From: Andreas Dannenberg <dannenberg@ti.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 00/18] Add EEPROM-based board detect support for TI
Date: Wed, 8 May 2019 16:37:33 -0500 [thread overview]
Message-ID: <20190508213751.23179-1-dannenberg@ti.com> (raw)
This series adds the pieces needed to fully configure the TI AM654x EVM
and its associated (optional) daughtercards using a GPIO-based card
presence detection scheme. It then reads out and parses any I2C EEPROM
data present on any such boards for example board name, serial #,
Ethernet MAC addresses, etc. and incorporates this data into the current
U-Boot environment. One important aspect is the application of
daughercard-specific DTB overlays right before the Kernel boot happens.
This series also adds basic I2C support for TI K3 family devices which
is a prerequisite for the EEPROM access.
--
Andreas Dannenberg
Texas Instruments Inc
Andreas Dannenberg (16):
arm: dts: k3-am65: Move pinctrl nodes out of U-Boot specific dtsi
arm: dts: k3-am65: Add I2C nodes
arm: dts: k3-am654-base-board: Enable wkup_i2c0 across all boot stages
configs: am65x_evm_defconfig: Enable I2C support
configs: am65x_hs_evm_defconfig: Enable I2C support
arm64: dts: k3-am654-base-board: Add I2C GPIO expander @ 0x38
configs: am65x_evm_a53: Enable PCA953X-type GPIO driver
configs: am65x_hs_evm_a53: Enable PCA953X-type GPIO driver
configs: am65x_evm_a53: Increase malloc pool before relocation
configs: am65x_hs_evm_a53: Increase malloc pool before relocation
arm: K3: am654: Map common EEPROM data into SRAM scratch space
ti: common: am6: Add support for board description EEPROM
ti: common: am6: Add support for setting MAC addresses
board: ti: am654: Use EEPROM-based board detection
configs: am65x_evm: Add support for applying overlays
configs: am65x_hs_evm: Add support for applying overlays
Vignesh R (2):
i2c: omap24xx_i2c: Adapt driver to support K3 devices
arm: omap_i2c: Remove unwanted header file inclusion
arch/arm/dts/k3-am65-main.dtsi | 60 +++++
arch/arm/dts/k3-am65-mcu.dtsi | 11 +
arch/arm/dts/k3-am65-wakeup.dtsi | 19 ++
arch/arm/dts/k3-am65.dtsi | 7 +
arch/arm/dts/k3-am654-base-board-u-boot.dtsi | 35 +--
arch/arm/dts/k3-am654-base-board.dts | 22 ++
arch/arm/dts/k3-am654-r5-base-board.dts | 13 +
arch/arm/include/asm/omap_i2c.h | 2 -
arch/arm/mach-k3/am6_init.c | 4 +
arch/arm/mach-k3/include/mach/am6_hardware.h | 3 +
arch/arm/mach-k3/include/mach/sys_proto.h | 2 +
board/ti/am65x/Kconfig | 7 +
board/ti/am65x/evm.c | 241 ++++++++++++++++++
board/ti/common/board_detect.c | 246 +++++++++++++++++++
board/ti/common/board_detect.h | 206 ++++++++++++++++
configs/am65x_evm_a53_defconfig | 11 +-
configs/am65x_evm_r5_defconfig | 4 +
configs/am65x_hs_evm_a53_defconfig | 11 +-
configs/am65x_hs_evm_r5_defconfig | 4 +
drivers/i2c/Kconfig | 2 +-
include/configs/am65x_evm.h | 18 +-
21 files changed, 892 insertions(+), 36 deletions(-)
--
2.17.1
next reply other threads:[~2019-05-08 21:37 UTC|newest]
Thread overview: 27+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-05-08 21:37 Andreas Dannenberg [this message]
2019-05-08 21:37 ` [U-Boot] [PATCH 01/18] i2c: omap24xx_i2c: Adapt driver to support K3 devices Andreas Dannenberg
2019-05-09 11:19 ` Heiko Schocher
2019-05-08 21:37 ` [U-Boot] [PATCH 02/18] arm: omap_i2c: Remove unwanted header file inclusion Andreas Dannenberg
2019-05-09 11:20 ` Heiko Schocher
2019-05-08 21:37 ` [U-Boot] [PATCH 03/18] arm: dts: k3-am65: Move pinctrl nodes out of U-Boot specific dtsi Andreas Dannenberg
2019-05-08 21:37 ` [U-Boot] [PATCH 04/18] arm: dts: k3-am65: Add I2C nodes Andreas Dannenberg
2019-05-08 21:37 ` [U-Boot] [PATCH 05/18] arm: dts: k3-am654-base-board: Enable wkup_i2c0 across all boot stages Andreas Dannenberg
2019-05-08 21:37 ` [U-Boot] [PATCH 06/18] configs: am65x_evm_defconfig: Enable I2C support Andreas Dannenberg
2019-05-08 21:37 ` [U-Boot] [PATCH 07/18] configs: am65x_hs_evm_defconfig: " Andreas Dannenberg
2019-05-08 21:53 ` Andrew F. Davis
2019-05-08 21:37 ` [U-Boot] [PATCH 08/18] arm64: dts: k3-am654-base-board: Add I2C GPIO expander @ 0x38 Andreas Dannenberg
2019-05-08 21:37 ` [U-Boot] [PATCH 09/18] configs: am65x_evm_a53: Enable PCA953X-type GPIO driver Andreas Dannenberg
2019-05-08 21:37 ` [U-Boot] [PATCH 10/18] configs: am65x_hs_evm_a53: " Andreas Dannenberg
2019-05-08 21:37 ` [U-Boot] [PATCH 11/18] configs: am65x_evm_a53: Increase malloc pool before relocation Andreas Dannenberg
2019-05-08 21:37 ` [U-Boot] [PATCH 12/18] configs: am65x_hs_evm_a53: " Andreas Dannenberg
2019-05-08 21:37 ` [U-Boot] [PATCH 13/18] arm: K3: am654: Map common EEPROM data into SRAM scratch space Andreas Dannenberg
2019-05-09 3:52 ` Lokesh Vutla
2019-05-09 16:03 ` Andrew F. Davis
2019-05-09 16:27 ` Andreas Dannenberg
2019-05-15 20:11 ` Andreas Dannenberg
2019-05-08 21:37 ` [U-Boot] [PATCH 14/18] ti: common: am6: Add support for board description EEPROM Andreas Dannenberg
2019-05-08 21:37 ` [U-Boot] [PATCH 15/18] ti: common: am6: Add support for setting MAC addresses Andreas Dannenberg
2019-05-08 21:37 ` [U-Boot] [PATCH 16/18] board: ti: am654: Use EEPROM-based board detection Andreas Dannenberg
2019-05-08 21:37 ` [U-Boot] [PATCH 17/18] configs: am65x_evm: Add support for applying overlays Andreas Dannenberg
2019-05-08 21:37 ` [U-Boot] [PATCH 18/18] configs: am65x_hs_evm: " Andreas Dannenberg
2019-05-16 20:25 ` [U-Boot] [PATCH 00/18] Add EEPROM-based board detect support for TI Lokesh Vutla
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190508213751.23179-1-dannenberg@ti.com \
--to=dannenberg@ti.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox