From: Adam Ford <aford173@gmail.com>
To: u-boot@lists.denx.de
Cc: jh80.chung@samsung.com, sbabic@denx.de, festevam@gmail.com,
uboot-imx@nxp.com, Adam Ford <aford173@gmail.com>
Subject: [PATCH 1/4] configs: imx8mn_beacon: Re-align memory to standard imx8mn settings
Date: Wed, 17 Aug 2022 06:24:00 -0500 [thread overview]
Message-ID: <20220817112403.68144-1-aford173@gmail.com> (raw)
The imx8mn_beacon board does not use the same memory map as the reference
design from NXP or other imx8mn boards. As such, memory is more limited
in SPL.
Moving SPL_BSS_START_ADDR and SPL_STACK to default locations increases
the amount of available meory for the SPL stack. Doing this allows
the board to no longer define CONFIG_MALLOC_F_ADDR.
Since SYS_LOAD_ADDR also does not align with other boards, move it too.
Signed-off-by: Adam Ford <aford173@gmail.com>
---
Depends on
https://patchwork.ozlabs.org/project/uboot/list/?series=312020
https://patchwork.ozlabs.org/project/uboot/list/?series=312016
https://patchwork.ozlabs.org/project/uboot/list/?series=312002
diff --git a/configs/imx8mn_beacon_2g_defconfig b/configs/imx8mn_beacon_2g_defconfig
index bd17788768..98a75d4950 100644
--- a/configs/imx8mn_beacon_2g_defconfig
+++ b/configs/imx8mn_beacon_2g_defconfig
@@ -15,10 +15,9 @@ CONFIG_TARGET_IMX8MN_BEACON=y
CONFIG_IMX8MN_BEACON_2GB_LPDDR=y
CONFIG_SPL_SERIAL=y
CONFIG_SPL_DRIVERS_MISC=y
-CONFIG_SPL_SYS_MALLOC_F_LEN=0x2000
CONFIG_SPL=y
CONFIG_SPL_IMX_ROMAPI_LOADADDR=0x48000000
-CONFIG_SYS_LOAD_ADDR=0x40480000
+CONFIG_SYS_LOAD_ADDR=0x42000000
CONFIG_SYS_MEMTEST_START=0x40000000
CONFIG_SYS_MEMTEST_END=0x44000000
CONFIG_LTO=y
@@ -34,12 +33,12 @@ CONFIG_DEFAULT_FDT_FILE="imx8mn-beacon-kit.dtb"
CONFIG_ARCH_MISC_INIT=y
CONFIG_SPL_MAX_SIZE=0x25000
CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x95e000
+CONFIG_SPL_BSS_START_ADDR=0x950000
CONFIG_SPL_BSS_MAX_SIZE=0x2000
CONFIG_SPL_BOARD_INIT=y
CONFIG_SPL_BOOTROM_SUPPORT=y
# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x187ff0
+CONFIG_SPL_STACK=0x980000
CONFIG_SYS_SPL_MALLOC=y
CONFIG_HAS_CUSTOM_SPL_MALLOC_START=y
CONFIG_CUSTOM_SYS_SPL_MALLOC_ADDR=0x42200000
diff --git a/configs/imx8mn_beacon_defconfig b/configs/imx8mn_beacon_defconfig
index 738d308f45..271578985f 100644
--- a/configs/imx8mn_beacon_defconfig
+++ b/configs/imx8mn_beacon_defconfig
@@ -14,10 +14,9 @@ CONFIG_SPL_TEXT_BASE=0x912000
CONFIG_TARGET_IMX8MN_BEACON=y
CONFIG_SPL_SERIAL=y
CONFIG_SPL_DRIVERS_MISC=y
-CONFIG_SPL_SYS_MALLOC_F_LEN=0x2000
CONFIG_SPL=y
CONFIG_SPL_IMX_ROMAPI_LOADADDR=0x48000000
-CONFIG_SYS_LOAD_ADDR=0x40480000
+CONFIG_SYS_LOAD_ADDR=0x42000000
CONFIG_SYS_MEMTEST_START=0x40000000
CONFIG_SYS_MEMTEST_END=0x44000000
CONFIG_LTO=y
@@ -33,12 +32,12 @@ CONFIG_DEFAULT_FDT_FILE="imx8mn-beacon-kit.dtb"
CONFIG_ARCH_MISC_INIT=y
CONFIG_SPL_MAX_SIZE=0x25000
CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x95e000
+CONFIG_SPL_BSS_START_ADDR=0x950000
CONFIG_SPL_BSS_MAX_SIZE=0x2000
CONFIG_SPL_BOARD_INIT=y
CONFIG_SPL_BOOTROM_SUPPORT=y
# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x187ff0
+CONFIG_SPL_STACK=0x980000
CONFIG_SYS_SPL_MALLOC=y
CONFIG_HAS_CUSTOM_SPL_MALLOC_START=y
CONFIG_CUSTOM_SYS_SPL_MALLOC_ADDR=0x42200000
diff --git a/configs/imx8mn_beacon_fspi_defconfig b/configs/imx8mn_beacon_fspi_defconfig
index ecaefd8930..6da2182eb3 100644
--- a/configs/imx8mn_beacon_fspi_defconfig
+++ b/configs/imx8mn_beacon_fspi_defconfig
@@ -14,10 +14,9 @@ CONFIG_SPL_TEXT_BASE=0x912000
CONFIG_TARGET_IMX8MN_BEACON=y
CONFIG_SPL_SERIAL=y
CONFIG_SPL_DRIVERS_MISC=y
-CONFIG_SPL_SYS_MALLOC_F_LEN=0x2000
CONFIG_SPL=y
CONFIG_SPL_IMX_ROMAPI_LOADADDR=0x48000000
-CONFIG_SYS_LOAD_ADDR=0x40480000
+CONFIG_SYS_LOAD_ADDR=0x42000000
CONFIG_SYS_MEMTEST_START=0x40000000
CONFIG_SYS_MEMTEST_END=0x44000000
CONFIG_LTO=y
@@ -33,12 +32,12 @@ CONFIG_DEFAULT_FDT_FILE="imx8mn-beacon-kit.dtb"
CONFIG_ARCH_MISC_INIT=y
CONFIG_SPL_MAX_SIZE=0x25000
CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x95e000
+CONFIG_SPL_BSS_START_ADDR=0x950000
CONFIG_SPL_BSS_MAX_SIZE=0x2000
CONFIG_SPL_BOARD_INIT=y
CONFIG_SPL_BOOTROM_SUPPORT=y
# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SPL_STACK=0x187ff0
+CONFIG_SPL_STACK=0x980000
CONFIG_SYS_SPL_MALLOC=y
CONFIG_HAS_CUSTOM_SPL_MALLOC_START=y
CONFIG_CUSTOM_SYS_SPL_MALLOC_ADDR=0x42200000
diff --git a/include/configs/imx8mn_beacon.h b/include/configs/imx8mn_beacon.h
index 6faecbde77..930b11b75e 100644
--- a/include/configs/imx8mn_beacon.h
+++ b/include/configs/imx8mn_beacon.h
@@ -13,14 +13,6 @@
#define CONFIG_SYS_UBOOT_BASE \
(QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)
-#ifdef CONFIG_SPL_BUILD
-/* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
-#define CONFIG_MALLOC_F_ADDR 0x184000
-
-/* For RAW image gives a error info not panic */
-
-#endif /* CONFIG_SPL_BUILD */
-
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS \
"script=boot.scr\0" \
--
2.34.1
next reply other threads:[~2022-08-17 11:24 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-08-17 11:24 Adam Ford [this message]
2022-08-17 11:24 ` [PATCH 2/4] regulator: bd718x7: Only bind children when PMIC_CHILDREN is enabled Adam Ford
2022-08-17 18:53 ` Simon Glass
2022-08-17 11:24 ` [PATCH 3/4] configs: imx8mn_beacon: Enable SPL_DM_PMIC_BD71837 Adam Ford
2022-08-17 11:24 ` [PATCH 4/4] imx: imx8mn-beacon: Configure PMIC before DDR initialization Adam Ford
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220817112403.68144-1-aford173@gmail.com \
--to=aford173@gmail.com \
--cc=festevam@gmail.com \
--cc=jh80.chung@samsung.com \
--cc=sbabic@denx.de \
--cc=u-boot@lists.denx.de \
--cc=uboot-imx@nxp.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox