[U-Boot] [v3, 5/5] mmc: fsl_esdhc_imx: drop useless code

[Lukasz Majewski <lukma@denx.de>]

On Tue, 21 May 2019 08:53:04 +0000
"Y.b. Lu" <yangbo.lu@nxp.com> wrote:

> Dropped useless code for i.MX eSDHC driver.
> 
> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
> ---
> Changes for v2:
> 	- Added this patch.
> Changes for v3:
> 	- None.
> ---
>  drivers/mmc/fsl_esdhc_imx.c | 96
> ++----------------------------------- include/fsl_esdhc_imx.h     |
> 4 -- 2 files changed, 4 insertions(+), 96 deletions(-)
> 
> diff --git a/drivers/mmc/fsl_esdhc_imx.c b/drivers/mmc/fsl_esdhc_imx.c
> index faf133390f..1c02e0eef1 100644
> --- a/drivers/mmc/fsl_esdhc_imx.c
> +++ b/drivers/mmc/fsl_esdhc_imx.c
> @@ -259,8 +259,7 @@ static int esdhc_setup_data(struct fsl_esdhc_priv
> *priv, struct mmc *mmc, {
>  	int timeout;
>  	struct fsl_esdhc *regs = priv->esdhc_regs;
> -#if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) || \
> -	defined(CONFIG_IMX8) || defined(CONFIG_IMX8M)
> +#if defined(CONFIG_S32V234) || defined(CONFIG_IMX8) ||
> defined(CONFIG_IMX8M) dma_addr_t addr;
>  #endif
>  	uint wml_value;
> @@ -273,8 +272,7 @@ static int esdhc_setup_data(struct fsl_esdhc_priv
> *priv, struct mmc *mmc, 
>  		esdhc_clrsetbits32(&regs->wml, WML_RD_WML_MASK,
> wml_value); #ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO
> -#if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) || \
> -	defined(CONFIG_IMX8) || defined(CONFIG_IMX8M)
> +#if defined(CONFIG_S32V234) || defined(CONFIG_IMX8) ||
> defined(CONFIG_IMX8M) addr = virt_to_phys((void *)(data->dest));
>  		if (upper_32_bits(addr))
>  			printf("Error found for upper 32 bits\n");
> @@ -310,8 +308,7 @@ static int esdhc_setup_data(struct fsl_esdhc_priv
> *priv, struct mmc *mmc, esdhc_clrsetbits32(&regs->wml,
> WML_WR_WML_MASK, wml_value << 16);
>  #ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO
> -#if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) || \
> -	defined(CONFIG_IMX8) || defined(CONFIG_IMX8M)
> +#if defined(CONFIG_S32V234) || defined(CONFIG_IMX8) ||
> defined(CONFIG_IMX8M) addr = virt_to_phys((void *)(data->src));
>  		if (upper_32_bits(addr))
>  			printf("Error found for upper 32 bits\n");
> @@ -376,8 +373,7 @@ static void check_and_invalidate_dcache_range
>  	unsigned end = 0;
>  	unsigned size = roundup(ARCH_DMA_MINALIGN,
>  				data->blocks*data->blocksize);
> -#if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) || \
> -	defined(CONFIG_IMX8) || defined(CONFIG_IMX8M)
> +#if defined(CONFIG_S32V234) || defined(CONFIG_IMX8) ||
> defined(CONFIG_IMX8M) dma_addr_t addr;
>  
>  	addr = virt_to_phys((void *)(data->dest));
> @@ -392,25 +388,6 @@ static void check_and_invalidate_dcache_range
>  	invalidate_dcache_range(start, end);
>  }
>  
> -#ifdef CONFIG_MCF5441x
> -/*
> - * Swaps 32-bit words to little-endian byte order.
> - */
> -static inline void sd_swap_dma_buff(struct mmc_data *data)
> -{
> -	int i, size = data->blocksize >> 2;
> -	u32 *buffer = (u32 *)data->dest;
> -	u32 sw;
> -
> -	while (data->blocks--) {
> -		for (i = 0; i < size; i++) {
> -			sw = __sw32(*buffer);
> -			*buffer++ = sw;
> -		}
> -	}
> -}
> -#endif
> -
>  /*
>   * Sends a command out on the bus.  Takes the mmc pointer,
>   * a command pointer, and an optional data pointer.
> @@ -575,9 +552,6 @@ static int esdhc_send_cmd_common(struct
> fsl_esdhc_priv *priv, struct mmc *mmc, */
>  		if (data->flags & MMC_DATA_READ) {
>  			check_and_invalidate_dcache_range(cmd, data);
> -#ifdef CONFIG_MCF5441x
> -			sd_swap_dma_buff(data);
> -#endif
>  		}
>  #endif
>  	}
> @@ -1073,12 +1047,8 @@ static int esdhc_init_common(struct
> fsl_esdhc_priv *priv, struct mmc *mmc) /* Disable the BRR and BWR
> bits in IRQSTAT */ esdhc_clrbits32(&regs->irqstaten, IRQSTATEN_BRR |
> IRQSTATEN_BWR); 
> -#ifdef CONFIG_MCF5441x
> -	esdhc_write32(&regs->proctl, PROCTL_INIT | PROCTL_D3CD);
> -#else
>  	/* Put the PROCTL reg back to the default */
>  	esdhc_write32(&regs->proctl, PROCTL_INIT);
> -#endif
>  
>  	/* Set timout to the maximum value */
>  	esdhc_clrsetbits32(&regs->sysctl, SYSCTL_TIMEOUT_MASK, 14 <<
> 16); @@ -1186,11 +1156,6 @@ static int fsl_esdhc_init(struct
> fsl_esdhc_priv *priv, if (ret)
>  		return ret;
>  
> -#ifdef CONFIG_MCF5441x
> -	/* ColdFire, using SDHC_DATA[3] for card detection */
> -	esdhc_write32(&regs->proctl, PROCTL_INIT | PROCTL_D3CD);
> -#endif
> -
>  #ifndef CONFIG_FSL_USDHC
>  	esdhc_setbits32(&regs->sysctl, SYSCTL_PEREN | SYSCTL_HCKEN
>  				| SYSCTL_IPGEN | SYSCTL_CKEN);
> @@ -1215,15 +1180,6 @@ static int fsl_esdhc_init(struct
> fsl_esdhc_priv *priv, voltage_caps = 0;
>  	caps = esdhc_read32(&regs->hostcapblt);
>  
> -#ifdef CONFIG_MCF5441x
> -	/*
> -	 * MCF5441x RM declares in more points that sdhc clock speed
> must
> -	 * never exceed 25 Mhz. From this, the HS bit needs to be
> disabled
> -	 * from host capabilities.
> -	 */
> -	caps &= ~ESDHC_HOSTCAPBLT_HSS;
> -#endif
> -
>  #ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC135
>  	caps = caps & ~(ESDHC_HOSTCAPBLT_SRS |
>  			ESDHC_HOSTCAPBLT_VS18 |
> ESDHC_HOSTCAPBLT_VS30); @@ -1375,45 +1331,6 @@ int
> fsl_esdhc_mmc_init(bd_t *bis) }
>  #endif
>  
> -#ifdef CONFIG_FSL_ESDHC_ADAPTER_IDENT
> -void mmc_adapter_card_type_ident(void)
> -{
> -	u8 card_id;
> -	u8 value;
> -
> -	card_id = QIXIS_READ(present) & QIXIS_SDID_MASK;
> -	gd->arch.sdhc_adapter = card_id;
> -
> -	switch (card_id) {
> -	case QIXIS_ESDHC_ADAPTER_TYPE_EMMC45:
> -		value = QIXIS_READ(brdcfg[5]);
> -		value |= (QIXIS_DAT4 | QIXIS_DAT5_6_7);
> -		QIXIS_WRITE(brdcfg[5], value);
> -		break;
> -	case QIXIS_ESDHC_ADAPTER_TYPE_SDMMC_LEGACY:
> -		value = QIXIS_READ(pwr_ctl[1]);
> -		value |= QIXIS_EVDD_BY_SDHC_VS;
> -		QIXIS_WRITE(pwr_ctl[1], value);
> -		break;
> -	case QIXIS_ESDHC_ADAPTER_TYPE_EMMC44:
> -		value = QIXIS_READ(brdcfg[5]);
> -		value |= (QIXIS_SDCLKIN | QIXIS_SDCLKOUT);
> -		QIXIS_WRITE(brdcfg[5], value);
> -		break;
> -	case QIXIS_ESDHC_ADAPTER_TYPE_RSV:
> -		break;
> -	case QIXIS_ESDHC_ADAPTER_TYPE_MMC:
> -		break;
> -	case QIXIS_ESDHC_ADAPTER_TYPE_SD:
> -		break;
> -	case QIXIS_ESDHC_NO_ADAPTER:
> -		break;
> -	default:
> -		break;
> -	}
> -}
> -#endif
> -
>  #ifdef CONFIG_OF_LIBFDT
>  __weak int esdhc_status_fixup(void *blob, const char *compat)
>  {
> @@ -1441,10 +1358,6 @@ void fdt_fixup_esdhc(void *blob, bd_t *bd)
>  	do_fixup_by_compat_u32(blob, compat, "clock-frequency",
>  			       gd->arch.sdhc_clk, 1);
>  #endif
> -#ifdef CONFIG_FSL_ESDHC_ADAPTER_IDENT
> -	do_fixup_by_compat_u32(blob, compat, "adapter-type",
> -			       (u32)(gd->arch.sdhc_adapter), 1);
> -#endif
>  }
>  #endif
>  
> @@ -1654,7 +1567,6 @@ static const struct udevice_id fsl_esdhc_ids[]
> = { { .compatible = "fsl,imx6q-usdhc", },
>  	{ .compatible = "fsl,imx7d-usdhc", .data =
> (ulong)&usdhc_imx7d_data,}, { .compatible = "fsl,imx7ulp-usdhc", },
> -	{ .compatible = "fsl,esdhc", },

Please keep the above line (as Peng mentioned) - it allows re-using
this driver on VF610 and i.MX53 devices.

>  	{ /* sentinel */ }
>  };
>  
> diff --git a/include/fsl_esdhc_imx.h b/include/fsl_esdhc_imx.h
> index e05b24e7e8..8abd28ea50 100644
> --- a/include/fsl_esdhc_imx.h
> +++ b/include/fsl_esdhc_imx.h
> @@ -17,10 +17,6 @@
>  /* needed for the mmc_cfg definition */
>  #include <mmc.h>
>  
> -#ifdef CONFIG_FSL_ESDHC_ADAPTER_IDENT
> -#include "../board/freescale/common/qixis.h"
> -#endif
> -
>  /* FSL eSDHC-specific constants */
>  #define SYSCTL			0x0002e02c
>  #define SYSCTL_INITA		0x08000000




Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190529/b69d339b/attachment.sig>