From: Ramon Fried <rfried.dev@gmail.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 5/6] net: macb: add dma_burst_length config
Date: Tue, 11 Jun 2019 18:19:29 +0300 [thread overview]
Message-ID: <20190611151930.15852-5-rfried.dev@gmail.com> (raw)
In-Reply-To: <20190611151930.15852-1-rfried.dev@gmail.com>
GEM support higher DMA burst writes/reads than the default (4).
add configuration structure with dma burst length so it could be
applied later to DMA configuration.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
---
drivers/net/macb.c | 22 +++++++++++++++++++++-
1 file changed, 21 insertions(+), 1 deletion(-)
diff --git a/drivers/net/macb.c b/drivers/net/macb.c
index ae8937bbb1..fb42172520 100644
--- a/drivers/net/macb.c
+++ b/drivers/net/macb.c
@@ -82,6 +82,7 @@ struct macb_dma_desc {
struct macb_device {
void *regs;
+ unsigned int dma_burst_length;
unsigned int rx_tail;
unsigned int tx_head;
@@ -118,6 +119,11 @@ struct macb_device {
phy_interface_t phy_interface;
#endif
};
+
+struct macb_config {
+ unsigned int dma_burst_length;
+};
+
#ifndef CONFIG_DM_ETH
#define to_macb(_nd) container_of(_nd, struct macb_device, netdev)
#endif
@@ -1133,8 +1139,13 @@ static int macb_enable_clk(struct udevice *dev)
}
#endif
+static const struct macb_config default_gem_config = {
+ .dma_burst_length = 16,
+};
+
static int macb_eth_probe(struct udevice *dev)
{
+ const struct macb_config *macb_config;
struct eth_pdata *pdata = dev_get_platdata(dev);
struct macb_device *macb = dev_get_priv(dev);
const char *phy_mode;
@@ -1151,6 +1162,11 @@ static int macb_eth_probe(struct udevice *dev)
macb->regs = (void *)pdata->iobase;
+ macb_config = (struct macb_config *)dev_get_driver_data(dev);
+ if (!macb_config)
+ macb_config = &default_gem_config;
+
+ macb->dma_burst_length = macb_config->dma_burst_length;
#ifdef CONFIG_CLK
ret = macb_enable_clk(dev);
if (ret)
@@ -1211,12 +1227,16 @@ static int macb_eth_ofdata_to_platdata(struct udevice *dev)
return macb_late_eth_ofdata_to_platdata(dev);
}
+static const struct macb_config sama5d4_config = {
+ .dma_burst_length = 4,
+};
+
static const struct udevice_id macb_eth_ids[] = {
{ .compatible = "cdns,macb" },
{ .compatible = "cdns,at91sam9260-macb" },
{ .compatible = "atmel,sama5d2-gem" },
{ .compatible = "atmel,sama5d3-gem" },
- { .compatible = "atmel,sama5d4-gem" },
+ { .compatible = "atmel,sama5d4-gem", .data = (ulong)&sama5d4_config },
{ .compatible = "cdns,zynq-gem" },
{ }
};
--
2.21.0
next prev parent reply other threads:[~2019-06-11 15:19 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-06-11 15:19 [U-Boot] [PATCH 1/6] net: macb: sync header definitions as taken from Linux Ramon Fried
2019-06-11 15:19 ` [U-Boot] [PATCH 2/6] net: macb: add support for faster clk rates Ramon Fried
2019-07-03 3:35 ` Anup Patel
2019-07-08 23:09 ` Joe Hershberger
2019-06-11 15:19 ` [U-Boot] [PATCH 3/6] net: macb: use bit access macro from header file Ramon Fried
2019-07-03 3:35 ` Anup Patel
2019-07-08 23:11 ` Joe Hershberger
2019-06-11 15:19 ` [U-Boot] [PATCH 4/6] net: macb: add support for SGMII phy interface Ramon Fried
2019-07-03 3:35 ` Anup Patel
2019-07-08 23:12 ` Joe Hershberger
2019-06-11 15:19 ` Ramon Fried [this message]
2019-07-03 3:35 ` [U-Boot] [PATCH 5/6] net: macb: add dma_burst_length config Anup Patel
2019-07-08 23:23 ` Joe Hershberger
2019-06-11 15:19 ` [U-Boot] [PATCH 6/6] net: macb: apply sane DMA configuration Ramon Fried
2019-07-03 3:36 ` Anup Patel
2019-07-08 23:26 ` Joe Hershberger
2019-07-03 3:35 ` [U-Boot] [PATCH 1/6] net: macb: sync header definitions as taken from Linux Anup Patel
2019-07-08 23:08 ` Joe Hershberger
2019-07-15 18:31 ` Joe Hershberger
2019-07-15 20:19 ` Ramon Fried
2019-07-15 20:25 ` Ramon Fried
2019-07-15 20:48 ` Joe Hershberger
2019-07-16 5:02 ` Ramon Fried
2019-07-16 18:42 ` Joe Hershberger
2019-07-16 18:54 ` Ramon Fried
-- strict thread matches above, loose matches on Subject: below --
2019-07-16 19:03 [U-Boot] [PATCH v2 " Ramon Fried
2019-07-16 19:03 ` [U-Boot] [PATCH 5/6] net: macb: add dma_burst_length config Ramon Fried
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190611151930.15852-5-rfried.dev@gmail.com \
--to=rfried.dev@gmail.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox