[PATCH 13/13] Nokia RX-51: Enable usbtty serial console by default

["Pali Rohár" <pali@kernel.org>]

Now when usbtty serial console is fixed in U-Boot enable it for Nokia RX-51
board by default.

CONFIG_CONSOLE_MUX is already used and U-Boot console is available for
all in/out devices. Therefore there is no need to have separate commands
'run sercon', 'run usbcon' and 'run vgacon', so remove them.

As space for U-Boot is limited to 256kB, disable some other unused options
so CONFIG_USB_TTY can be enabled.

Nokia RX-51 does not have easily accessible UART serial console so the only
option for easy debugging is to use device's keyboard+screen or this usbtty
serial console over USB.

Signed-off-by: Pali Roh?r <pali@kernel.org>
---
 configs/nokia_rx51_defconfig |  6 +++---
 doc/README.nokia_rx51        | 15 +--------------
 include/configs/nokia_rx51.h | 16 ++++------------
 3 files changed, 8 insertions(+), 29 deletions(-)

diff --git a/configs/nokia_rx51_defconfig b/configs/nokia_rx51_defconfig
index 0f05fe6fc3..e1b874a870 100644
--- a/configs/nokia_rx51_defconfig
+++ b/configs/nokia_rx51_defconfig
@@ -44,18 +44,16 @@ CONFIG_MTDPARTS_DEFAULT="mtdparts=onenand:128k(bootloader)ro,384k(config),256k(l
 CONFIG_ENV_OVERWRITE=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 # CONFIG_NET is not set
-CONFIG_TWL4030_LED=y
 # CONFIG_MMC_HW_PARTITIONING is not set
+# CONFIG_MMC_VERBOSE is not set
 CONFIG_MMC_OMAP_HS=y
 CONFIG_MTD=y
 CONFIG_CONS_INDEX=3
 CONFIG_SYS_NS16550=y
 CONFIG_SPI=y
 CONFIG_USB=y
-CONFIG_USB_MUSB_HCD=y
 CONFIG_USB_MUSB_UDC=y
 CONFIG_USB_OMAP3=y
-CONFIG_TWL4030_USB=y
 CONFIG_CFB_CONSOLE=y
 CONFIG_CFB_CONSOLE_ANSI=y
 # CONFIG_VGA_AS_SINGLE_DEVICE is not set
@@ -66,3 +64,5 @@ CONFIG_DM_I2C=y
 CONFIG_DM_MMC=y
 # CONFIG_DM_DEVICE_REMOVE is not set
 # CONFIG_SYS_MALLOC_F is not set
+# CONFIG_DM_WARN is not set
+# CONFIG_BLOCK_CACHE is not set
diff --git a/doc/README.nokia_rx51 b/doc/README.nokia_rx51
index 320b5efc7d..84d1912ddd 100644
--- a/doc/README.nokia_rx51
+++ b/doc/README.nokia_rx51
@@ -24,8 +24,7 @@ called u-boot-gen-combined. It is available in following repository:
 There is support for hardware watchdog. Hardware watchdog is started by
 NOLO so u-boot must kick watchdog to prevent reboot device (but not very
 often, max every 2 seconds). There is also support for framebuffer display
-output with ANSI escape codes and the N900 HW keyboard input. USB tty works
-but is disabled because it prevents the current Maemo kernel from booting.
+output with ANSI escape codes and the N900 HW keyboard input.
 
 When U-Boot is starting it enable IBE bit in Auxiliary Control Register,
 which is needed for Thumb-2 ISA support. It is workaround for errata 430973.
@@ -49,10 +48,6 @@ Boot from SD or eMMC in this order:
 
 Available additional commands/variables:
 
- * run sercon - Use serial port for control
- * run usbcon - Use usbtty for control
- * run vgacon - Use framebuffer and HW keyboard for control (default)
-
  * run sdboot - Boot from external SD card (see boot order)
  * run emmcboot - Boot from internal eMMC memory (see boot order)
  * run attachboot - Boot attached kernel image (attached to U-Boot binary)
@@ -87,14 +82,6 @@ Additional variables for booting kernel:
  and u-boot standard output is set to serial then setup_console_atag is
  automatically set to 1. So output from Maemo kernel would go to serial port.
 
-USB TTY:
-
- Maemo kernel 2.6.28 will crash if u-boot enable usb tty. So USB TTY is disabled.
- For enabling USB TTY just add this line to file include/configs/nokia_rx51.h
-
- #define CONFIG_USB_TTY
-
-
 UBIFS support:
 
  UBIFS support is disabled, because U-Boot image is too big and cannot be
diff --git a/include/configs/nokia_rx51.h b/include/configs/nokia_rx51.h
index 6879f52a0c..36b1f9221c 100644
--- a/include/configs/nokia_rx51.h
+++ b/include/configs/nokia_rx51.h
@@ -70,6 +70,7 @@
 
 /* USB device configuration */
 #define CONFIG_USB_DEVICE
+#define CONFIG_USB_TTY
 #define CONFIG_USBD_VENDORID		0x0421
 #define CONFIG_USBD_PRODUCTID		0x01c8
 #define CONFIG_USBD_MANUFACTURER	"Nokia"
@@ -108,15 +109,9 @@ int rx51_kp_getc(struct stdio_dev *sdev);
 /* Environment information */
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"usbtty=cdc_acm\0" \
-	"stdin=serial,vga\0" \
-	"stdout=serial,vga\0" \
-	"stderr=serial,vga\0" \
-	"setcon=setenv stdin ${con};" \
-		"setenv stdout ${con};" \
-		"setenv stderr ${con}\0" \
-	"sercon=setenv con serial; run setcon\0" \
-	"usbcon=setenv con usbtty; run setcon\0" \
-	"vgacon=setenv con vga; run setcon\0" \
+	"stdin=usbtty,serial,vga\0" \
+	"stdout=usbtty,serial,vga\0" \
+	"stderr=usbtty,serial,vga\0" \
 	"slide=gpio input " __stringify(GPIO_SLIDE) "\0" \
 	"switchmmc=mmc dev ${mmcnum}\0" \
 	"kernaddr=0x82008000\0" \
@@ -209,9 +204,6 @@ int rx51_kp_getc(struct stdio_dev *sdev);
 #define CONFIG_POSTBOOTMENU \
 	"echo;" \
 	"echo Extra commands:;" \
-	"echo run sercon - Use serial port for control.;" \
-	"echo run usbcon - Use usbtty for control.;" \
-	"echo run vgacon - Use framebuffer/keyboard.;" \
 	"echo run sdboot - Boot from SD card slot.;" \
 	"echo run emmcboot - Boot internal eMMC memory.;" \
 	"echo run attachboot - Boot attached kernel image.;" \
-- 
2.20.1