[PATCH v1 2/5] net: dwc_eth_qos: Add StarFive ethernet driver glue layer

[Yanhong Wang <yanhong.wang@starfivetech.com>]

The StarFive ETHQOS hardware has its own clock and reset,so add a
corresponding glue driver to configure them.

Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
---
 drivers/net/Kconfig                |   7 +
 drivers/net/Makefile               |   1 +
 drivers/net/dwc_eth_qos.c          |   6 +
 drivers/net/dwc_eth_qos.h          |   2 +
 drivers/net/dwc_eth_qos_starfive.c | 306 +++++++++++++++++++++++++++++
 5 files changed, 322 insertions(+)
 create mode 100644 drivers/net/dwc_eth_qos_starfive.c

diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index ceadee98a1..161289d00f 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -249,6 +249,13 @@ config DWC_ETH_QOS_QCOM
 	  The Synopsys Designware Ethernet QOS IP block with specific
 	  configuration used in Qcom QCS404 SoC.
 
+config DWC_ETH_QOS_STARFIVE
+	bool "Synopsys DWC Ethernet QOS device support for STARFIVE"
+	depends on DWC_ETH_QOS
+	help
+	  The Synopsys Designware Ethernet QOS IP block with specific
+	  configuration used in STARFIVE  JH7110 soc.
+
 config E1000
 	bool "Intel PRO/1000 Gigabit Ethernet support"
 	depends on PCI
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 75daa5e694..69af678757 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -21,6 +21,7 @@ obj-$(CONFIG_DSA_SANDBOX) += dsa_sandbox.o
 obj-$(CONFIG_DWC_ETH_QOS) += dwc_eth_qos.o
 obj-$(CONFIG_DWC_ETH_QOS_IMX) += dwc_eth_qos_imx.o
 obj-$(CONFIG_DWC_ETH_QOS_QCOM) += dwc_eth_qos_qcom.o
+obj-$(CONFIG_DWC_ETH_QOS_STARFIVE) += dwc_eth_qos_starfive.o
 obj-$(CONFIG_E1000) += e1000.o
 obj-$(CONFIG_E1000_SPI) += e1000_spi.o
 obj-$(CONFIG_EEPRO100) += eepro100.o
diff --git a/drivers/net/dwc_eth_qos.c b/drivers/net/dwc_eth_qos.c
index 112deb546d..9aecd56e73 100644
--- a/drivers/net/dwc_eth_qos.c
+++ b/drivers/net/dwc_eth_qos.c
@@ -1718,6 +1718,12 @@ static const struct udevice_id eqos_ids[] = {
 		.data = (ulong)&eqos_qcom_config
 	},
 #endif
+#if IS_ENABLED(CONFIG_DWC_ETH_QOS_STARFIVE)
+	{
+		.compatible = "starfive,jh7110-dwmac",
+		.data = (ulong)&eqos_jh7110_config
+	},
+#endif
 
 	{ }
 };
diff --git a/drivers/net/dwc_eth_qos.h b/drivers/net/dwc_eth_qos.h
index fddbe9336c..20450497a9 100644
--- a/drivers/net/dwc_eth_qos.h
+++ b/drivers/net/dwc_eth_qos.h
@@ -279,6 +279,7 @@ struct eqos_priv {
 	bool clk_ck_enabled;
 	unsigned int tx_fifo_sz, rx_fifo_sz;
 	u32 reset_delays[3];
+	struct reset_ctl reset_ahb;
 };
 
 void eqos_inval_desc_generic(void *desc);
@@ -289,3 +290,4 @@ int eqos_null_ops(struct udevice *dev);
 
 extern struct eqos_config eqos_imx_config;
 extern struct eqos_config eqos_qcom_config;
+extern struct eqos_config eqos_jh7110_config;
diff --git a/drivers/net/dwc_eth_qos_starfive.c b/drivers/net/dwc_eth_qos_starfive.c
new file mode 100644
index 0000000000..eeb45981bd
--- /dev/null
+++ b/drivers/net/dwc_eth_qos_starfive.c
@@ -0,0 +1,306 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2023 StarFive Technology Co., Ltd.
+ * Author: Yanhong Wang<yanhong.wang@starfivetech.com>
+ */
+
+#include <common.h>
+#include <asm/cache.h>
+#include <asm/gpio.h>
+#include <clk.h>
+#include <dm.h>
+#include <eth_phy.h>
+#include <regmap.h>
+#include <reset.h>
+#include <syscon.h>
+
+#include "dwc_eth_qos.h"
+
+#define STARFIVE_DWMAC_PHY_INFT_RGMII	0x1
+#define STARFIVE_DWMAC_PHY_INFT_RMII	0x4
+#define STARFIVE_DWMAC_PHY_INFT_FIELD	0x7U
+
+static int eqos_interface_init_jh7110(struct udevice *dev,
+				      phy_interface_t interface_type)
+{
+	struct regmap *regmap;
+	struct ofnode_phandle_args args;
+	unsigned int mode;
+	int ret;
+
+	switch (interface_type) {
+	case PHY_INTERFACE_MODE_RMII:
+		mode = STARFIVE_DWMAC_PHY_INFT_RMII;
+		break;
+
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+		mode = STARFIVE_DWMAC_PHY_INFT_RGMII;
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	ret = dev_read_phandle_with_args(dev, "starfive,syscon", NULL,
+					 2, 0, &args);
+	if (ret)
+		return ret;
+
+	if (args.args_count != 2)
+		return -EINVAL;
+
+	regmap = syscon_regmap_lookup_by_phandle(dev, "starfive,syscon");
+	if (IS_ERR(regmap)) {
+		ret = PTR_ERR(regmap);
+		pr_err("Failed to get regmap: %d\n", ret);
+		return ret;
+	}
+
+	return regmap_update_bits(regmap, args.args[0],
+				  STARFIVE_DWMAC_PHY_INFT_FIELD << args.args[1],
+				  mode << args.args[1]);
+}
+
+static int eqos_set_tx_clk_speed_jh7110(struct udevice *dev)
+{
+	struct eqos_priv *eqos = dev_get_priv(dev);
+	struct clk *pclk, *c;
+	ulong rate;
+	int ret;
+
+	/* Generally, the rgmii_tx clock is provided by the internal clock,
+	 * which needs to match the corresponding clock frequency according
+	 * to different speeds. If the rgmii_tx clock is provided by the
+	 * external rgmii_rxin, there is no need to configure the clock
+	 * internally, because rgmii_rxin will be adaptively adjusted.
+	 */
+	if (dev_read_bool(dev, "starfive,tx-use-rgmii-clk"))
+		return 0;
+
+	switch (eqos->phy->speed) {
+	case SPEED_1000:
+		rate = 125 * 1000 * 1000;
+		break;
+	case SPEED_100:
+		rate = 25 * 1000 * 1000;
+		break;
+	case SPEED_10:
+		rate = 2.5 * 1000 * 1000;
+		break;
+	default:
+		pr_err("invalid speed %d", eqos->phy->speed);
+		return -EINVAL;
+	}
+
+	/* eqos->clk_tx clock has no set rate operation, so just set the parent
+	 * clock rate directly
+	 */
+	ret = clk_get_by_id(eqos->clk_tx.id, &c);
+	if (ret)
+		return ret;
+
+	pclk = clk_get_parent(c);
+	if (pclk) {
+		ret = clk_set_rate(pclk, rate);
+		if (ret < 0) {
+			pr_err("jh7110 (clk_tx, %lu) failed: %d", rate, ret);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static ulong eqos_get_tick_clk_rate_jh7110(struct udevice *dev)
+{
+	struct eqos_priv *eqos = dev_get_priv(dev);
+
+	return clk_get_rate(&eqos->clk_tx);
+}
+
+static int eqos_start_clks_jh7110(struct udevice *dev)
+{
+	struct eqos_priv *eqos = dev_get_priv(dev);
+	int ret;
+
+	ret = clk_enable(&eqos->clk_slave_bus);
+	if (ret < 0)
+		goto err;
+
+	ret = clk_enable(&eqos->clk_master_bus);
+	if (ret < 0)
+		goto err_disable_clk_slave_bus;
+
+	ret = clk_enable(&eqos->clk_ptp_ref);
+	if (ret < 0)
+		goto err_disable_clk_master_bus;
+
+	ret = clk_enable(&eqos->clk_tx);
+	if (ret < 0)
+		goto err_disable_clk_ptp_ref;
+
+	ret = clk_enable(&eqos->clk_ck);
+	if (ret < 0)
+		goto err_disable_clk_tx;
+
+	return 0;
+
+err_disable_clk_tx:
+	clk_disable(&eqos->clk_tx);
+err_disable_clk_ptp_ref:
+	clk_disable(&eqos->clk_ptp_ref);
+err_disable_clk_master_bus:
+	clk_disable(&eqos->clk_master_bus);
+err_disable_clk_slave_bus:
+	clk_disable(&eqos->clk_slave_bus);
+err:
+	debug("%s: FAILED: %d\n", __func__, ret);
+
+	return ret;
+}
+
+static int eqos_stop_clks_jh7110(struct udevice *dev)
+{
+	struct eqos_priv *eqos = dev_get_priv(dev);
+
+	clk_disable(&eqos->clk_ck);
+	clk_disable(&eqos->clk_tx);
+	clk_disable(&eqos->clk_ptp_ref);
+	clk_disable(&eqos->clk_master_bus);
+	clk_disable(&eqos->clk_slave_bus);
+
+	return 0;
+}
+
+static int eqos_start_resets_jh7110(struct udevice *dev)
+{
+	struct eqos_priv *eqos = dev_get_priv(dev);
+	int ret;
+
+	ret = reset_deassert(&eqos->reset_ctl);
+	if (ret < 0)
+		return ret;
+
+	ret = reset_deassert(&eqos->reset_ahb);
+	if (ret < 0)
+		goto err_free_reset_ctl;
+
+	return 0;
+
+err_free_reset_ctl:
+	reset_assert(&eqos->reset_ctl);
+	return ret;
+}
+
+static int eqos_stop_resets_jh7110(struct udevice *dev)
+{
+	struct eqos_priv *eqos = dev_get_priv(dev);
+
+	reset_assert(&eqos->reset_ctl);
+	reset_assert(&eqos->reset_ahb);
+
+	return 0;
+}
+
+static int eqos_remove_resources_jh7110(struct udevice *dev)
+{
+	struct eqos_priv *eqos = dev_get_priv(dev);
+
+	clk_free(&eqos->clk_tx);
+	clk_free(&eqos->clk_ck);
+	clk_free(&eqos->clk_slave_bus);
+	clk_free(&eqos->clk_master_bus);
+	reset_free(&eqos->reset_ahb);
+	reset_free(&eqos->reset_ctl);
+
+	return 0;
+}
+
+static int eqos_probe_resources_jh7110(struct udevice *dev)
+{
+	struct eqos_priv *eqos = dev_get_priv(dev);
+	phy_interface_t interface;
+	int ret;
+
+	interface = eqos->config->interface(dev);
+
+	if (interface == PHY_INTERFACE_MODE_NA) {
+		pr_err("Invalid PHY interface\n");
+		return -EINVAL;
+	}
+
+	ret = reset_get_by_name(dev, "stmmaceth", &eqos->reset_ctl);
+	if (ret)
+		return ret;
+
+	ret = reset_get_by_name(dev, "ahb", &eqos->reset_ahb);
+	if (ret)
+		goto err_free_reset_stmmaceth;
+
+	ret = clk_get_by_name(dev, "stmmaceth", &eqos->clk_master_bus);
+	if (ret)
+		goto err_free_reset_ahb;
+
+	ret = clk_get_by_name(dev, "pclk", &eqos->clk_slave_bus);
+	if (ret)
+		goto err_free_clk_stmmaceth;
+
+	ret = clk_get_by_name(dev, "ptp_ref", &eqos->clk_ptp_ref);
+	if (ret)
+		goto err_free_clk_pclk;
+
+	ret = clk_get_by_name(dev, "tx", &eqos->clk_ck);
+	if (ret)
+		goto err_free_clk_ptp_ref;
+
+	ret = clk_get_by_name(dev, "gtx", &eqos->clk_tx);
+	if (ret)
+		goto err_free_clk_tx;
+
+	return eqos_interface_init_jh7110(dev, interface);
+
+err_free_clk_tx:
+	clk_free(&eqos->clk_tx);
+err_free_clk_ptp_ref:
+	clk_free(&eqos->clk_ptp_ref);
+err_free_clk_pclk:
+	clk_free(&eqos->clk_slave_bus);
+err_free_clk_stmmaceth:
+	clk_free(&eqos->clk_master_bus);
+err_free_reset_ahb:
+	reset_free(&eqos->reset_ahb);
+err_free_reset_stmmaceth:
+	reset_free(&eqos->reset_ctl);
+
+	return ret;
+}
+
+static struct eqos_ops eqos_jh7110_ops = {
+	.eqos_inval_desc = eqos_inval_desc_generic,
+	.eqos_flush_desc = eqos_flush_desc_generic,
+	.eqos_inval_buffer = eqos_inval_buffer_generic,
+	.eqos_flush_buffer = eqos_flush_buffer_generic,
+	.eqos_probe_resources = eqos_probe_resources_jh7110,
+	.eqos_remove_resources = eqos_remove_resources_jh7110,
+	.eqos_stop_resets = eqos_stop_resets_jh7110,
+	.eqos_start_resets = eqos_start_resets_jh7110,
+	.eqos_stop_clks = eqos_stop_clks_jh7110,
+	.eqos_start_clks = eqos_start_clks_jh7110,
+	.eqos_calibrate_pads = eqos_null_ops,
+	.eqos_disable_calibration = eqos_null_ops,
+	.eqos_set_tx_clk_speed = eqos_set_tx_clk_speed_jh7110,
+	.eqos_get_enetaddr = eqos_null_ops,
+	.eqos_get_tick_clk_rate = eqos_get_tick_clk_rate_jh7110
+};
+
+struct eqos_config __maybe_unused eqos_jh7110_config = {
+	.reg_access_always_ok = false,
+	.mdio_wait = 10,
+	.swr_wait = 50,
+	.config_mac = EQOS_MAC_RXQ_CTRL0_RXQ0EN_ENABLED_DCB,
+	.config_mac_mdio = EQOS_MAC_MDIO_ADDRESS_CR_250_300,
+	.axi_bus_width = EQOS_AXI_WIDTH_64,
+	.interface = dev_read_phy_mode,
+	.ops = &eqos_jh7110_ops
+};
-- 
2.17.1