From: Michael Trimarchi <michael@amarulasolutions.com>
To: linux-amarula@amarulasolutions.com,
Dario Binacchi <dario.binacchi@amarulasolutions.com>,
Tommaso Merciai <tommaso.merciai@amarulasolutions.com>,
Boris Brezillon <bbrezillon@kernel.org>,
Richard Weinberger <richard@nod.at>,
Patrice Chotard <patrice.chotard@foss.st.com>,
Marek Vasut <marex@denx.de>, Wolfgang Denk <wd@denx.de>,
u-boot@lists.denx.de (open list)
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>,
u-boot@lists.denx.de (open list)
Subject: [PATCH 03/11] mtd: nand: Add manufacturer specific initialization/detection steps
Date: Thu, 14 Jul 2022 16:35:35 +0200 [thread overview]
Message-ID: <20220714143543.448991-4-michael@amarulasolutions.com> (raw)
In-Reply-To: <20220714143543.448991-1-michael@amarulasolutions.com>
Upstream commit abbe26d144ec22bb067fa414d717b9f7ca2e12bd
A lot of NANDs are implementing generic features in a non-generic way,
or are providing advanced auto-detection logic where the NAND ID bytes
meaning changes with the NAND generation.
Providing this vendor specific initialization step will allow us to get
rid of full-id entries in the nand_ids table or all the vendor specific
cases added over the time in the generic NAND ID decoding logic.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
---
drivers/mtd/nand/raw/nand_base.c | 90 +++++++++++++++++++++++++-------
include/linux/mtd/rawnand.h | 30 +++++++++++
2 files changed, 102 insertions(+), 18 deletions(-)
diff --git a/drivers/mtd/nand/raw/nand_base.c b/drivers/mtd/nand/raw/nand_base.c
index 4a78770a25..3b9c78cb24 100644
--- a/drivers/mtd/nand/raw/nand_base.c
+++ b/drivers/mtd/nand/raw/nand_base.c
@@ -4286,6 +4286,39 @@ static void nand_decode_ext_id(struct mtd_info *mtd, struct nand_chip *chip)
}
}
+/*
+ * Manufacturer detection. Only used when the NAND is not ONFI or JEDEC
+ * compliant and does not have a full-id or legacy-id entry in the nand_ids
+ * table.
+ */
+static void nand_manufacturer_detect(struct mtd_info *mtd, struct nand_chip *chip)
+{
+ /*
+ * Try manufacturer detection if available and use
+ * nand_decode_ext_id() otherwise.
+ */
+ if (chip->manufacturer.desc && chip->manufacturer.desc->ops &&
+ chip->manufacturer.desc->ops->detect)
+ chip->manufacturer.desc->ops->detect(chip);
+ else
+ nand_decode_ext_id(mtd, chip);
+}
+
+/*
+ * Manufacturer initialization. This function is called for all NANDs including
+ * ONFI and JEDEC compliant ones.
+ * Manufacturer drivers should put all their specific initialization code in
+ * their ->init() hook.
+ */
+static int nand_manufacturer_init(struct nand_chip *chip)
+{
+ if (!chip->manufacturer.desc || !chip->manufacturer.desc->ops ||
+ !chip->manufacturer.desc->ops->init)
+ return 0;
+
+ return chip->manufacturer.desc->ops->init(chip);
+}
+
/*
* Old devices have chip data hardcoded in the device ID table. nand_decode_id
* decodes a matching ID table entry and assigns the MTD size parameters for
@@ -4383,6 +4416,26 @@ static bool find_full_id_nand(struct mtd_info *mtd, struct nand_chip *chip,
return false;
}
+/**
+ * nand_get_manufacturer_desc - Get manufacturer information from the
+ * manufacturer ID
+ * @id: manufacturer ID
+ *
+ * Returns a nand_manufacturer_desc object if the manufacturer is defined
+ * in the NAND manufacturers database, NULL otherwise.
+ */
+static const struct nand_manufacturers *nand_get_manufacturer_desc(u8 id)
+{
+ int i;
+
+ for (i = 0; nand_manuf_ids[i].id != 0x0; i++) {
+ if (nand_manuf_ids[i].id == id)
+ return &nand_manuf_ids[i];
+ }
+
+ return NULL;
+}
+
/*
* Get the flash and manufacturer id and lookup if the type is supported.
*/
@@ -4391,8 +4444,8 @@ struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
int *maf_id, int *dev_id,
struct nand_flash_dev *type)
{
+ const struct nand_manufacturers *manufacturer_desc;
int busw, ret;
- int maf_idx;
u8 *id_data = chip->id.data;
/*
@@ -4433,6 +4486,12 @@ struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
return ERR_PTR(-ENODEV);
}
+ chip->id.len = nand_id_len(id_data, ARRAY_SIZE(chip->id.data));
+
+ /* Try to identify manufacturer */
+ manufacturer_desc = nand_get_manufacturer_desc(*maf_id);
+ chip->manufacturer.desc = manufacturer_desc;
+
if (!type)
type = nand_flash_ids;
@@ -4451,8 +4510,6 @@ struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
*/
chip->options &= ~NAND_BUSWIDTH_16;
- chip->id.len = nand_id_len(id_data, ARRAY_SIZE(chip->id.data));
-
for (; type->name != NULL; type++) {
if (is_full_id_nand(type)) {
if (find_full_id_nand(mtd, chip, type))
@@ -4482,8 +4539,7 @@ struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
chip->chipsize = (uint64_t)type->chipsize << 20;
if (!type->pagesize) {
- /* Decode parameters from extended ID */
- nand_decode_ext_id(mtd, chip);
+ nand_manufacturer_detect(mtd, chip);
} else {
nand_decode_id(mtd, chip, type);
}
@@ -4499,12 +4555,6 @@ struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
chip->options &= ~NAND_SAMSUNG_LP_OPTIONS;
ident_done:
- /* Try to identify manufacturer */
- for (maf_idx = 0; nand_manuf_ids[maf_idx].id != 0x0; maf_idx++) {
- if (nand_manuf_ids[maf_idx].id == *maf_id)
- break;
- }
-
if (chip->options & NAND_BUSWIDTH_AUTO) {
WARN_ON(chip->options & NAND_BUSWIDTH_16);
chip->options |= busw;
@@ -4516,7 +4566,7 @@ ident_done:
*/
pr_info("device found, Manufacturer ID: 0x%02x, Chip ID: 0x%02x\n",
*maf_id, *dev_id);
- pr_info("%s %s\n", nand_manuf_ids[maf_idx].name, mtd->name);
+ pr_info("%s %s\n", manufacturer_desc->name, mtd->name);
pr_warn("bus width %d instead %d bit\n",
(chip->options & NAND_BUSWIDTH_16) ? 16 : 8,
busw ? 16 : 8);
@@ -4549,28 +4599,32 @@ ident_done:
if (mtd->writesize > 512 && chip->cmdfunc == nand_command)
chip->cmdfunc = nand_command_lp;
+ ret = nand_manufacturer_init(chip);
+ if (ret)
+ return ERR_PTR(ret);
+
pr_info("device found, Manufacturer ID: 0x%02x, Chip ID: 0x%02x\n",
*maf_id, *dev_id);
#ifdef CONFIG_SYS_NAND_ONFI_DETECTION
if (chip->onfi_version)
- pr_info("%s %s\n", nand_manuf_ids[maf_idx].name,
+ pr_info("%s %s\n", manufacturer_desc->name,
chip->onfi_params.model);
else if (chip->jedec_version)
- pr_info("%s %s\n", nand_manuf_ids[maf_idx].name,
+ pr_info("%s %s\n", manufacturer_desc->name,
chip->jedec_params.model);
else
- pr_info("%s %s\n", nand_manuf_ids[maf_idx].name,
+ pr_info("%s %s\n", manufacturer_desc->name,
type->name);
#else
if (chip->jedec_version)
- pr_info("%s %s\n", nand_manuf_ids[maf_idx].name,
+ pr_info("%s %s\n", manufacturer_desc->name,
chip->jedec_params.model);
else
- pr_info("%s %s\n", nand_manuf_ids[maf_idx].name,
+ pr_info("%s %s\n", manufacturer_desc->name,
type->name);
- pr_info("%s %s\n", nand_manuf_ids[maf_idx].name,
+ pr_info("%s %s\n", manufacturer_desc->name,
type->name);
#endif
diff --git a/include/linux/mtd/rawnand.h b/include/linux/mtd/rawnand.h
index f2c6a978cb..57fe7fb47b 100644
--- a/include/linux/mtd/rawnand.h
+++ b/include/linux/mtd/rawnand.h
@@ -796,6 +796,17 @@ nand_get_sdr_timings(const struct nand_data_interface *conf)
return &conf->timings.sdr;
}
+/**
+ * struct nand_manufacturer_ops - NAND Manufacturer operations
+ * @detect: detect the NAND memory organization and capabilities
+ * @init: initialize all vendor specific fields (like the ->read_retry()
+ * implementation) if any.
+ */
+struct nand_manufacturer_ops {
+ void (*detect)(struct nand_chip *chip);
+ int (*init)(struct nand_chip *chip);
+};
+
/**
* struct nand_chip - NAND Private Flash Chip Data
* @mtd: MTD device registered to the MTD framework
@@ -897,6 +908,7 @@ nand_get_sdr_timings(const struct nand_data_interface *conf)
* devices.
* @priv: [OPTIONAL] pointer to private chip data
* @write_page: [REPLACEABLE] High-level page write function
+ * @manufacturer: [INTERN] Contains manufacturer information
*/
struct nand_chip {
@@ -983,6 +995,11 @@ struct nand_chip {
struct nand_bbt_descr *badblock_pattern;
void *priv;
+
+ struct {
+ const struct nand_manufacturers *desc;
+ void *priv;
+ } manufacturer;
};
static inline void nand_set_flash_node(struct nand_chip *chip,
@@ -1016,6 +1033,17 @@ static inline void nand_set_controller_data(struct nand_chip *chip, void *priv)
chip->priv = priv;
}
+static inline void nand_set_manufacturer_data(struct nand_chip *chip,
+ void *priv)
+{
+ chip->manufacturer.priv = priv;
+}
+
+static inline void *nand_get_manufacturer_data(struct nand_chip *chip)
+{
+ return chip->manufacturer.priv;
+}
+
/*
* NAND Flash Manufacturer ID Codes
*/
@@ -1120,10 +1148,12 @@ struct nand_flash_dev {
* struct nand_manufacturers - NAND Flash Manufacturer ID Structure
* @name: Manufacturer name
* @id: manufacturer ID code of device.
+ * @ops: manufacturer operations
*/
struct nand_manufacturers {
int id;
char *name;
+ const struct nand_manufacturer_ops *ops;
};
extern struct nand_flash_dev nand_flash_ids[];
--
2.34.1
next prev parent reply other threads:[~2022-07-14 14:36 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20220714143543.448991-1-michael@amarulasolutions.com>
2022-07-14 14:35 ` [PATCH 01/11] mtd: nand: Get rid of busw parameter Michael Trimarchi
2022-07-14 14:35 ` [PATCH 02/11] mtd: nand: Store nand ID in struct nand_chip Michael Trimarchi
2022-07-14 14:35 ` Michael Trimarchi [this message]
2022-07-14 14:35 ` [PATCH 04/11] mtd: nand: Get rid of mtd variable in function calls Michael Trimarchi
2022-07-14 14:35 ` [PATCH 05/11] mtd: nand: Export symbol nand_decode_ext_id Michael Trimarchi
2022-07-14 14:35 ` [PATCH 06/11] mtd: nand: Move Samsung specific init/detection logic in nand_samsung.c Michael Trimarchi
2022-07-14 14:35 ` [PATCH 07/11] mtd: nand: Move Hynix specific init/detection logic in nand_hynix.c Michael Trimarchi
2022-07-14 14:35 ` [PATCH 08/11] mtd: nand: Move Toshiba specific init/detection logic in nand_toshiba.c Michael Trimarchi
2022-07-14 14:35 ` [PATCH 09/11] mtd: nand: Move Micron specific init logic in nand_micron.c Michael Trimarchi
2022-07-14 14:35 ` [PATCH 10/11] mtd: nand: Move AMD/Spansion specific init/detection logic in nand_amd.c Michael Trimarchi
2022-07-14 14:35 ` [PATCH 11/11] mtd: nand: Move Macronix specific initialization in nand_macronix.c Michael Trimarchi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220714143543.448991-4-michael@amarulasolutions.com \
--to=michael@amarulasolutions.com \
--cc=bbrezillon@kernel.org \
--cc=boris.brezillon@free-electrons.com \
--cc=dario.binacchi@amarulasolutions.com \
--cc=linux-amarula@amarulasolutions.com \
--cc=marex@denx.de \
--cc=patrice.chotard@foss.st.com \
--cc=richard@nod.at \
--cc=tommaso.merciai@amarulasolutions.com \
--cc=u-boot@lists.denx.de \
--cc=wd@denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox