Re: [PATCH V3] sf: Querying write-protect status before operating the flash

[Tom Rini <trini@konsulko.com>]

[-- Attachment #1: Type: text/plain, Size: 3218 bytes --]

On Wed, Nov 17, 2021 at 01:43:28PM +0530, Jagan Teki wrote:
> On Wed, Nov 17, 2021 at 1:33 PM Michael Walle <michael@walle.cc> wrote:
> >
> > Hi,
> >
> > Am 2021-11-17 03:48, schrieb chaochao2021666@163.com:
> > > From: chao zeng <chao.zeng@siemens.com>
> > >
> > > When operating the write-protection flash,spi_flash_std_write() and
> > > spi_flash_std_erase() would return wrong result.The flash is protected,
> > > but write or erase the flash would show "OK".
> > >
> > > Check the flash write protection state before operating the flash
> > > and give a prompt to show it has been locked if the write-protection
> > > has enbale
> > >
> > > Signed-off-by: chao zeng <chao.zeng@siemens.com>
> > >
> > > ---
> > >
> > > Changes for V2:
> > >      - Return 0 not ENOPROTOOPT to refelect the flash feature
> > >      - Output prompt information
> > > Changes for V3:
> > >      - Modify output information
> > >      - Delete return statement
> > > ---
> > >  drivers/mtd/spi/sf_probe.c | 6 ++++++
> > >  1 file changed, 6 insertions(+)
> > >
> > > diff --git a/drivers/mtd/spi/sf_probe.c b/drivers/mtd/spi/sf_probe.c
> > > index f461082e03..f9e879aec5 100644
> > > --- a/drivers/mtd/spi/sf_probe.c
> > > +++ b/drivers/mtd/spi/sf_probe.c
> > > @@ -109,6 +109,9 @@ static int spi_flash_std_write(struct udevice
> > > *dev, u32 offset, size_t len,
> > >       struct mtd_info *mtd = &flash->mtd;
> > >       size_t retlen;
> > >
> > > +     if (flash->flash_is_locked && flash->flash_is_locked(flash, offset,
> > > len))
> > > +             printf("SF: Operate on the protected area.Writes will be
> > > ignored\n");
> >
> > I don't think this is the correct place for this output. This could
> > also be called from a board file programmatically and then it might
> > display this error, which is annoying.
> >
> > Also, this is issuing an additional command "read SR" for every write.
> >
> > What is your intention here? To make the user aware that he is going
> > to write to a write-protected region when he is using the "sf" command?
> > If that is the case, this should be added to that command instead.
> >
> > > +
> > >       return mtd->_write(mtd, offset, len, &retlen, buf);
> > >  }
> > >
> > > @@ -127,6 +130,9 @@ static int spi_flash_std_erase(struct udevice
> > > *dev, u32 offset, size_t len)
> > >       instr.addr = offset;
> > >       instr.len = len;
> > >
> > > +     if (flash->flash_is_locked && flash->flash_is_locked(flash, offset,
> > > len))
> > > +             printf("SF: Operate on the protected area.Erase will be ignored\n");
> 
> My fundamental question, why cannot we use 'sf protect' then 'sf write'?

Where do we tell people to always run "sf protect" before "sf write" and
why is that at all user friendly?  No, we shouldn't run this test more
than once per time we're told to write an image.  But silently failing
in cases we can detect a problem is also not correct.  If it's possible
to spot this easily with "sf protect" why not just do that as part of
"sf write" and add a flag to skip the check if you know it's not needed?
I assume it's a fairly cheap/quick operation to do this check.

-- 
Tom

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 659 bytes --]