[v1 1/2] board: mediatek: add Bananapi-R3 devicetree

[Frank Wunderlich <linux@fw-web.de>]

From: Daniel Golle <daniel@makrotopia.org>

Add board specific devicetree for Bananapi R3 SBC.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
---
taken from openwrt
https://git.openwrt.org/?p=openwrt/openwrt.git;a=blob;f=package/boot/uboot-mediatek/patches/430-add-bpi-r3.patch;hb=HEAD
only enabled the factory button which was disabled because a HW-bug in
rev 1.0 of r3.
---
 arch/arm/dts/Makefile                |   2 +
 arch/arm/dts/mt7986a-bpi-r3-emmc.dts |  32 ++++
 arch/arm/dts/mt7986a-bpi-r3-sd.dts   | 268 +++++++++++++++++++++++++++
 3 files changed, 302 insertions(+)
 create mode 100644 arch/arm/dts/mt7986a-bpi-r3-emmc.dts
 create mode 100644 arch/arm/dts/mt7986a-bpi-r3-sd.dts

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 0a9b1f7749d5..de0c0e35b8c3 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -1296,6 +1296,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
 	mt7981-rfb.dtb \
 	mt7981-emmc-rfb.dtb \
 	mt7981-sd-rfb.dtb \
+	mt7986a-bpi-r3-sd.dtb \
+	mt7986a-bpi-r3-emmc.dtb \
 	mt7986a-rfb.dtb \
 	mt7986b-rfb.dtb \
 	mt7986a-sd-rfb.dtb \
diff --git a/arch/arm/dts/mt7986a-bpi-r3-emmc.dts b/arch/arm/dts/mt7986a-bpi-r3-emmc.dts
new file mode 100644
index 000000000000..4e2e5262f536
--- /dev/null
+++ b/arch/arm/dts/mt7986a-bpi-r3-emmc.dts
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2021 MediaTek Inc.
+ * Author: Sam Shih <sam.shih@mediatek.com>
+ */
+
+/dts-v1/;
+#include "mt7986a-bpi-r3-sd.dts"
+#include <dt-bindings/gpio/gpio.h>
+/ {
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_default>;
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	cap-mmc-highspeed;
+	cap-mmc-hw-reset;
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	non-removable;
+	status = "okay";
+};
diff --git a/arch/arm/dts/mt7986a-bpi-r3-sd.dts b/arch/arm/dts/mt7986a-bpi-r3-sd.dts
new file mode 100644
index 000000000000..82a3975c7de8
--- /dev/null
+++ b/arch/arm/dts/mt7986a-bpi-r3-sd.dts
@@ -0,0 +1,268 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2021 MediaTek Inc.
+ * Author: Sam Shih <sam.shih@mediatek.com>
+ */
+
+/dts-v1/;
+#include "mt7986.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "BananaPi BPi-R3";
+	compatible = "mediatek,mt7986", "mediatek,mt7986-sd-rfb";
+
+	chosen {
+		stdout-path = &uart0;
+		tick-timer = &timer0;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		factory {
+			label = "reset";
+			gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
+		};
+
+		wps {
+			label = "reset";
+			gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_status_green: green {
+			label = "green:status";
+			gpios = <&gpio 69 GPIO_ACTIVE_HIGH>;
+		};
+
+		led_status_blue: blue {
+			label = "blue:status";
+			gpios = <&gpio 86 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "disabled";
+};
+
+&eth {
+	status = "okay";
+	mediatek,gmac-id = <0>;
+	phy-mode = "sgmii";
+	mediatek,switch = "mt7531";
+	reset-gpios = <&gpio 5 GPIO_ACTIVE_HIGH>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&pinctrl {
+	spic_pins: spi1-pins-func-1 {
+		mux {
+			function = "spi";
+			groups = "spi1_2";
+		};
+	};
+
+	uart1_pins: spi1-pins-func-3 {
+		mux {
+			function = "uart";
+			groups = "uart1_2";
+		};
+	};
+
+	pwm_pins: pwm0-pins-func-1 {
+		mux {
+			function = "pwm";
+			groups = "pwm0";
+		};
+	};
+
+	mmc0_pins_default: mmc0default {
+		mux {
+			function = "flash";
+			groups =  "emmc_51";
+		};
+
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <MTK_DRIVE_4mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <MTK_DRIVE_6mA>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		conf-dsl {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <MTK_DRIVE_4mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+	};
+
+	spi_flash_pins: spi0-pins-func-1 {
+		mux {
+			function = "flash";
+			groups = "spi0", "spi0_wp_hold";
+		};
+
+		conf-pu {
+			pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_00>;
+		};
+
+		conf-pd {
+			pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_00>;
+		};
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm_pins>;
+	status = "okay";
+};
+
+&spi0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi_flash_pins>;
+	status = "okay";
+	must_tx;
+	enhance_timing;
+	dma_ext;
+	ipm_design;
+	support_quad;
+	tick_dly = <1>;
+	sample_sel = <0>;
+
+	spi_nor@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <52000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "bl2";
+				reg = <0x0 0x40000>;
+			};
+
+			partition@40000 {
+				label = "u-boot-env";
+				reg = <0x40000 0x40000>;
+			};
+
+			partition@80000 {
+				label = "reserved";
+				reg = <0x80000 0x80000>;
+			};
+
+			partition@100000 {
+				label = "fip";
+				reg = <0x100000 0x80000>;
+			};
+
+			partition@180000 {
+				label = "recovery";
+				reg = <0x180000 0xa80000>;
+			};
+
+			partition@c00000 {
+				label = "fit";
+				reg = <0xc00000 0x1400000>;
+			};
+		};
+	};
+
+	spi_nand@1 {
+		compatible = "spi-nand";
+		reg = <1>;
+		spi-max-frequency = <52000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "bl2";
+				reg = <0x0 0x80000>;
+			};
+
+			partition@80000 {
+				label = "factory";
+				reg = <0x80000 0x300000>;
+			};
+
+			partition@380000 {
+				label = "fip";
+				reg = <0x380000 0x200000>;
+			};
+
+			partition@580000 {
+				label = "ubi";
+				reg = <0x580000 0x7a80000>;
+			};
+		};
+	};
+};
+
+&watchdog {
+	status = "disabled";
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_default>;
+	bus-width = <4>;
+	max-frequency = <52000000>;
+	cap-sd-highspeed;
+	r_smpl = <1>;
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
-- 
2.34.1