public inbox for u-boot@lists.denx.de
 help / color / mirror / Atom feed
From: Heiko Thiery <heiko.thiery@gmail.com>
To: u-boot@lists.denx.de
Cc: Jaehoon Chung <jh80.chung@samsung.com>,
	Heiko Thiery <heiko.thiery@gmail.com>,
	Marek Vasut <marex@denx.de>, Fabio Estevam <festevam@denx.de>,
	Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Subject: [PATCH] pmic: pca9450: permit config on all bucks and LDOs
Date: Mon, 20 Jun 2022 05:49:49 +0200	[thread overview]
Message-ID: <20220620034948.646319-1-heiko.thiery@gmail.com> (raw)

In order to have the possibility to configure the regulators at system
startup through DM support, all LDOs and bucks must be able to be
changeable. Currently there is a limitation to change the values when
the output is enabled. Since the driver is based on the ROHM BD71837 and a
comment that describes a limitation about switching while the output is
enabled can also be found there, the limitation probably comes from this type.

Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
---
 drivers/power/regulator/pca9450.c | 42 ++++++++++---------------------
 1 file changed, 13 insertions(+), 29 deletions(-)

diff --git a/drivers/power/regulator/pca9450.c b/drivers/power/regulator/pca9450.c
index 23badaa332..fe1869397c 100644
--- a/drivers/power/regulator/pca9450.c
+++ b/drivers/power/regulator/pca9450.c
@@ -44,7 +44,6 @@ struct pca9450_vrange {
  * @ranges:	pointer to ranges of regulator voltages and matching register
  *		values
  * @numranges:	number of voltage ranges pointed by ranges
- * @dvs:	whether the voltage can be changed when regulator is enabled
  */
 struct pca9450_plat {
 	const char		*name;
@@ -54,7 +53,6 @@ struct pca9450_plat {
 	u8			volt_mask;
 	struct pca9450_vrange	*ranges;
 	unsigned int		numranges;
-	bool			dvs;
 };
 
 #define PCA_RANGE(_min, _vstep, _sel_low, _sel_hi) \
@@ -63,11 +61,11 @@ struct pca9450_plat {
 	.min_sel = (_sel_low), .max_sel = (_sel_hi), \
 }
 
-#define PCA_DATA(_name, enreg, enmask, vreg, vmask, _range, _dvs) \
+#define PCA_DATA(_name, enreg, enmask, vreg, vmask, _range) \
 { \
 	.name = (_name), .enable_reg = (enreg), .enablemask = (enmask), \
 	.volt_reg = (vreg), .volt_mask = (vmask), .ranges = (_range), \
-	.numranges = ARRAY_SIZE(_range), .dvs = (_dvs), \
+	.numranges = ARRAY_SIZE(_range) \
 }
 
 static struct pca9450_vrange pca9450_buck123_vranges[] = {
@@ -107,39 +105,39 @@ static struct pca9450_plat pca9450_reg_data[] = {
 	/* Bucks 1-3 which support dynamic voltage scaling */
 	PCA_DATA("BUCK1", PCA9450_BUCK1CTRL, HW_STATE_CONTROL,
 		 PCA9450_BUCK1OUT_DVS0, PCA9450_DVS_BUCK_RUN_MASK,
-		 pca9450_buck123_vranges, true),
+		 pca9450_buck123_vranges),
 	PCA_DATA("BUCK2", PCA9450_BUCK2CTRL, HW_STATE_CONTROL,
 		 PCA9450_BUCK2OUT_DVS0, PCA9450_DVS_BUCK_RUN_MASK,
-		 pca9450_buck123_vranges, true),
+		 pca9450_buck123_vranges),
 	PCA_DATA("BUCK3", PCA9450_BUCK3CTRL, HW_STATE_CONTROL,
 		 PCA9450_BUCK3OUT_DVS0, PCA9450_DVS_BUCK_RUN_MASK,
-		 pca9450_buck123_vranges, true),
+		 pca9450_buck123_vranges),
 	/* Bucks 4-6 which do not support dynamic voltage scaling */
 	PCA_DATA("BUCK4", PCA9450_BUCK4CTRL, HW_STATE_CONTROL,
 		 PCA9450_BUCK4OUT, PCA9450_DVS_BUCK_RUN_MASK,
-		 pca9450_buck456_vranges, false),
+		 pca9450_buck456_vranges),
 	PCA_DATA("BUCK5", PCA9450_BUCK5CTRL, HW_STATE_CONTROL,
 		 PCA9450_BUCK5OUT, PCA9450_DVS_BUCK_RUN_MASK,
-		 pca9450_buck456_vranges, false),
+		 pca9450_buck456_vranges),
 	PCA_DATA("BUCK6", PCA9450_BUCK6CTRL, HW_STATE_CONTROL,
 		 PCA9450_BUCK6OUT, PCA9450_DVS_BUCK_RUN_MASK,
-		 pca9450_buck456_vranges, false),
+		 pca9450_buck456_vranges),
 	/* LDOs */
 	PCA_DATA("LDO1", PCA9450_LDO1CTRL, HW_STATE_CONTROL,
 		 PCA9450_LDO1CTRL, PCA9450_LDO12_MASK,
-		 pca9450_ldo1_vranges, false),
+		 pca9450_ldo1_vranges),
 	PCA_DATA("LDO2", PCA9450_LDO2CTRL, HW_STATE_CONTROL,
 		 PCA9450_LDO2CTRL, PCA9450_LDO12_MASK,
-		 pca9450_ldo2_vranges, false),
+		 pca9450_ldo2_vranges),
 	PCA_DATA("LDO3", PCA9450_LDO3CTRL, HW_STATE_CONTROL,
 		 PCA9450_LDO3CTRL, PCA9450_LDO34_MASK,
-		 pca9450_ldo34_vranges, false),
+		 pca9450_ldo34_vranges),
 	PCA_DATA("LDO4", PCA9450_LDO4CTRL, HW_STATE_CONTROL,
 		 PCA9450_LDO4CTRL, PCA9450_LDO34_MASK,
-		 pca9450_ldo34_vranges, false),
+		 pca9450_ldo34_vranges),
 	PCA_DATA("LDO5", PCA9450_LDO5CTRL_H, HW_STATE_CONTROL,
 		 PCA9450_LDO5CTRL_H, PCA9450_LDO5_MASK,
-		 pca9450_ldo5_vranges, false),
+		 pca9450_ldo5_vranges),
 };
 
 static int vrange_find_value(struct pca9450_vrange *r, unsigned int sel,
@@ -246,20 +244,6 @@ static int pca9450_set_value(struct udevice *dev, int uvolt)
 	unsigned int sel;
 	int i, found = 0;
 
-	/*
-	 * An under/overshooting may occur if voltage is changed for other
-	 * regulators but buck 1,2,3 or 4 when regulator is enabled. Prevent
-	 * change to protect the HW
-	 */
-	if (!plat->dvs)
-		if (pca9450_get_enable(dev)) {
-			/* If the value is already set, skip the warning. */
-			if (pca9450_get_value(dev) == uvolt)
-				return 0;
-			pr_err("Only DVS bucks can be changed when enabled\n");
-			return -EINVAL;
-		}
-
 	for (i = 0; i < plat->numranges; i++) {
 		struct pca9450_vrange *r = &plat->ranges[i];
 
-- 
2.30.2


             reply	other threads:[~2022-06-20  3:50 UTC|newest]

Thread overview: 4+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
     [not found] <CGME20220726082032epcas1p2cc28cb27c7791d8a4495325ca0abb268@epcas1p2.samsung.com>
2022-06-20  3:49 ` Heiko Thiery [this message]
2022-06-20 14:49   ` [PATCH] pmic: pca9450: permit config on all bucks and LDOs Fabio Estevam
2022-07-26  8:20   ` Jaehoon Chung
2022-08-22 10:19     ` Michael Nazzareno Trimarchi

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20220620034948.646319-1-heiko.thiery@gmail.com \
    --to=heiko.thiery@gmail.com \
    --cc=festevam@denx.de \
    --cc=jh80.chung@samsung.com \
    --cc=marex@denx.de \
    --cc=michael@amarulasolutions.com \
    --cc=u-boot@lists.denx.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox