[U-Boot] [PATCH 2/4] imx: cx9020: migrate cx9020 to CONFIG_DM_USB

[U-Boot] [PATCH 2/4] imx: cx9020: migrate cx9020 to CONFIG_DM_USB

[linux-kernel-dev at beckhoff.com]

From: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>

Note: gpio7_8 was never used for usb power regulator so we remove it here

Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
---

 arch/arm/dts/imx53-cx9020.dts          | 11 ++++++++++-
 board/beckhoff/mx53cx9020/mx53cx9020.c | 10 ----------
 configs/mx53cx9020_defconfig           |  6 ++++++
 3 files changed, 16 insertions(+), 11 deletions(-)

diff --git a/arch/arm/dts/imx53-cx9020.dts b/arch/arm/dts/imx53-cx9020.dts
index 2b7f7288088..e08850999b1 100644
--- a/arch/arm/dts/imx53-cx9020.dts
+++ b/arch/arm/dts/imx53-cx9020.dts
@@ -36,7 +36,6 @@
 				MX53_PAD_GPIO_1__GPIO1_1          0x80000000
 				MX53_PAD_GPIO_4__GPIO1_4          0x80000000
 				MX53_PAD_PATA_DA_0__GPIO7_6       0x80000000
-				MX53_PAD_PATA_DA_2__GPIO7_8	  0x80000000
 				MX53_PAD_GPIO_16__GPIO7_11        0x80000000
 
 				MX53_PAD_EIM_OE__EMI_WEIM_OE            0x80000000
@@ -220,3 +219,13 @@
 		full-duplex;
 	};
 };
+
+&usbh1 {
+	phy_type = "utmi";
+	status = "okay";
+};
+
+&usbotg {
+	dr_mode = "host";
+	status = "okay";
+};
diff --git a/board/beckhoff/mx53cx9020/mx53cx9020.c b/board/beckhoff/mx53cx9020/mx53cx9020.c
index 9450d925f6f..caffd5c9ee8 100644
--- a/board/beckhoff/mx53cx9020/mx53cx9020.c
+++ b/board/beckhoff/mx53cx9020/mx53cx9020.c
@@ -127,16 +127,6 @@ static void setup_gpio_leds(void)
 	gpio_direction_output(GPIO_LED_PWR_G, 0);
 }
 
-#ifdef CONFIG_USB_EHCI_MX5
-int board_ehci_hcd_init(int port)
-{
-	/* request VBUS power enable pin, GPIO7_8 */
-	gpio_direction_output(IMX_GPIO_NR(7, 8), 1);
-	return 0;
-}
-#endif
-
-
 static int power_init(void)
 {
 	/* nothing to do on CX9020 */
diff --git a/configs/mx53cx9020_defconfig b/configs/mx53cx9020_defconfig
index 17c44bd070a..6087ed81ec9 100644
--- a/configs/mx53cx9020_defconfig
+++ b/configs/mx53cx9020_defconfig
@@ -19,7 +19,13 @@ CONFIG_CMD_PXE=y
 CONFIG_CMD_EXT2=y
 CONFIG_CMD_EXT4=y
 CONFIG_CMD_FAT=y
+CONFIG_CMD_USB=y
 CONFIG_CMD_FS_GENERIC=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_MX5=y
+CONFIG_USB_STORAGE=y
+CONFIG_DM_REGULATOR=y
 CONFIG_OF_CONTROL=y
 CONFIG_DEFAULT_DEVICE_TREE="imx53-cx9020"
 CONFIG_ENV_IS_IN_MMC=y
-- 
2.23.0

[U-Boot] [PATCH 2/4] imx: cx9020: migrate cx9020 to CONFIG_DM_USB

[sbabic at denx.de]

> From: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
> Note: gpio7_8 was never used for usb power regulator so we remove it here
> Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com>
> Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Applied to u-boot-imx, -next, thanks !

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================