[PATCH] arm: imx: imx8mm: correct unrecognized fracpll frequency

[PATCH] arm: imx: imx8mm: correct unrecognized fracpll frequency

[Andrey Zhizhikin]

Frequency requested by ddrphy_init_set_dfi_clk from fracpll uses MHZ()
macro, which expands the value provided to the Hz range without taking into
account the precise Hz setting. This causes the frequency of 266 MHz not ot
be found in the imx8mm_fracpll_tbl, since it is entered there with a
precise Hz value. This in turn causes the boot hang in SPL, as proper DDR
fracpll frequency cannot be determined.

Correct the value in imx8mm_fracpll_tbl to match the one expanded by
MHZ(266) macro, rounding it down to MHz range only.

Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Fixes: 825ab6b406 ("driver: ddr: Refine the ddr init driver on imx8m")
---
 arch/arm/mach-imx/imx8m/clock_imx8mm.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/mach-imx/imx8m/clock_imx8mm.c b/arch/arm/mach-imx/imx8m/clock_imx8mm.c
index 029d06f27f..86ff2b9cc9 100644
--- a/arch/arm/mach-imx/imx8m/clock_imx8mm.c
+++ b/arch/arm/mach-imx/imx8m/clock_imx8mm.c
@@ -54,7 +54,7 @@ static struct imx_int_pll_rate_table imx8mm_fracpll_tbl[] = {
 	PLL_1443X_RATE(600000000U, 300, 3, 2, 0),
 	PLL_1443X_RATE(594000000U, 99, 1, 2, 0),
 	PLL_1443X_RATE(400000000U, 300, 9, 1, 0),
-	PLL_1443X_RATE(266666667U, 400, 9, 2, 0),
+	PLL_1443X_RATE(266000000U, 400, 9, 2, 0),
 	PLL_1443X_RATE(167000000U, 334, 3, 4, 0),
 	PLL_1443X_RATE(100000000U, 300, 9, 3, 0),
 };
@@ -72,7 +72,7 @@ static int fracpll_configure(enum pll_clocks pll, u32 freq)
 	}
 
 	if (i == ARRAY_SIZE(imx8mm_fracpll_tbl)) {
-		printf("No matched freq table %u\n", freq);
+		printf("%s: No matched freq table %u\n", __func__, freq);
 		return -EINVAL;
 	}
 
@@ -148,7 +148,7 @@ void dram_enable_bypass(ulong clk_val)
 	}
 
 	if (i == ARRAY_SIZE(imx8mm_dram_bypass_tbl)) {
-		printf("No matched freq table %lu\n", clk_val);
+		printf("%s: No matched freq table %lu\n", __func__, clk_val);
 		return;
 	}
 
-- 
2.25.1

[PATCH] arm: imx: imx8mm: correct unrecognized fracpll frequency

[Fabio Estevam]

On Sat, May 1, 2021 at 5:13 PM Andrey Zhizhikin
<andrey.zhizhikin@leica-geosystems.com> wrote:
>
> Frequency requested by ddrphy_init_set_dfi_clk from fracpll uses MHZ()
> macro, which expands the value provided to the Hz range without taking into
> account the precise Hz setting. This causes the frequency of 266 MHz not ot
> be found in the imx8mm_fracpll_tbl, since it is entered there with a
> precise Hz value. This in turn causes the boot hang in SPL, as proper DDR
> fracpll frequency cannot be determined.
>
> Correct the value in imx8mm_fracpll_tbl to match the one expanded by
> MHZ(266) macro, rounding it down to MHz range only.
>
> Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
> Cc: Stefano Babic <sbabic@denx.de>
> Cc: Fabio Estevam <festevam@gmail.com>
> Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
> Cc: Peng Fan <peng.fan@nxp.com>
> Cc: Simon Glass <sjg@chromium.org>
> Cc: Ye Li <ye.li@nxp.com>
> Fixes: 825ab6b406 ("driver: ddr: Refine the ddr init driver on imx8m")

Reviewed-by: Fabio Estevam <festevam@gmail.com>

[PATCH] arm: imx: imx8mm: correct unrecognized fracpll frequency

[Fabio Estevam]

Hi Andrey,

After re-reading the patch I have some comments:

On Sat, May 1, 2021 at 5:13 PM Andrey Zhizhikin
<andrey.zhizhikin@leica-geosystems.com> wrote:
>
> Frequency requested by ddrphy_init_set_dfi_clk from fracpll uses MHZ()
> macro, which expands the value provided to the Hz range without taking into
> account the precise Hz setting. This causes the frequency of 266 MHz not ot
> be found in the imx8mm_fracpll_tbl, since it is entered there with a
> precise Hz value. This in turn causes the boot hang in SPL, as proper DDR
> fracpll frequency cannot be determined.
>
> Correct the value in imx8mm_fracpll_tbl to match the one expanded by
> MHZ(266) macro, rounding it down to MHz range only.
>
> Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
> Cc: Stefano Babic <sbabic@denx.de>
> Cc: Fabio Estevam <festevam@gmail.com>
> Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
> Cc: Peng Fan <peng.fan@nxp.com>
> Cc: Simon Glass <sjg@chromium.org>
> Cc: Ye Li <ye.li@nxp.com>
> Fixes: 825ab6b406 ("driver: ddr: Refine the ddr init driver on imx8m")
> ---
>  arch/arm/mach-imx/imx8m/clock_imx8mm.c | 6 +++---
>  1 file changed, 3 insertions(+), 3 deletions(-)
>
> diff --git a/arch/arm/mach-imx/imx8m/clock_imx8mm.c b/arch/arm/mach-imx/imx8m/clock_imx8mm.c
> index 029d06f27f..86ff2b9cc9 100644
> --- a/arch/arm/mach-imx/imx8m/clock_imx8mm.c
> +++ b/arch/arm/mach-imx/imx8m/clock_imx8mm.c
> @@ -54,7 +54,7 @@ static struct imx_int_pll_rate_table imx8mm_fracpll_tbl[] = {
>         PLL_1443X_RATE(600000000U, 300, 3, 2, 0),
>         PLL_1443X_RATE(594000000U, 99, 1, 2, 0),
>         PLL_1443X_RATE(400000000U, 300, 9, 1, 0),
> -       PLL_1443X_RATE(266666667U, 400, 9, 2, 0),
> +       PLL_1443X_RATE(266000000U, 400, 9, 2, 0),

This change looks good.

>         PLL_1443X_RATE(167000000U, 334, 3, 4, 0),
>         PLL_1443X_RATE(100000000U, 300, 9, 3, 0),
>  };
> @@ -72,7 +72,7 @@ static int fracpll_configure(enum pll_clocks pll, u32 freq)
>         }
>
>         if (i == ARRAY_SIZE(imx8mm_fracpll_tbl)) {
> -               printf("No matched freq table %u\n", freq);
> +               printf("%s: No matched freq table %u\n", __func__, freq);
>                 return -EINVAL;
>         }
>
> @@ -148,7 +148,7 @@ void dram_enable_bypass(ulong clk_val)
>         }
>
>         if (i == ARRAY_SIZE(imx8mm_dram_bypass_tbl)) {
> -               printf("No matched freq table %lu\n", clk_val);
> +               printf("%s: No matched freq table %lu\n", __func__, clk_val);

, but these two I would put them on a separate patch.

Thanks

[PATCH] arm: imx: imx8mm: correct unrecognized fracpll frequency

[ZHIZHIKIN Andrey]

Hello Fabio,

> -----Original Message-----
> From: Fabio Estevam <festevam@gmail.com>
> Sent: Sunday, May 2, 2021 11:45 PM
> To: ZHIZHIKIN Andrey <andrey.zhizhikin@leica-geosystems.com>
> Cc: U-Boot-Denx <u-boot@lists.denx.de>; Stefano Babic <sbabic@denx.de>;
> NXP i.MX U-Boot Team <uboot-imx@nxp.com>; Peng Fan
> <peng.fan@nxp.com>; Simon Glass <sjg@chromium.org>; Ye Li <ye.li@nxp.com>
> Subject: Re: [PATCH] arm: imx: imx8mm: correct unrecognized fracpll frequency
> 
> 
> Hi Andrey,
> 
> After re-reading the patch I have some comments:
> 
> On Sat, May 1, 2021 at 5:13 PM Andrey Zhizhikin <andrey.zhizhikin@leica-
> geosystems.com> wrote:
> >
> > Frequency requested by ddrphy_init_set_dfi_clk from fracpll uses MHZ()
> > macro, which expands the value provided to the Hz range without taking
> > into account the precise Hz setting. This causes the frequency of 266
> > MHz not ot be found in the imx8mm_fracpll_tbl, since it is entered
> > there with a precise Hz value. This in turn causes the boot hang in
> > SPL, as proper DDR fracpll frequency cannot be determined.
> >
> > Correct the value in imx8mm_fracpll_tbl to match the one expanded by
> > MHZ(266) macro, rounding it down to MHz range only.
> >
> > Signed-off-by: Andrey Zhizhikin
> > <andrey.zhizhikin@leica-geosystems.com>
> > Cc: Stefano Babic <sbabic@denx.de>
> > Cc: Fabio Estevam <festevam@gmail.com>
> > Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
> > Cc: Peng Fan <peng.fan@nxp.com>
> > Cc: Simon Glass <sjg@chromium.org>
> > Cc: Ye Li <ye.li@nxp.com>
> > Fixes: 825ab6b406 ("driver: ddr: Refine the ddr init driver on imx8m")
> > ---
> >  arch/arm/mach-imx/imx8m/clock_imx8mm.c | 6 +++---
> >  1 file changed, 3 insertions(+), 3 deletions(-)
> >
> > diff --git a/arch/arm/mach-imx/imx8m/clock_imx8mm.c
> > b/arch/arm/mach-imx/imx8m/clock_imx8mm.c
> > index 029d06f27f..86ff2b9cc9 100644
> > --- a/arch/arm/mach-imx/imx8m/clock_imx8mm.c
> > +++ b/arch/arm/mach-imx/imx8m/clock_imx8mm.c
> > @@ -54,7 +54,7 @@ static struct imx_int_pll_rate_table imx8mm_fracpll_tbl[]
> = {
> >         PLL_1443X_RATE(600000000U, 300, 3, 2, 0),
> >         PLL_1443X_RATE(594000000U, 99, 1, 2, 0),
> >         PLL_1443X_RATE(400000000U, 300, 9, 1, 0),
> > -       PLL_1443X_RATE(266666667U, 400, 9, 2, 0),
> > +       PLL_1443X_RATE(266000000U, 400, 9, 2, 0),
> 
> This change looks good.
> 
> >         PLL_1443X_RATE(167000000U, 334, 3, 4, 0),
> >         PLL_1443X_RATE(100000000U, 300, 9, 3, 0),  }; @@ -72,7 +72,7
> > @@ static int fracpll_configure(enum pll_clocks pll, u32 freq)
> >         }
> >
> >         if (i == ARRAY_SIZE(imx8mm_fracpll_tbl)) {
> > -               printf("No matched freq table %u\n", freq);
> > +               printf("%s: No matched freq table %u\n", __func__,
> > + freq);
> >                 return -EINVAL;
> >         }
> >
> > @@ -148,7 +148,7 @@ void dram_enable_bypass(ulong clk_val)
> >         }
> >
> >         if (i == ARRAY_SIZE(imx8mm_dram_bypass_tbl)) {
> > -               printf("No matched freq table %lu\n", clk_val);
> > +               printf("%s: No matched freq table %lu\n", __func__,
> > + clk_val);
> 
> , but these two I would put them on a separate patch.

Fair enough, thanks for pointing this out!

Even though this helped me originally to pinpoint the issue, looking at this change now I see it does indeed belong to the separate patch as it does not relate to the PLL fix per se.

I would split this into a separate patch, send it separate, and send a V2 for the PLL fix.

> 
> Thanks

Cheers,
Andrey

[PATCH v2] arm: imx: imx8mm: correct unrecognized fracpll frequency

[Andrey Zhizhikin]

Frequency requested by ddrphy_init_set_dfi_clk from fracpll uses MHZ()
macro, which expands the value provided to the Hz range without taking into
account the precise Hz setting. This causes the frequency of 266 MHz not ot
be found in the imx8mm_fracpll_tbl, since it is entered there with a
precise Hz value. This in turn causes the boot hang in SPL, as proper DDR
fracpll frequency cannot be determined.

Correct the value in imx8mm_fracpll_tbl to match the one expanded by
MHZ(266) macro, rounding it down to MHz range only.

Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Fixes: 825ab6b406 ("driver: ddr: Refine the ddr init driver on imx8m")
---

Changes in v2:
- Remove debug message clarifications, they are addressed in a separate
  patch

 arch/arm/mach-imx/imx8m/clock_imx8mm.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/mach-imx/imx8m/clock_imx8mm.c b/arch/arm/mach-imx/imx8m/clock_imx8mm.c
index 029d06f27f..7d0f564a24 100644
--- a/arch/arm/mach-imx/imx8m/clock_imx8mm.c
+++ b/arch/arm/mach-imx/imx8m/clock_imx8mm.c
@@ -54,7 +54,7 @@ static struct imx_int_pll_rate_table imx8mm_fracpll_tbl[] = {
 	PLL_1443X_RATE(600000000U, 300, 3, 2, 0),
 	PLL_1443X_RATE(594000000U, 99, 1, 2, 0),
 	PLL_1443X_RATE(400000000U, 300, 9, 1, 0),
-	PLL_1443X_RATE(266666667U, 400, 9, 2, 0),
+	PLL_1443X_RATE(266000000U, 400, 9, 2, 0),
 	PLL_1443X_RATE(167000000U, 334, 3, 4, 0),
 	PLL_1443X_RATE(100000000U, 300, 9, 3, 0),
 };
-- 
2.25.1

[PATCH v2] arm: imx: imx8mm: correct unrecognized fracpll frequency

[Fabio Estevam]

On Mon, May 3, 2021 at 5:00 AM Andrey Zhizhikin
<andrey.zhizhikin@leica-geosystems.com> wrote:
>
> Frequency requested by ddrphy_init_set_dfi_clk from fracpll uses MHZ()
> macro, which expands the value provided to the Hz range without taking into
> account the precise Hz setting. This causes the frequency of 266 MHz not ot
> be found in the imx8mm_fracpll_tbl, since it is entered there with a
> precise Hz value. This in turn causes the boot hang in SPL, as proper DDR
> fracpll frequency cannot be determined.
>
> Correct the value in imx8mm_fracpll_tbl to match the one expanded by
> MHZ(266) macro, rounding it down to MHz range only.
>
> Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
> Cc: Stefano Babic <sbabic@denx.de>
> Cc: Fabio Estevam <festevam@gmail.com>
> Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
> Cc: Peng Fan <peng.fan@nxp.com>
> Cc: Simon Glass <sjg@chromium.org>
> Cc: Ye Li <ye.li@nxp.com>
> Fixes: 825ab6b406 ("driver: ddr: Refine the ddr init driver on imx8m")

Reviewed-by: Fabio Estevam <festevam@gmail.com>

[PATCH v2] arm: imx: imx8mm: correct unrecognized fracpll frequency

[sbabic]

> Frequency requested by ddrphy_init_set_dfi_clk from fracpll uses MHZ()
> macro, which expands the value provided to the Hz range without taking into
> account the precise Hz setting. This causes the frequency of 266 MHz not ot
> be found in the imx8mm_fracpll_tbl, since it is entered there with a
> precise Hz value. This in turn causes the boot hang in SPL, as proper DDR
> fracpll frequency cannot be determined.
> Correct the value in imx8mm_fracpll_tbl to match the one expanded by
> MHZ(266) macro, rounding it down to MHz range only.
> Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
> Cc: Stefano Babic <sbabic@denx.de>
> Cc: Fabio Estevam <festevam@gmail.com>
> Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
> Cc: Peng Fan <peng.fan@nxp.com>
> Cc: Simon Glass <sjg@chromium.org>
> Cc: Ye Li <ye.li@nxp.com>
> Fixes: 825ab6b406 ("driver: ddr: Refine the ddr init driver on imx8m")
> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================