000000\0" \
+ "fdt_addr_r=0x1f00000\0" \
+ "kernel_addr_r=0x2000000\0" \
+ "ramdisk_addr_r=0x3100000\0" \
+ "bootenv=uEnv.txt\0" \
+ "bootenv_dev=mmc\0" \
+ "qspiboot=echo Copying FIT from QSPI to RAM... (Not Yet) \0" \
+ "mmcboot= " \
+ "echo Copying fpga.bit from MMC and loading FPGA... && " \
+ "load mmc 0:1 ${load_addr} /boot/${bit_file} && " \
+ "fpga loadb 0 ${load_addr} ${filesize} && " \
+ "echo Copying FIT from MMC to RAM... && " \
+ "load mmc 0:1 ${load_addr} /boot/${fit_image} && " \
+ "setenv bootargs root=/dev/mmcblk1p1 rootwait && " \
+ "bootm ${load_addr}\0" \
+ "usbboot=if usb start; then " \
+ "echo Copying fpga.bit from USB and loading FPGA... && " \
+ "load usb 0 ${load_addr} /boot/${bit_file} && " \
+ "fpga loadb 0 ${load_addr} ${filesize} && " \
+ "echo Copying FIT from USB to RAM... && " \
+ "load usb 0 ${load_addr} /boot/${fit_image} && " \
+ "setenv bootargs root=/dev/sda1 rootwait && " \
+ "bootm ${load_addr}; fi\0" \
+ "usbrecover=if usb start; then " \
+ "echo Copying fpga.bit from USB and loading FPGA... && " \
+ "load usb 0 ${load_addr} ${bit_file} && " \
+ "fpga loadb 0 ${load_addr} ${filesize} && " \
+ "echo Copying FIT from USB to RAM... && " \
+ "load usb 0 ${load_addr} ${fit_image} && " \
+ "bootm ${load_addr}; fi\0"
+
+#include <configs/zynq-common.h>
+
+#endif /* __CONFIG_ZYNQ_MINIZED_H */
--
2.20.1