From: Andre Przywara <andre.przywara@arm.com>
To: u-boot@lists.denx.de
Subject: [PATCH v2 2/4] usb: xhci-pci: Move reset logic out of XHCI core
Date: Wed, 21 Apr 2021 11:36:38 +0100 [thread overview]
Message-ID: <20210421113638.47770202@slackpad.fritz.box> (raw)
In-Reply-To: <20210417142059.45337-3-samuel@sholland.org>
On Sat, 17 Apr 2021 09:20:57 -0500
Samuel Holland <samuel@sholland.org> wrote:
Hi,
> Resetting an XHCI controller inside xhci_register undoes any register
> setup performed by the platform driver. And at least on the Allwinner
> H6, resetting the XHCI controller also resets the PHY, which prevents
> the controller from working. That means the controller must be taken out
> of reset before initializing the PHY, which must be done before calling
> xhci_register.
>
> The logic in the XHCI core was added to support the Raspberry Pi 4
> (although this was not mentioned in the commit log!), which uses the
> xhci-pci platform driver. Move the reset logic to the platform driver,
> where it belongs, and where it cannot interfere with other platform
> drivers.
>
> This also fixes a failure to call reset_free if xhci_register failed.
>
> Fixes: 0b80371b350e ("usb: xhci: Add reset controller support")
> Signed-off-by: Samuel Holland <samuel@sholland.org>
From my research it looks like no other board should be affected by the
change, and they have been no reports from the people I asked a few
weeks ago.
I'd say we should merge it, to expose it to a wider audience, and keep
an eye on bug reports.
Acked-by: Andre Przywara <andre.przywara@arm.com>
Cheers,
Andre
> ---
> drivers/usb/host/xhci-mem.c | 2 --
> drivers/usb/host/xhci-pci.c | 51 ++++++++++++++++++++++++++++++++++---
> drivers/usb/host/xhci.c | 35 -------------------------
> include/usb/xhci.h | 2 --
> 4 files changed, 47 insertions(+), 43 deletions(-)
>
> diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c
> index 1c11c2e7e0..0d9da62bab 100644
> --- a/drivers/usb/host/xhci-mem.c
> +++ b/drivers/usb/host/xhci-mem.c
> @@ -180,8 +180,6 @@ void xhci_cleanup(struct xhci_ctrl *ctrl)
> xhci_free_virt_devices(ctrl);
> free(ctrl->erst.entries);
> free(ctrl->dcbaa);
> - if (reset_valid(&ctrl->reset))
> - reset_free(&ctrl->reset);
> memset(ctrl, '\0', sizeof(struct xhci_ctrl));
> }
>
> diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c
> index aaa243f291..ea8e8f3211 100644
> --- a/drivers/usb/host/xhci-pci.c
> +++ b/drivers/usb/host/xhci-pci.c
> @@ -10,9 +10,14 @@
> #include <init.h>
> #include <log.h>
> #include <pci.h>
> +#include <reset.h>
> #include <usb.h>
> #include <usb/xhci.h>
>
> +struct xhci_pci_plat {
> + struct reset_ctl reset;
> +};
> +
> static int xhci_pci_init(struct udevice *dev, struct xhci_hccr **ret_hccr,
> struct xhci_hcor **ret_hcor)
> {
> @@ -45,15 +50,53 @@ static int xhci_pci_init(struct udevice *dev, struct xhci_hccr **ret_hccr,
>
> static int xhci_pci_probe(struct udevice *dev)
> {
> + struct xhci_pci_plat = dev_get_plat(dev);
> struct xhci_hccr *hccr;
> struct xhci_hcor *hcor;
> int ret;
>
> + ret = reset_get_by_index(dev, 0, &plat->reset);
> + if (ret && ret != -ENOENT && ret != -ENOTSUPP) {
> + dev_err(dev, "failed to get reset\n");
> + return ret;
> + }
> +
> + if (reset_valid(&plat->reset)) {
> + ret = reset_assert(&plat->reset);
> + if (ret)
> + goto err_reset;
> +
> + ret = reset_deassert(&plat->reset);
> + if (ret)
> + goto err_reset;
> + }
> +
> ret = xhci_pci_init(dev, &hccr, &hcor);
> if (ret)
> - return ret;
> + goto err_reset;
> +
> + ret = xhci_register(dev, hccr, hcor);
> + if (ret)
> + goto err_reset;
> +
> + return 0;
> +
> +err_reset:
> + if (reset_valid(&plat->reset))
> + reset_free(&plat->reset);
> +
> + return ret;
> +}
> +
> +static int xhci_pci_remove(struct udevice *dev)
> +{
> + struct xhci_pci_plat = dev_get_plat(dev);
>
> - return xhci_register(dev, hccr, hcor);
> + xhci_deregister(dev);
> + if (reset_valid(&plat->reset))
> + reset_free(&plat->reset);
> +
> + return 0;
> }
>
> static const struct udevice_id xhci_pci_ids[] = {
> @@ -65,10 +108,10 @@ U_BOOT_DRIVER(xhci_pci) = {
> .name = "xhci_pci",
> .id = UCLASS_USB,
> .probe = xhci_pci_probe,
> - .remove = xhci_deregister,
> + .remove = xhci_pci_remove,
> .of_match = xhci_pci_ids,
> .ops = &xhci_usb_ops,
> - .plat_auto = sizeof(struct usb_plat),
> + .plat_auto = sizeof(struct xhci_pci_plat),
> .priv_auto = sizeof(struct xhci_ctrl),
> .flags = DM_FLAG_OS_PREPARE | DM_FLAG_ALLOC_PRIV_DMA,
> };
> diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
> index d27ac01c83..452dacc0af 100644
> --- a/drivers/usb/host/xhci.c
> +++ b/drivers/usb/host/xhci.c
> @@ -188,37 +188,6 @@ static int xhci_start(struct xhci_hcor *hcor)
> return ret;
> }
>
> -#if CONFIG_IS_ENABLED(DM_USB)
> -/**
> - * Resets XHCI Hardware
> - *
> - * @param ctrl pointer to host controller
> - * @return 0 if OK, or a negative error code.
> - */
> -static int xhci_reset_hw(struct xhci_ctrl *ctrl)
> -{
> - int ret;
> -
> - ret = reset_get_by_index(ctrl->dev, 0, &ctrl->reset);
> - if (ret && ret != -ENOENT && ret != -ENOTSUPP) {
> - dev_err(ctrl->dev, "failed to get reset\n");
> - return ret;
> - }
> -
> - if (reset_valid(&ctrl->reset)) {
> - ret = reset_assert(&ctrl->reset);
> - if (ret)
> - return ret;
> -
> - ret = reset_deassert(&ctrl->reset);
> - if (ret)
> - return ret;
> - }
> -
> - return 0;
> -}
> -#endif
> -
> /**
> * Resets the XHCI Controller
> *
> @@ -1534,10 +1503,6 @@ int xhci_register(struct udevice *dev, struct xhci_hccr *hccr,
>
> ctrl->dev = dev;
>
> - ret = xhci_reset_hw(ctrl);
> - if (ret)
> - goto err;
> -
> /*
> * XHCI needs to issue a Address device command to setup
> * proper device context structures, before it can interact
> diff --git a/include/usb/xhci.h b/include/usb/xhci.h
> index 8d95e213b0..01e63cf0fc 100644
> --- a/include/usb/xhci.h
> +++ b/include/usb/xhci.h
> @@ -17,7 +17,6 @@
> #define HOST_XHCI_H_
>
> #include <phys2bus.h>
> -#include <reset.h>
> #include <asm/types.h>
> #include <asm/cache.h>
> #include <asm/io.h>
> @@ -1200,7 +1199,6 @@ struct xhci_ctrl {
> #if CONFIG_IS_ENABLED(DM_USB)
> struct udevice *dev;
> #endif
> - struct reset_ctl reset;
> struct xhci_hccr *hccr; /* R/O registers, not need for volatile */
> struct xhci_hcor *hcor;
> struct xhci_doorbell_array *dba;
next prev parent reply other threads:[~2021-04-21 10:36 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-04-17 14:20 [PATCH v2 0/4] Allwinner H6 USB3 support Samuel Holland
2021-04-17 14:20 ` [PATCH v2 1/4] phy: sun50i-usb3: Add a driver for the H6 USB3 PHY Samuel Holland
2021-04-17 14:20 ` [PATCH v2 2/4] usb: xhci-pci: Move reset logic out of XHCI core Samuel Holland
2021-04-21 10:36 ` Andre Przywara [this message]
2021-04-21 13:36 ` Samuel Holland
2021-04-21 14:58 ` Andre Przywara
2021-07-05 8:04 ` Bin Meng
2021-07-05 8:19 ` Marek Vasut
2021-07-05 8:38 ` Bin Meng
2021-07-05 9:06 ` Andre Przywara
2021-07-05 9:18 ` Bin Meng
2021-07-05 10:45 ` Marek Vasut
2021-07-05 12:12 ` Andre Przywara
2021-07-05 9:20 ` Marek Vasut
2021-04-17 14:20 ` [PATCH v2 3/4] usb: xhci-dwc3: Add support for clocks/resets Samuel Holland
2021-04-21 10:37 ` Andre Przywara
2021-04-17 14:20 ` [PATCH v2 4/4] configs: Enable USB3 on Allwinner H6 boards Samuel Holland
2021-04-21 10:37 ` Andre Przywara
2021-04-21 10:43 ` [PATCH v2 0/4] Allwinner H6 USB3 support Andre Przywara
2021-04-21 10:53 ` Marek Vasut
2021-07-04 23:09 ` Andre Przywara
2021-07-05 1:18 ` Bin Meng
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210421113638.47770202@slackpad.fritz.box \
--to=andre.przywara@arm.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox