[U-Boot] [PATCH 1/2] ARM: omap3_logic: Enable OMAP EHCI support for SOM-LV Boards

[U-Boot] [PATCH 1/2] ARM: omap3_logic: Enable OMAP EHCI support for SOM-LV Boards

[Adam Ford]

The SOM-LV boards support the OMAP EHCI driver using port 2.
With the driver updated to support device tree, this patch sets
the corresponding pin muxing for the tranceiver as well as the
reset pin.

Signed-off-by: Adam Ford <aford173@gmail.com>

diff --git a/board/logicpd/omap3som/omap3logic.h b/board/logicpd/omap3som/omap3logic.h
index aeb26b90d7..63c2141783 100644
--- a/board/logicpd/omap3som/omap3logic.h
+++ b/board/logicpd/omap3som/omap3logic.h
@@ -161,12 +161,14 @@ void set_muxconf_regs(void)
 	MUX_VAL(CP(ETK_D7_ES2), (IEN  | PTD | DIS | M0)); /*ETK_D7*/
 	MUX_VAL(CP(ETK_D8_ES2), (IEN  | PTD | DIS | M0)); /*ETK_D8*/
 	MUX_VAL(CP(ETK_D9_ES2), (IEN  | PTD | DIS | M0)); /*ETK_D9*/
+#ifndef CONFIG_USB_EHCI_OMAP /* Torpedo does not use EHCI_OMAP */
 	MUX_VAL(CP(ETK_D10_ES2), (IEN  | PTD | DIS | M0)); /*ETK_D10*/
 	MUX_VAL(CP(ETK_D11_ES2), (IEN  | PTD | DIS | M0)); /*ETK_D11*/
 	MUX_VAL(CP(ETK_D12_ES2), (IEN  | PTD | DIS | M0)); /*ETK_D12*/
 	MUX_VAL(CP(ETK_D13_ES2), (IEN  | PTD | DIS | M0)); /*ETK_D13*/
 	MUX_VAL(CP(ETK_D14_ES2), (IEN  | PTD | DIS | M0)); /*ETK_D14*/
 	MUX_VAL(CP(ETK_D15_ES2), (IEN  | PTD | DIS | M0)); /*ETK_D15*/
+#endif
 
 	MUX_VAL(CP(D2D_MCAD1), (IEN  | PTD | EN  | M0)); /*d2d_mcad1*/
 	MUX_VAL(CP(D2D_MCAD2), (IEN  | PTD | EN  | M0)); /*d2d_mcad2*/
@@ -231,6 +233,23 @@ void set_muxconf_regs(void)
 	MUX_VAL(CP(D2D_SREAD),   (IEN  | PTD | DIS | M0)); /*d2d_sread*/
 	MUX_VAL(CP(D2D_MBUSFLAG), (IEN  | PTD | DIS | M0)); /*d2d_mbusflag*/
 	MUX_VAL(CP(D2D_SBUSFLAG), (IEN  | PTD | DIS | M0)); /*d2d_sbusflag*/
+
+#ifdef CONFIG_USB_EHCI_OMAP /* SOM-LV Uses EHCI-OMAP */
+	MUX_VAL(CP(ETK_D14_ES2),	(IEN  | PTD | DIS | M3));	/*HSUSB2_DATA0*/
+	MUX_VAL(CP(ETK_D15_ES2),	(IEN  | PTD | DIS | M3));	/*HSUSB2_DATA1*/
+	MUX_VAL(CP(MCSPI1_CS3),		(IEN  | PTD | EN  | M0));	/*HSUSB2_DATA2*/
+	MUX_VAL(CP(MCSPI2_CS1),		(IEN  | PTD | EN  | M0));	/*HSUSB2_DATA3*/
+	MUX_VAL(CP(MCSPI2_SIMO),	(IEN  | PTD | DIS | M0));	/*HSUSB2_DATA4*/
+	MUX_VAL(CP(MCSPI2_SOMI),	(IEN  | PTD | DIS | M0));	/*HSUSB2_DATA5*/
+	MUX_VAL(CP(MCSPI2_CS0),		(IEN  | PTD | EN  | M0));	/*HSUSB2_DATA6*/
+	MUX_VAL(CP(MCSPI2_CLK),		(IEN  | PTD | DIS | M0));	/*HSUSB2_DATA7*/
+	MUX_VAL(CP(SYS_BOOT2),      (IEN  | PTD | DIS | M4)) 	/* GPIO_4 */
+	MUX_VAL(CP(ETK_D10_ES2),	(IDIS | PTU | DIS | M3));	/*HSUSB2_CLK*/
+	MUX_VAL(CP(ETK_D11_ES2),	(IDIS | PTU | DIS | M3));	/*HSUSB2_STP*/
+	MUX_VAL(CP(ETK_D12_ES2),	(IEN  | PTU | DIS | M3));	/*HSUSB2_DIR*/
+	MUX_VAL(CP(ETK_D13_ES2),	(IEN  | PTD | DIS | M3));	/*HSUSB2_NXT*/
+#endif
+
 }
 
 #endif
diff --git a/include/configs/omap3_logic.h b/include/configs/omap3_logic.h
index e318a9f896..a5ae93914d 100644
--- a/include/configs/omap3_logic.h
+++ b/include/configs/omap3_logic.h
@@ -30,6 +30,10 @@
 /* I2C */
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM AT24C64      */
 
+#ifdef CONFIG_USB_EHCI_OMAP
+#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO	4
+#endif
+
 /* Board NAND Info. */
 #ifdef CONFIG_NAND
 #define CONFIG_SYS_MAX_NAND_DEVICE	1	  /* Max number of */
-- 
2.17.1

[U-Boot] [PATCH 2/2] ARM: omap3_logic & omap35_logic: Disable OMAP EHCI for Torpedo

[Adam Ford]

The OMAP35 and AM/DM37 Torpedo boards do not have a USB
tranceiver connected to the USB host port, so this patch
removes it from the defconfig files.

Signed-off-by: Adam Ford <aford173@gmail.com>

diff --git a/configs/omap35_logic_defconfig b/configs/omap35_logic_defconfig
index 3a529e8836..055a1bf489 100644
--- a/configs/omap35_logic_defconfig
+++ b/configs/omap35_logic_defconfig
@@ -69,6 +69,7 @@ CONFIG_USB=y
 CONFIG_DM_USB=y
 # CONFIG_SPL_DM_USB is not set
 CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_OMAP is not set
 CONFIG_USB_MUSB_HOST=y
 CONFIG_USB_MUSB_OMAP2PLUS=y
 CONFIG_TWL4030_USB=y
diff --git a/configs/omap3_logic_defconfig b/configs/omap3_logic_defconfig
index 0868e33131..b259b3720e 100644
--- a/configs/omap3_logic_defconfig
+++ b/configs/omap3_logic_defconfig
@@ -68,6 +68,7 @@ CONFIG_USB=y
 CONFIG_DM_USB=y
 # CONFIG_SPL_DM_USB is not set
 CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_OMAP is not set
 CONFIG_USB_MUSB_HOST=y
 CONFIG_USB_MUSB_OMAP2PLUS=y
 CONFIG_TWL4030_USB=y
-- 
2.17.1

[U-Boot] [PATCH 1/2] ARM: omap3_logic: Enable OMAP EHCI support for SOM-LV Boards

[Tom Rini]

On Sun, Jun 30, 2019 at 05:30:49PM -0500, Adam Ford wrote:

> The SOM-LV boards support the OMAP EHCI driver using port 2.
> With the driver updated to support device tree, this patch sets
> the corresponding pin muxing for the tranceiver as well as the
> reset pin.
> 
> Signed-off-by: Adam Ford <aford173@gmail.com>
> 
> diff --git a/board/logicpd/omap3som/omap3logic.h b/board/logicpd/omap3som/omap3logic.h
> index aeb26b90d7..63c2141783 100644

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190728/1013315b/attachment.sig>

[U-Boot] [PATCH 2/2] ARM: omap3_logic & omap35_logic: Disable OMAP EHCI for Torpedo

[Tom Rini]

On Sun, Jun 30, 2019 at 05:30:50PM -0500, Adam Ford wrote:

> The OMAP35 and AM/DM37 Torpedo boards do not have a USB
> tranceiver connected to the USB host port, so this patch
> removes it from the defconfig files.
> 
> Signed-off-by: Adam Ford <aford173@gmail.com>
> 
> diff --git a/configs/omap35_logic_defconfig b/configs/omap35_logic_defconfig
> index 3a529e8836..055a1bf489 100644

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190728/5381fc4d/attachment.sig>