From: Kishon Vijay Abraham I <kishon@ti.com>
To: u-boot@lists.denx.de
Subject: [PATCH v3 19/20] env: ti: j721e-evm: Add env variable to power on & reset QSGMII PHY in J7200 EVM
Date: Tue, 4 May 2021 16:11:54 +0530 [thread overview]
Message-ID: <20210504104155.19222-20-kishon@ti.com> (raw)
In-Reply-To: <20210504104155.19222-1-kishon@ti.com>
MAIN CPSW0 requires the PHY to be powered on and reset for QSGMII
operation. Add a env variable to configure driving "0" on ENET_EXP_PWRDN
controlled by GPIO EXPANDER2 (I2C Addr: 0x22), PIN: 17 and driving "1"
on ENET_EXP_RESETZ controlled by GPIO EXPANDER2 (I2C Addr: 0x22),
PIN: 18.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
---
include/configs/j721e_evm.h | 16 +++++++++++++++-
1 file changed, 15 insertions(+), 1 deletion(-)
diff --git a/include/configs/j721e_evm.h b/include/configs/j721e_evm.h
index b707fc4e89..00d0a18a68 100644
--- a/include/configs/j721e_evm.h
+++ b/include/configs/j721e_evm.h
@@ -139,11 +139,24 @@
#endif /* CONFIG_TARGET_J721E_A72_EVM */
#ifdef CONFIG_TARGET_J7200_A72_EVM
+#define EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY \
+ "do_main_cpsw0_qsgmii_phyinit=1\0" \
+ "init_main_cpsw0_qsgmii_phy=gpio set gpio at 22_17;" \
+ "gpio clear gpio at 22_16\0" \
+ "main_cpsw0_qsgmii_phyinit=" \
+ "if test ${do_main_cpsw0_qsgmii_phyinit} -eq 1 && test ${dorprocboot} -eq 1 && " \
+ "test ${boot} = mmc; then " \
+ "run init_main_cpsw0_qsgmii_phy;" \
+ "fi;\0"
#define DEFAULT_RPROCS "" \
"2 /lib/firmware/j7200-main-r5f0_0-fw " \
"3 /lib/firmware/j7200-main-r5f0_1-fw "
#endif /* CONFIG_TARGET_J7200_A72_EVM */
+#ifndef EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY
+#define EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY
+#endif
+
/* set default dfu_bufsiz to 128KB (sector size of OSPI) */
#define EXTRA_ENV_DFUARGS \
"dfu_bufsiz=0x20000\0" \
@@ -170,7 +183,8 @@
EXTRA_ENV_RPROC_SETTINGS \
EXTRA_ENV_DFUARGS \
DEFAULT_UFS_TI_ARGS \
- EXTRA_ENV_J721E_BOARD_SETTINGS_MTD
+ EXTRA_ENV_J721E_BOARD_SETTINGS_MTD \
+ EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY
/* Now for the remaining common defines */
#include <configs/ti_armv7_common.h>
--
2.17.1
next prev parent reply other threads:[~2021-05-04 10:41 UTC|newest]
Thread overview: 36+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-05-04 10:41 [PATCH v3 00/20] TI/Cadence: Add Sierra/Torrent SERDES driver Kishon Vijay Abraham I
2021-05-04 10:41 ` [PATCH v3 01/20] dm: core: Add helper to compare node names Kishon Vijay Abraham I
2021-05-04 16:58 ` Simon Glass
2021-05-04 10:41 ` [PATCH v3 02/20] dm: test: Add test case to check node name ignoring unit address Kishon Vijay Abraham I
2021-05-04 10:41 ` [PATCH v3 03/20] drivers: reset: Handle gracefully NULL pointers Kishon Vijay Abraham I
2021-05-04 16:58 ` Simon Glass
2021-05-05 4:25 ` Kishon Vijay Abraham I
2021-05-05 23:37 ` Simon Glass
2021-05-06 13:09 ` Kishon Vijay Abraham I
2021-05-06 15:06 ` Simon Glass
2021-05-04 10:41 ` [PATCH v3 04/20] dt-bindings: phy: Add definitions for additional phy types Kishon Vijay Abraham I
2021-05-04 10:41 ` [PATCH v3 05/20] dt-bindings: phy: Add defines for AM64 SERDES Wrapper Kishon Vijay Abraham I
2021-05-04 10:41 ` [PATCH v3 06/20] dt-bindings: phy: cadence-torrent: Add defines for refclk driver Kishon Vijay Abraham I
2021-05-04 10:41 ` [PATCH v3 07/20] dt-bindings: ti-serdes-mux: Add defines for AM64 SoC Kishon Vijay Abraham I
2021-05-04 10:41 ` [PATCH v3 08/20] phy: cadence: Add driver for Sierra PHY Kishon Vijay Abraham I
2021-05-04 10:41 ` [PATCH v3 09/20] phy: cadence: Add driver for Torrent SERDES Kishon Vijay Abraham I
2021-05-04 10:41 ` [PATCH v3 10/20] phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC Kishon Vijay Abraham I
2021-05-04 10:41 ` [PATCH v3 11/20] usb: cdns3: cdns3-ti: Fix clk_get_by_name() to get the correct name Kishon Vijay Abraham I
2021-05-04 10:41 ` [PATCH v3 12/20] board: ti: j721e: Add support for probing and configuring Torrent serdes on J7200 Kishon Vijay Abraham I
2021-05-04 10:41 ` [PATCH v3 13/20] ARM: dts: k3-j721e: Add the entries required for USB3 support on USB0 Kishon Vijay Abraham I
2021-05-07 17:14 ` Tom Rini
2021-07-09 14:06 ` Kishon Vijay Abraham I
2021-07-09 14:16 ` Tom Rini
2021-05-04 10:41 ` [PATCH v3 14/20] arm: dts: k3-j7200-main: Add DT node for torrent serdes Kishon Vijay Abraham I
2021-05-04 10:41 ` [PATCH v3 15/20] arm: dts: k3-j7200-common-proc-board: Enable SERDES DT Kishon Vijay Abraham I
2021-05-04 10:41 ` [PATCH v3 16/20] arm: dts: k3-j7200-common-proc-board-u-boot: Add u-boot tags for torrent serdes Kishon Vijay Abraham I
2021-05-04 10:41 ` [PATCH v3 17/20] configs: j721e_evm_a72: Enable the drivers required for the USB3 support Kishon Vijay Abraham I
2021-05-04 10:41 ` [PATCH v3 18/20] configs: j7200_evm_a72_defconfig: Add config for torrent serdes and common clock framework Kishon Vijay Abraham I
2021-05-04 10:41 ` Kishon Vijay Abraham I [this message]
2021-05-07 17:14 ` [PATCH v3 19/20] env: ti: j721e-evm: Add env variable to power on & reset QSGMII PHY in J7200 EVM Tom Rini
2021-05-11 13:58 ` Kishon Vijay Abraham I
2021-05-11 14:33 ` Tom Rini
2021-07-09 14:32 ` Kishon Vijay Abraham I
2021-07-09 14:36 ` Tom Rini
2021-05-04 10:41 ` [PATCH v3 20/20] configs: j7200_evm_a72: Enhance bootcmd to configure ethernet PHY Kishon Vijay Abraham I
2021-05-07 17:16 ` [PATCH v3 00/20] TI/Cadence: Add Sierra/Torrent SERDES driver Tom Rini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210504104155.19222-20-kishon@ti.com \
--to=kishon@ti.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox