[RESEND PATCH v1] colibri_imx6: fix broken fsl_esdhc_imx conversion

[Tom Rini <trini@konsulko.com>]

On Mon, Dec 09, 2019 at 03:03:48PM +0000, Oliver Graute wrote:
> On 06/12/19, Tom Rini wrote:
> > On Fri, Dec 06, 2019 at 06:23:09PM +0100, Lukasz Majewski wrote:
> > > Hi Igor,
> > > 
> > > > Hi Stefano
> > > > 
> > > > On Fri, Dec 6, 2019 at 6:24 PM Igor Opaniuk <igor.opaniuk@gmail.com>
> > > > wrote:
> > > > >
> > > > > From: Igor Opaniuk <igor.opaniuk@toradex.com>
> > > > >
> > > > > Not all CONFIG_FSL_ESDHC defines were properly replaced with
> > > > > CONFIG_FSL_ESDHC_IMX, which broke U-boot proper booting on
> > > > > Colibri iMX6 SoMs.
> > > > >
> > > > > U-boot is stuck after this message:
> > > > > Commercial temperature grade DDR3 timings, 64bit bus width.
> > > > > Trying to boot from MMC1
> > > > >
> > > > > Fixes: e37ac717d7("Convert to use fsl_esdhc_imx for i.MX platforms")
> > > > > Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
> > > > > ---
> > > > >
> > > > >  board/toradex/colibri_imx6/colibri_imx6.c | 4 ++--
> > > > >  1 file changed, 2 insertions(+), 2 deletions(-)
> > > > >
> > > > > diff --git a/board/toradex/colibri_imx6/colibri_imx6.c
> > > > > b/board/toradex/colibri_imx6/colibri_imx6.c index
> > > > > ad40b589c1..44173dde1f 100644 ---
> > > > > a/board/toradex/colibri_imx6/colibri_imx6.c +++
> > > > > b/board/toradex/colibri_imx6/colibri_imx6.c @@ -83,7 +83,7 @@
> > > > > iomux_v3_cfg_t const uart1_pads[] = {
> > > > > MX6_PAD_CSI0_DAT11__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), };
> > > > >
> > > > > -#if defined(CONFIG_FSL_ESDHC) && defined(CONFIG_SPL_BUILD)
> > > > > +#if defined(CONFIG_FSL_ESDHC_IMX) && defined(CONFIG_SPL_BUILD)
> > > > >  /* Colibri MMC */
> > > > >  iomux_v3_cfg_t const usdhc1_pads[] = {
> > > > >         MX6_PAD_SD1_CLK__SD1_CLK    | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> > > > > @@ -304,7 +304,7 @@ int board_ehci_hcd_init(int port)
> > > > >  }
> > > > >  #endif
> > > > >
> > > > > -#if defined(CONFIG_FSL_ESDHC) && defined(CONFIG_SPL_BUILD)
> > > > > +#if defined(CONFIG_FSL_ESDHC_IMX) && defined(CONFIG_SPL_BUILD)
> > > > >  /* use the following sequence: eMMC, MMC */
> > > > >  struct fsl_esdhc_cfg usdhc_cfg[CONFIG_SYS_FSL_USDHC_NUM] = {
> > > > >         {USDHC3_BASE_ADDR},
> > > > > --
> > > > > 2.17.1
> > > > >  
> > > > 
> > > > I've just found the same fix [1] but from Ricardo with Awaiting
> > > > upstream status in patchwork (I thought that he has fixed just Apalis
> > > > iMX6), but seems the patch was
> > > > lost somewhere, as I can not find it nor in u-boot-imx/next neither
> > > > in u-boot-imx/master branches.
> > > 
> > > Thanks for providing the fix (at least for the Toradex boards)
> > > 
> > > And I do guess that more i.MX6 boards are affected ...
> > 
> > I think there's just one other.  The imx8qm_rom7720_a1 references
> > CONFIG_FSL_ESDHC still, but I don't see any other i.MX8 platforms doing
> > anything with the symbol to compare with.
> 
> thx for that hint, so I must replace CONFIG_FSL_ESDHC with
> CONFIG_FSL_ESDHC_IMX in board/advantech/imx8qm_rom7720_a1/spl.c ?

Yes, and confirm that everything works as expected for the appropriate
use cases.  Thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 833 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20191209/1965ff24/attachment.sig>