From: Eugen Hristev <eugen.hristev@microchip.com>
To: u-boot@lists.denx.de
Subject: [PATCH 27/34] ARM: dts: at91: sama7g5ek: enable sdmmc0 with pinctrl
Date: Thu, 3 Dec 2020 11:28:43 +0200 [thread overview]
Message-ID: <20201203092850.7909-28-eugen.hristev@microchip.com> (raw)
In-Reply-To: <20201203092850.7909-1-eugen.hristev@microchip.com>
Enable sdmmc0 on this board. A non-removable eMMC is connected on this
block.
Configure pincontrol accordingly.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
---
arch/arm/dts/sama7g5ek.dts | 30 ++++++++++++++++++++++++++++++
1 file changed, 30 insertions(+)
diff --git a/arch/arm/dts/sama7g5ek.dts b/arch/arm/dts/sama7g5ek.dts
index 3eac94896d..452bf425df 100644
--- a/arch/arm/dts/sama7g5ek.dts
+++ b/arch/arm/dts/sama7g5ek.dts
@@ -36,6 +36,15 @@
ahb {
apb {
+ sdmmc0: sdio-host at e1204000 {
+ bus-width = <8>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdmmc0_cmd_data_default
+ &pinctrl_sdmmc0_ck_rstn_ds_cd_default>;
+ status = "okay";
+ };
+
sdmmc1: sdio-host at e1208000 {
bus-width = <4>;
pinctrl-names = "default";
@@ -86,6 +95,27 @@
bias-disable;
};
+ pinctrl_sdmmc0_cmd_data_default: sdmmc0_cmd_data_default {
+ pinmux = <PIN_PA1__SDMMC0_CMD>,
+ <PIN_PA3__SDMMC0_DAT0>,
+ <PIN_PA4__SDMMC0_DAT1>,
+ <PIN_PA5__SDMMC0_DAT2>,
+ <PIN_PA6__SDMMC0_DAT3>,
+ <PIN_PA7__SDMMC0_DAT4>,
+ <PIN_PA8__SDMMC0_DAT5>,
+ <PIN_PA9__SDMMC0_DAT6>,
+ <PIN_PA10__SDMMC0_DAT7>;
+ bias-pull-up;
+ };
+
+ pinctrl_sdmmc0_ck_rstn_ds_cd_default: sdmmc0_ck_rstn_ds_cd_default {
+ pinmux = <PIN_PA0__SDMMC0_CK>,
+ <PIN_PA2__SDMMC0_RSTN>,
+ <PIN_PA11__SDMMC0_DS>,
+ <PIN_PA14__SDMMC0_CD>;
+ bias-pull-up;
+ };
+
pinctrl_sdmmc1_cmd_data_default: sdmmc1_cmd_data_default {
pinmux = <PIN_PB29__SDMMC1_CMD>,
<PIN_PB31__SDMMC1_DAT0>,
--
2.25.1
next prev parent reply other threads:[~2020-12-03 9:28 UTC|newest]
Thread overview: 42+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-12-03 9:28 [PATCH 00/34] Sama7g5 Evaluation Kit support Eugen Hristev
2020-12-03 9:28 ` [PATCH 01/34] ARM: dts: sama7g5: add initial DT for sama7g5 SoC Eugen Hristev
2020-12-03 9:28 ` [PATCH 02/34] board: atmel: sama7g5ek: add initial support for sama7g5ek Eugen Hristev
2020-12-03 9:28 ` [PATCH 03/34] board: atmel: sama7g5ek: add SYS_MALLOC_F_LEN to SYS_INIT_SP_ADDR Eugen Hristev
2020-12-03 9:28 ` [PATCH 04/34] configs: sama7g5ek: set malloc pool to 68K Eugen Hristev
2020-12-03 9:28 ` [PATCH 05/34] configs: sama7g5ek: enable pll driver Eugen Hristev
2020-12-03 9:28 ` [PATCH 06/34] ARM: dts: sama7g5: move clock frequencies for xtals in board file Eugen Hristev
2020-12-03 9:28 ` [PATCH 07/34] ARM: dts: sama7g5: add slow rc and main rc oscillators Eugen Hristev
2020-12-03 9:28 ` [PATCH 08/34] ARM: dts: sama7g5: add u-boot, dm-pre-reloc bindings for xtals Eugen Hristev
2020-12-03 9:28 ` [PATCH 09/34] ARM: dts: sama7g5: add slow clock bindings Eugen Hristev
2020-12-03 9:28 ` [PATCH 10/34] ARM: dts: sama7g5: add PMC bindings Eugen Hristev
2020-12-03 9:28 ` [PATCH 11/34] ARM: dts: sama7g5: switch to " Eugen Hristev
2020-12-03 9:28 ` [PATCH 12/34] configs: sama7g5: enable CONFIG_CPU Eugen Hristev
2020-12-03 9:28 ` [PATCH 13/34] ARM: dts: sama7g5: add CPU bindings Eugen Hristev
2020-12-03 9:28 ` [PATCH 14/34] configs: sama7g5: use PIT64B Eugen Hristev
2020-12-03 9:28 ` [PATCH 15/34] ARM: dts: sama7g5: enable autoboot Eugen Hristev
2020-12-03 9:28 ` [PATCH 16/34] ARM: dts: sama7g5: add pit64b support Eugen Hristev
2020-12-03 9:28 ` [PATCH 17/34] ARM: dts: at91: sama7g5: add pinctrl node Eugen Hristev
2020-12-03 9:28 ` [PATCH 18/34] ARM: dts: at91: sama7g5ek: add pinctrl for sdmmc1 and flx3 Eugen Hristev
2020-12-03 9:28 ` [PATCH 19/34] configs: sama7g5ek: enable mii command Eugen Hristev
2020-12-03 9:28 ` [PATCH 20/34] ARM: dts: sama7g5: add GMAC0 Eugen Hristev
2020-12-03 9:28 ` [PATCH 21/34] ARM: dts: sama7g5: add GMAC1 Eugen Hristev
2020-12-03 9:28 ` [PATCH 22/34] board: atmel: sama7g5ek: increase arp timeout and retry count Eugen Hristev
2020-12-03 9:28 ` [PATCH 23/34] configs: sama7g5ek: enable support for KSZ9131 Eugen Hristev
2020-12-03 9:28 ` [PATCH 24/34] configs: sama7g5ek: enable CCF Eugen Hristev
2020-12-03 9:28 ` [PATCH 25/34] ARM: dts: at91: sama7g5: add assigned clocks for sdmmc1 Eugen Hristev
2020-12-03 9:28 ` [PATCH 26/34] ARM: dts: at91: sama7g5: add node for sdmmc0 Eugen Hristev
2020-12-03 9:28 ` Eugen Hristev [this message]
2020-12-03 9:28 ` [PATCH 28/34] board: atmel: sama7g5ek: clean-up header bootcommand Eugen Hristev
2020-12-03 9:28 ` [PATCH 29/34] configs: sama7g5: add mmc config for sdmmc0 Eugen Hristev
2020-12-03 10:38 ` Jaehoon Chung
2020-12-03 10:47 ` Eugen.Hristev at microchip.com
2020-12-03 11:11 ` Jaehoon Chung
2020-12-03 11:20 ` Eugen.Hristev at microchip.com
2020-12-03 21:45 ` Jaehoon Chung
2020-12-04 7:00 ` Eugen.Hristev at microchip.com
2020-12-06 22:15 ` Jaehoon Chung
2020-12-03 9:28 ` [PATCH 30/34] ARM: dts: at91: sama7g5: add flexcom1 and i2c subnode Eugen Hristev
2020-12-03 9:28 ` [PATCH 31/34] ARM: dts: sama7g5ek: add i2c1 bus and eeproms Eugen Hristev
2020-12-03 9:28 ` [PATCH 32/34] board: atmel: sama7g5ek: add support for MAC address retreival Eugen Hristev
2020-12-03 9:28 ` [PATCH 33/34] configs: sama7g5ek: add i2c and eeprom Eugen Hristev
2020-12-03 9:28 ` [PATCH 34/34] ARM: dts: sama7g5ek: fix TXC pin configuration Eugen Hristev
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201203092850.7909-28-eugen.hristev@microchip.com \
--to=eugen.hristev@microchip.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox