From: Yanhong Wang <yanhong.wang@starfivetech.com>
To: <u-boot@lists.denx.de>, Rick Chen <rick@andestech.com>,
Leo <ycliang@andestech.com>,
Joe Hershberger <joe.hershberger@ni.com>,
"Ramon Fried" <rfried.dev@gmail.com>
Cc: Yanhong Wang <yanhong.wang@starfivetech.com>
Subject: [PATCH v1 3/5] riscv: dts: jh7110: Add ethernet device tree nodes
Date: Fri, 17 Mar 2023 09:05:34 +0800 [thread overview]
Message-ID: <20230317010536.17860-4-yanhong.wang@starfivetech.com> (raw)
In-Reply-To: <20230317010536.17860-1-yanhong.wang@starfivetech.com>
Add ethernet device tree node to support StarFive ethernet driver for
the JH7110 RISC-V SoC.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
---
arch/riscv/dts/jh7110.dtsi | 69 ++++++++++++++++++++++++++++++++++++++
1 file changed, 69 insertions(+)
diff --git a/arch/riscv/dts/jh7110.dtsi b/arch/riscv/dts/jh7110.dtsi
index d3e9f92987..67267d9024 100644
--- a/arch/riscv/dts/jh7110.dtsi
+++ b/arch/riscv/dts/jh7110.dtsi
@@ -244,6 +244,13 @@
#clock-cells = <0>;
};
+ stmmac_axi_setup: stmmac-axi-config {
+ snps,lpi_en;
+ snps,wr_osr_lmt = <4>;
+ snps,rd_osr_lmt = <4>;
+ snps,blen = <256 128 64 32 0 0 0>;
+ };
+
soc {
compatible = "simple-bus";
interrupt-parent = <&plic>;
@@ -548,6 +555,68 @@
status = "disabled";
};
+ gmac0: ethernet@16030000 {
+ compatible = "starfive,jh7110-dwmac", "snps,dwmac-5.20";
+ reg = <0x0 0x16030000 0x0 0x10000>;
+ clocks = <&aoncrg JH7110_AONCLK_GMAC0_AXI>,
+ <&aoncrg JH7110_AONCLK_GMAC0_AHB>,
+ <&syscrg JH7110_SYSCLK_GMAC0_PTP>,
+ <&aoncrg JH7110_AONCLK_GMAC0_TX_INV>,
+ <&syscrg JH7110_SYSCLK_GMAC0_GTXC>;
+ clock-names = "stmmaceth", "pclk", "ptp_ref",
+ "tx", "gtx";
+ resets = <&aoncrg JH7110_AONRST_GMAC0_AXI>,
+ <&aoncrg JH7110_AONRST_GMAC0_AHB>;
+ reset-names = "stmmaceth", "ahb";
+ interrupts = <7>, <6>, <5>;
+ interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+ snps,multicast-filter-bins = <64>;
+ snps,perfect-filter-entries = <8>;
+ rx-fifo-depth = <2048>;
+ tx-fifo-depth = <2048>;
+ snps,fixed-burst;
+ snps,no-pbl-x8;
+ snps,force_thresh_dma_mode;
+ snps,axi-config = <&stmmac_axi_setup>;
+ snps,tso;
+ snps,en-tx-lpi-clockgating;
+ snps,txpbl = <16>;
+ snps,rxpbl = <16>;
+ starfive,syscon = <&aon_syscon 0xc 0x12>;
+ status = "disabled";
+ };
+
+ gmac1: ethernet@16040000 {
+ compatible = "starfive,jh7110-dwmac", "snps,dwmac-5.20";
+ reg = <0x0 0x16040000 0x0 0x10000>;
+ clocks = <&syscrg JH7110_SYSCLK_GMAC1_AXI>,
+ <&syscrg JH7110_SYSCLK_GMAC1_AHB>,
+ <&syscrg JH7110_SYSCLK_GMAC1_PTP>,
+ <&syscrg JH7110_SYSCLK_GMAC1_TX_INV>,
+ <&syscrg JH7110_SYSCLK_GMAC1_GTXC>;
+ clock-names = "stmmaceth", "pclk", "ptp_ref",
+ "tx", "gtx";
+ resets = <&syscrg JH7110_SYSRST_GMAC1_AXI>,
+ <&syscrg JH7110_SYSRST_GMAC1_AHB>;
+ reset-names = "stmmaceth", "ahb";
+ interrupts = <78>, <77>, <76>;
+ interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+ snps,multicast-filter-bins = <64>;
+ snps,perfect-filter-entries = <8>;
+ rx-fifo-depth = <2048>;
+ tx-fifo-depth = <2048>;
+ snps,fixed-burst;
+ snps,no-pbl-x8;
+ snps,force_thresh_dma_mode;
+ snps,axi-config = <&stmmac_axi_setup>;
+ snps,tso;
+ snps,en-tx-lpi-clockgating;
+ snps,txpbl = <16>;
+ snps,rxpbl = <16>;
+ starfive,syscon = <&sys_syscon 0x90 0x2>;
+ status = "disabled";
+ };
+
aoncrg: clock-controller@17000000 {
compatible = "starfive,jh7110-aoncrg";
reg = <0x0 0x17000000 0x0 0x10000>;
--
2.17.1
next prev parent reply other threads:[~2023-03-17 1:05 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-03-17 1:05 [PATCH v1 0/5] Add Ethernet driver for StarFive JH7110 SoC Yanhong Wang
2023-03-17 1:05 ` [PATCH v1 1/5] net: phy: Add driver for Motorcomm yt8531 gigabit ethernet phy Yanhong Wang
2023-03-18 20:20 ` Simon Glass
2023-03-20 2:53 ` yanhong wang
2023-03-24 8:21 ` yanhong wang
2023-03-17 1:05 ` [PATCH v1 2/5] net: dwc_eth_qos: Add StarFive ethernet driver glue layer Yanhong Wang
2023-03-18 20:20 ` Simon Glass
2023-03-20 3:30 ` yanhong wang
2023-03-17 1:05 ` Yanhong Wang [this message]
2023-03-17 1:05 ` [PATCH v1 4/5] riscv: dts: starfive: Add phy clock delay configuration for StarFive VisionFive2 board Yanhong Wang
2023-03-17 1:05 ` [PATCH v1 5/5] configs: starfive: Enable ethernet configuration for StarFive VisionFive 2 Yanhong Wang
2023-03-24 12:53 ` [PATCH v1 0/5] Add Ethernet driver for StarFive JH7110 SoC Torsten Duwe
2023-03-27 2:22 ` yanhong wang
2023-03-27 8:09 ` Torsten Duwe
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230317010536.17860-4-yanhong.wang@starfivetech.com \
--to=yanhong.wang@starfivetech.com \
--cc=joe.hershberger@ni.com \
--cc=rfried.dev@gmail.com \
--cc=rick@andestech.com \
--cc=u-boot@lists.denx.de \
--cc=ycliang@andestech.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox