From: Tom Rini <trini@konsulko.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH v3 01/16] arm: K3: j721e: Add basic support for J721E SoC definition
Date: Sun, 28 Jul 2019 17:47:00 -0400 [thread overview]
Message-ID: <20190728214700.GS20116@bill-the-cat> (raw)
In-Reply-To: <20190613045957.25133-2-lokeshvutla@ti.com>
On Thu, Jun 13, 2019 at 10:29:42AM +0530, Lokesh Vutla wrote:
> The J721E SoC belongs to the K3 Multicore SoC architecture platform,
> providing advanced system integration to enable lower system costs
> of automotive applications such as infotainment, cluster, premium
> Audio, Gateway, industrial and a range of broad market applications.
> This SoC is designed around reducing the system cost by eliminating
> the need of an external system MCU and is targeted towards ASIL-B/C
> certification/requirements in addition to allowing complex software
> and system use-cases.
>
> Some highlights of this SoC are:
> * Dual Cortex-A72s in a single cluster, three clusters of lockstep
> capable dual Cortex-R5F MCUs, Deep-learning Matrix Multiply Accelerator(MMA),
> C7x floating point Vector DSP, Two C66x floating point DSPs.
> * 3D GPU PowerVR Rogue 8XE GE8430
> * Vision Processing Accelerator (VPAC) with image signal processor and Depth
> and Motion Processing Accelerator (DMPAC)
> * Two Gigabit Industrial Communication Subsystems (ICSSG), each with dual
> PRUs and dual RTUs
> * Two CSI2.0 4L RX plus one CSI2.0 4L TX, one eDP/DP, One DSI Tx, and
> up to two DPI interfaces.
> * Integrated Ethernet switch supporting up to a total of 8 external ports in
> addition to legacy Ethernet switch of up to 2 ports.
> * System MMU (SMMU) Version 3.0 and advanced virtualisation
> capabilities.
> * Upto 4 PCIe-GEN3 controllers, 2 USB3.0 Dual-role device subsystems,
> 16 MCANs, 12 McASP, eMMC and SD, UFS, OSPI/HyperBus memory controller, QSPI,
> I3C and I2C, eCAP/eQEP, eHRPWM, MLB among other peripherals.
> * Two hardware accelerator block containing AES/DES/SHA/MD5 called SA2UL
> management.
> * Configurable L3 Cache and IO-coherent architecture with high data throughput
> capable distributed DMA architecture under NAVSS
> * Centralized System Controller for Security, Power, and Resource
> Management (DMSC)
>
> See J721E Technical Reference Manual (SPRUIL1, May 2019)
> for further details: http://www.ti.com/lit/pdf/spruil1
>
> Add base support for J721E SoC
>
> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
> Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
> Signed-off-by: Nishanth Menon <nm@ti.com>
Applied to u-boot/master, thanks!
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190728/e23a3b2b/attachment.sig>
next prev parent reply other threads:[~2019-07-28 21:47 UTC|newest]
Thread overview: 34+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-06-13 4:59 [U-Boot] [PATCH v3 00/16] arm: k3: arm64: Initial support for Texas Instrument's J721E Platform Lokesh Vutla
2019-06-13 4:59 ` [U-Boot] [PATCH v3 01/16] arm: K3: j721e: Add basic support for J721E SoC definition Lokesh Vutla
2019-07-28 21:47 ` Tom Rini [this message]
2019-06-13 4:59 ` [U-Boot] [PATCH v3 02/16] armv7R: K3: j721e: Add support for boot device detection Lokesh Vutla
2019-07-28 21:47 ` Tom Rini
2019-06-13 4:59 ` [U-Boot] [PATCH v3 03/16] armv7R: K3: j721e: Unlock all applicable control MMR registers Lokesh Vutla
2019-07-28 21:47 ` Tom Rini
2019-06-13 4:59 ` [U-Boot] [PATCH v3 04/16] armv7R: K3: j721e: Store boot index from ROM Lokesh Vutla
2019-07-28 21:47 ` Tom Rini
2019-07-28 21:47 ` Tom Rini
2019-06-13 4:59 ` [U-Boot] [PATCH v3 05/16] armv7R: K3: j721e: Shut down R5 core after ATF startup on A72 Lokesh Vutla
2019-07-28 21:47 ` Tom Rini
2019-06-13 4:59 ` [U-Boot] [PATCH v3 06/16] armv7R: K3: j721e: Load SYSFW binary and config from boot media Lokesh Vutla
2019-07-28 21:47 ` Tom Rini
2019-06-13 4:59 ` [U-Boot] [PATCH v3 07/16] armv8: K3: j721e: Add custom MMU support Lokesh Vutla
2019-07-28 21:47 ` Tom Rini
2019-06-13 4:59 ` [U-Boot] [PATCH v3 08/16] board: ti: j721e: Add board support for j721e evm Lokesh Vutla
2019-07-28 21:47 ` Tom Rini
2019-06-13 4:59 ` [U-Boot] [PATCH v3 09/16] board: ti: j721e: Enable fixing up msmc sram node Lokesh Vutla
2019-07-28 21:47 ` Tom Rini
2019-06-13 4:59 ` [U-Boot] [PATCH v3 10/16] mmc: am654_sdhci: Separate J721E compatible into 8bit and 4bit versions Lokesh Vutla
2019-07-28 21:47 ` Tom Rini
2019-06-13 4:59 ` [U-Boot] [PATCH v3 11/16] dt-bindings: pinctrl: k3: Introduce pinmux definitions for J721E Lokesh Vutla
2019-07-28 21:48 ` Tom Rini
2019-06-13 4:59 ` [U-Boot] [PATCH v3 12/16] arm: dts: ti: Add Support for J721E SoC Lokesh Vutla
2019-07-28 21:48 ` Tom Rini
2019-06-13 4:59 ` [U-Boot] [PATCH v3 13/16] arm: dts: k3-j721e: Add initial support for common processor board Lokesh Vutla
2019-07-28 21:48 ` Tom Rini
2019-06-13 4:59 ` [U-Boot] [PATCH v3 14/16] arm: dts: k3-j721e: Add r5 specific dt support Lokesh Vutla
2019-07-28 21:48 ` Tom Rini
2019-06-13 4:59 ` [U-Boot] [PATCH v3 15/16] configs: j721e_evm_r5: Add initial support Lokesh Vutla
2019-07-28 21:48 ` Tom Rini
2019-06-13 4:59 ` [U-Boot] [PATCH v3 16/16] configs: j721e_evm_a72: " Lokesh Vutla
2019-07-28 21:48 ` Tom Rini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190728214700.GS20116@bill-the-cat \
--to=trini@konsulko.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox