[PATCH v2 0/8] Add MV88E61xx DSA driver and use on gwventana

[Tim Harvey <tharvey@gateworks.com>]

This series adds a DSA driver for the MV88E61xx based on
drivers/net/phy/mv88e61xx and uses in on the gwventana_gw5904_defconfig.

The hope is that the other three boards that use the MV88E61xx driver
can move to this as well eventually so that we can remove the non-dm
driver and the 4 Kconfig options it requires.

The MV88E61xx has an MDIO interface thus DM_MDIO must be used so support
for a UCLASS_MDIO driver is added to the fec_mxc ethernet driver in a
way that allows a fallback to the previous non DM_MDIO case as there are
many boards out there using this driver that define DM_MDIO but do not
have the required dt props for a DM_MDIO driver which would cause a
regression.

Additionally some other patches are here suggested by Vladimir:
 - ensure MDIO children are scanned on post-bind is needed
 - sanity check DSA driver required ops are present
 - allow DSA drivers to not require xmit/recv functions
 - remove unecessary xmit/recv functions from ksz9477 driver

v2:
 - added Ramon's rb tag's to first two patches
 - add patches for dsa-uclass to sanity check ops and make xmit/recv
   optional
 - fec: fix fallback for non conforming DM_MDIO dts
 - mv88e61xx:
  - rebase on v2022.07-rc2 (use ofnode_get_phy_node)
  - remove unused commented out fields from struct
  - remove unused PORT_MASK macro
  - remove phy from priv struct name
  - refactor code from original drivers/net/phy/mv88e61xx with
    suggestions from review to consolidate some functions
    into mv88e61xx_dsa_port_enable
  - remove unecessary skiping of disabling of CPU port
  - remove unecessary dev_set_parent_priv
  - remove unnecessary static init flag
  - replace debug with a dev_warn if switch device-id unsupported
  - remove unnecessary xmit/recv functions as we rely on the fact that
    only a single port is active instead of mangling packets

Tested on a Gateworks GW5904 which has a Marvell 88E6176 switch hanging
off the IMX6 FEC.

Best Regards,

Tim

Tim Harvey (8):
  net: mdio-uclass: scan for dm mdio children on post-bind
  net: dsa: move cpu port probe to dsa_post_probe
  net: dsa: ensure dsa driver has proper ops
  net: dsa: allow rcv() and xmit() to be optional
  net: ksz9477: remove unnecessary xmit and recv functions
  net: fec: add support for DM_MDIO
  net: add MV88E61xx DSA driver
  board: gw_ventana: enable MV88E61XX DSA support

 arch/arm/dts/imx6qdl-gw5904.dtsi        |  35 +
 board/gateworks/gw_ventana/gw_ventana.c |  50 +-
 configs/gwventana_gw5904_defconfig      |   7 +-
 drivers/net/Kconfig                     |   7 +
 drivers/net/Makefile                    |   1 +
 drivers/net/fec_mxc.c                   |  90 ++-
 drivers/net/ksz9477.c                   |  23 -
 drivers/net/mv88e61xx.c                 | 843 ++++++++++++++++++++++++
 net/dsa-uclass.c                        |  58 +-
 net/mdio-uclass.c                       |   4 +
 10 files changed, 1045 insertions(+), 73 deletions(-)
 create mode 100644 drivers/net/mv88e61xx.c

-- 
2.17.1