[PATCH 3/4] usb: musb: Fix handling interrupts for EP0 and SET ADDRESS commmand

[Lukasz Majewski <lukma@denx.de>]

Hi Pali,

> Interrupt for EP0 is indicated in intrtx register via first bit. It
> is set for both RX and TX. First bit in intrrx register is reserved
> and not set.
> 
> So remove calling musb_peri_ep0() function at every iteration of
> udc_irq() and musb_peri_rx() and call it only from musb_peri_tx()
> when correct interrupt bit in initrtx it set.
> 
> Address from SET ADDRESS command must be set to faddr register only
> after acknowledging SERV_RXPKTRDY followed by received EP0 interrupt.
> So prior calling musb_peri_ep0_set_address() check for EP0 interrupt
> instead of (incorrect) MUSB_INTR_SOF interrupt.
> 
> This patch fixes issue that host (computer) cannot register U-Boot USB
> device and failing with errors:
> 
>     usb 1-1: new full-speed USB device number 86 using xhci_hcd
>     usb 1-1: Device not responding to setup address.
>     usb 1-1: Device not responding to setup address.
>     usb 1-1: device not accepting address 86, error -71
> 
> U-Boot was writing address to faddr register too early and did not
> wait for correct interrupt after which should update address.
> 
> Signed-off-by: Pali Roh?r <pali@kernel.org>
> ---
>  drivers/usb/musb/musb_udc.c | 12 ++++--------
>  1 file changed, 4 insertions(+), 8 deletions(-)
> 
> diff --git a/drivers/usb/musb/musb_udc.c b/drivers/usb/musb/musb_udc.c
> index 7c74422623..50d8bc319c 100644
> --- a/drivers/usb/musb/musb_udc.c
> +++ b/drivers/usb/musb/musb_udc.c
> @@ -707,9 +707,7 @@ static void musb_peri_rx(u16 intr)
>  {
>  	unsigned int ep;
>  
> -	/* Check for EP0 */
> -	if (0x01 & intr)
> -		musb_peri_ep0();
> +	/* First bit is reserved and does not indicate interrupt for
> EP0 */ 
>  	for (ep = 1; ep < 16; ep++) {
>  		if ((1 << ep) & intr)
> @@ -721,9 +719,9 @@ static void musb_peri_tx(u16 intr)
>  {
>  	unsigned int ep;
>  
> -	/* Check for EP0 */
> +	/* Check for EP0: first bit indicates interrupt for both RX
> and TX */ if (0x01 & intr)
> -		musb_peri_ep0_tx();
> +		musb_peri_ep0();
>  
>  	for (ep = 1; ep < 16; ep++) {
>  		if ((1 << ep) & intr)
> @@ -750,8 +748,6 @@ void udc_irq(void)
>  			musb_peri_resume();
>  		}
>  
> -		musb_peri_ep0();
> -
>  		if (MUSB_INTR_RESET & intrusb) {
>  			usbd_device_event_irq(udc_device,
> DEVICE_RESET, 0); musb_peri_reset();
> @@ -790,7 +786,7 @@ void udc_irq(void)
>  			if (intrtx)
>  				musb_peri_tx(intrtx);
>  		} else {
> -			if (MUSB_INTR_SOF & intrusb) {
> +			if (readw(&musbr->intrtx) & 0x1) {
>  				u8 faddr;
>  				faddr = readb(&musbr->faddr);
>  				/*

Applying this patch causes error. Could you rebase your work on newest
master (after onging PR is accepted).

Thanks in advance and sorry for delay.


Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20210123/7bae5f10/attachment.sig>