From: Nishanth Menon <nm@ti.com>
To: Simon Glass <sjg@chromium.org>, Roger Quadros <rogerq@kernel.org>,
Nishanth Menon <nm@ti.com>, Vignesh Raghavendra <vigneshr@ti.com>,
Tom Rini <trini@konsulko.com>
Cc: Neil Armstrong <neil.armstrong@linaro.org>,
Anand Gadiyar <gadiyar@ti.com>, Georgi Vlaev <g-vlaev@ti.com>,
<u-boot@lists.denx.de>, "Neha Malcom Francis" <n-francis@ti.com>,
Nikhil M Jain <n-jain1@ti.com>
Subject: [PATCH 12/23] arm: dts: k3-am642-r5-sk: Use am642-sk.dts and k3-am642-sk-u-boot.dtsi
Date: Fri, 14 Apr 2023 02:57:15 -0500 [thread overview]
Message-ID: <20230414075726.387461-13-nm@ti.com> (raw)
In-Reply-To: <20230414075726.387461-1-nm@ti.com>
Use am642-sk.dts to represent the Board and selectively enable/override
the configurations necessary. And since am642-sk-u-boot.dtsi also needs
to setup common properties, instead of re-inventing everything, just
reuse the definitions.
Signed-off-by: Nishanth Menon <nm@ti.com>
---
arch/arm/dts/k3-am642-r5-sk.dts | 194 +++-----------------------------
1 file changed, 18 insertions(+), 176 deletions(-)
diff --git a/arch/arm/dts/k3-am642-r5-sk.dts b/arch/arm/dts/k3-am642-r5-sk.dts
index 9ff4dd3dd365..8ac6cc77256c 100644
--- a/arch/arm/dts/k3-am642-r5-sk.dts
+++ b/arch/arm/dts/k3-am642-r5-sk.dts
@@ -5,31 +5,18 @@
/dts-v1/;
-#include <dt-bindings/mux/ti-serdes.h>
-#include <dt-bindings/phy/phy.h>
-#include <dt-bindings/net/ti-dp83867.h>
-#include "k3-am642.dtsi"
+#include "k3-am642-sk.dts"
#include "k3-am64-sk-lp4-1600MTs.dtsi"
#include "k3-am64-ddr.dtsi"
-/ {
- chosen {
- stdout-path = "serial2:115200n8";
- tick-timer = &timer1;
- };
+#include "k3-am642-sk-u-boot.dtsi"
+/ {
aliases {
remoteproc0 = &sysctrler;
remoteproc1 = &a53_0;
};
- memory@80000000 {
- device_type = "memory";
- /* 2G RAM */
- reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
- bootph-pre-ram;
- };
-
a53_0: a53@0 {
compatible = "ti,am654-rproc";
reg = <0x00 0x00a90000 0x00 0x10>;
@@ -46,18 +33,6 @@
bootph-pre-ram;
};
- reserved-memory {
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- secure_ddr: optee@9e800000 {
- reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */
- alignment = <0x1000>;
- no-map;
- };
- };
-
clk_200mhz: dummy-clock-200mhz {
compatible = "fixed-clock";
#clock-cells = <0>;
@@ -73,9 +48,8 @@
mbox-names = "tx", "rx";
bootph-pre-ram;
};
-};
-&cbass_main {
+ /* XXX: Upstream kernel TODO: send upstream */
main_esm: esm@420000 {
compatible = "ti,j721e-esm";
reg = <0x0 0x420000 0x0 0x1000>;
@@ -86,6 +60,8 @@
&cbass_mcu {
bootph-pre-ram;
+
+ /* XXX: Upstream kernel TODO: send upstream */
mcu_esm: esm@4100000 {
compatible = "ti,j721e-esm";
reg = <0x0 0x4100000 0x0 0x1000>;
@@ -94,92 +70,8 @@
};
};
-&main_pmx0 {
- bootph-pre-ram;
- main_uart0_pins_default: main-uart0-pins-default {
- bootph-pre-ram;
- pinctrl-single,pins = <
- AM64X_IOPAD(0x0238, PIN_INPUT, 0) /* (B16) UART0_CTSn */
- AM64X_IOPAD(0x023c, PIN_OUTPUT, 0) /* (A16) UART0_RTSn */
- AM64X_IOPAD(0x0230, PIN_INPUT, 0) /* (D15) UART0_RXD */
- AM64X_IOPAD(0x0234, PIN_OUTPUT, 0) /* (C16) UART0_TXD */
- >;
- };
-
- main_uart1_pins_default: main-uart1-pins-default {
- bootph-pre-ram;
- pinctrl-single,pins = <
- AM64X_IOPAD(0x0248, PIN_INPUT, 0) /* (D16) UART1_CTSn */
- AM64X_IOPAD(0x024c, PIN_OUTPUT, 0) /* (E16) UART1_RTSn */
- AM64X_IOPAD(0x0240, PIN_INPUT, 0) /* (E15) UART1_RXD */
- AM64X_IOPAD(0x0244, PIN_OUTPUT, 0) /* (E14) UART1_TXD */
- >;
- };
-
- main_mmc1_pins_default: main-mmc1-pins-default {
- bootph-pre-ram;
- pinctrl-single,pins = <
- AM64X_IOPAD(0x0294, PIN_INPUT_PULLUP, 0) /* (J19) MMC1_CMD */
- AM64X_IOPAD(0x028c, PIN_INPUT_PULLDOWN, 0) /* (L20) MMC1_CLK */
- AM64X_IOPAD(0x0288, PIN_INPUT_PULLUP, 0) /* (K21) MMC1_DAT0 */
- AM64X_IOPAD(0x0284, PIN_INPUT_PULLUP, 0) /* (L21) MMC1_DAT1 */
- AM64X_IOPAD(0x0280, PIN_INPUT_PULLUP, 0) /* (K19) MMC1_DAT2 */
- AM64X_IOPAD(0x027c, PIN_INPUT_PULLUP, 0) /* (K18) MMC1_DAT3 */
- AM64X_IOPAD(0x0298, PIN_INPUT_PULLUP, 0) /* (D19) MMC1_SDCD */
- AM64X_IOPAD(0x029c, PIN_INPUT_PULLUP, 0) /* (C20) MMC1_SDWP */
- >;
- };
-
- main_usb0_pins_default: main-usb0-pins-default {
- bootph-pre-ram;
- pinctrl-single,pins = <
- AM64X_IOPAD(0x02a8, PIN_OUTPUT, 0) /* (E19) USB0_DRVVBUS */
- >;
- };
-
- mdio1_pins_default: mdio1-pins-default {
- pinctrl-single,pins = <
- AM64X_IOPAD(0x01fc, PIN_OUTPUT, 4) /* (R2) PRG0_PRU1_GPO19.MDIO0_MDC */
- AM64X_IOPAD(0x01f8, PIN_INPUT, 4) /* (P5) PRG0_PRU1_GPO18.MDIO0_MDIO */
- >;
- };
-
- rgmii1_pins_default: rgmii1-pins-default {
- pinctrl-single,pins = <
- AM64X_IOPAD(0x011c, PIN_INPUT, 4) /* (AA13) PRG1_PRU1_GPO5.RGMII1_RD0 */
- AM64X_IOPAD(0x0128, PIN_INPUT, 4) /* (U12) PRG1_PRU1_GPO8.RGMII1_RD1 */
- AM64X_IOPAD(0x0150, PIN_INPUT, 4) /* (Y13) PRG1_PRU1_GPO18.RGMII1_RD2 */
- AM64X_IOPAD(0x0154, PIN_INPUT, 4) /* (V12) PRG1_PRU1_GPO19.RGMII1_RD3 */
- AM64X_IOPAD(0x00d8, PIN_INPUT, 4) /* (W13) PRG1_PRU0_GPO8.RGMII1_RXC */
- AM64X_IOPAD(0x00cc, PIN_INPUT, 4) /* (V13) PRG1_PRU0_GPO5.RGMII1_RX_CTL */
- AM64X_IOPAD(0x0124, PIN_OUTPUT, 4) /* (V15) PRG1_PRU1_GPO7.RGMII1_TD0 */
- AM64X_IOPAD(0x012c, PIN_OUTPUT, 4) /* (V14) PRG1_PRU1_GPO9.RGMII1_TD1 */
- AM64X_IOPAD(0x0130, PIN_OUTPUT, 4) /* (W14) PRG1_PRU1_GPO10.RGMII1_TD2 */
- AM64X_IOPAD(0x014c, PIN_OUTPUT, 4) /* (AA14) PRG1_PRU1_GPO17.RGMII1_TD3 */
- AM64X_IOPAD(0x00e0, PIN_OUTPUT, 4) /* (U14) PRG1_PRU0_GPO10.RGMII1_TXC */
- AM64X_IOPAD(0x00dc, PIN_OUTPUT, 4) /* (U15) PRG1_PRU0_GPO9.RGMII1_TX_CTL */
- >;
- };
-
- rgmii2_pins_default: rgmii2-pins-default {
- pinctrl-single,pins = <
- AM64X_IOPAD(0x0108, PIN_INPUT, 4) /* (W11) PRG1_PRU1_GPO0.RGMII2_RD0 */
- AM64X_IOPAD(0x010c, PIN_INPUT, 4) /* (V11) PRG1_PRU1_GPO1.RGMII2_RD1 */
- AM64X_IOPAD(0x0110, PIN_INPUT, 4) /* (AA12) PRG1_PRU1_GPO2.RGMII2_RD2 */
- AM64X_IOPAD(0x0114, PIN_INPUT, 4) /* (Y12) PRG1_PRU1_GPO3.RGMII2_RD3 */
- AM64X_IOPAD(0x0120, PIN_INPUT, 4) /* (U11) PRG1_PRU1_GPO6.RGMII2_RXC */
- AM64X_IOPAD(0x0118, PIN_INPUT, 4) /* (W12) PRG1_PRU1_GPO4.RGMII2_RX_CTL */
- AM64X_IOPAD(0x0134, PIN_OUTPUT, 4) /* (AA10) PRG1_PRU1_GPO11.RGMII2_TD0 */
- AM64X_IOPAD(0x0138, PIN_OUTPUT, 4) /* (V10) PRG1_PRU1_GPO12.RGMII2_TD1 */
- AM64X_IOPAD(0x013c, PIN_OUTPUT, 4) /* (U10) PRG1_PRU1_GPO13.RGMII2_TD2 */
- AM64X_IOPAD(0x0140, PIN_OUTPUT, 4) /* (AA11) PRG1_PRU1_GPO14.RGMII2_TD3 */
- AM64X_IOPAD(0x0148, PIN_OUTPUT, 4) /* (Y10) PRG1_PRU1_GPO16.RGMII2_TXC */
- AM64X_IOPAD(0x0144, PIN_OUTPUT, 4) /* (Y11) PRG1_PRU1_GPO15.RGMII2_TX_CTL */
- >;
- };
-};
-
&dmsc {
+ bootph-pre-ram;
mboxes= <&secure_proxy_main 0>,
<&secure_proxy_main 1>,
<&secure_proxy_main 0>;
@@ -189,78 +81,28 @@
};
&main_uart0 {
+ /* Clocked by default - enable early in boot to get debug logs */
/delete-property/ power-domains;
/delete-property/ clocks;
/delete-property/ clock-names;
- pinctrl-names = "default";
- pinctrl-0 = <&main_uart0_pins_default>;
- status = "okay";
+};
+
+&main_uart1_pins_default {
+ bootph-pre-ram;
};
&main_uart1 {
bootph-pre-ram;
- pinctrl-names = "default";
- pinctrl-0 = <&main_uart1_pins_default>;
+};
+
+/* EEPROM might be read before SYSFW is available */
+&main_i2c0 {
+ /delete-property/ power-domains;
};
&sdhci1 {
+ /* Clocked by default */
/delete-property/ power-domains;
clocks = <&clk_200mhz>;
clock-names = "clk_xin";
- ti,driver-strength-ohm = <50>;
- disable-wp;
- pinctrl-0 = <&main_mmc1_pins_default>;
-};
-
-&serdes_ln_ctrl {
- idle-states = <AM64_SERDES0_LANE0_USB>;
-};
-
-&serdes_wiz0 {
- status = "okay";
-};
-
-&serdes0 {
- serdes0_usb_link: link@0 {
- reg = <0>;
- cdns,num-lanes = <1>;
- #phy-cells = <0>;
- cdns,phy-type = <PHY_TYPE_USB3>;
- resets = <&serdes_wiz0 1>;
- };
-};
-
-&usbss0 {
- ti,vbus-divider;
-};
-
-&usb0 {
- dr_mode = "host";
- maximum-speed = "super-speed";
- pinctrl-names = "default";
- pinctrl-0 = <&main_usb0_pins_default>;
- phys = <&serdes0_usb_link>;
- phy-names = "cdns3,usb3-phy";
-};
-
-&cpsw3g {
- pinctrl-names = "default";
- pinctrl-0 = <&mdio1_pins_default
- &rgmii1_pins_default
- &rgmii2_pins_default>;
};
-
-&cpsw_port2 {
- phy-mode = "rgmii-rxid";
- phy-handle = <&cpsw3g_phy1>;
-};
-
-&cpsw3g_mdio {
- cpsw3g_phy1: ethernet-phy@1 {
- reg = <1>;
- ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
- ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
- };
-};
-
-#include "k3-am642-sk-u-boot.dtsi"
--
2.40.0
next prev parent reply other threads:[~2023-04-14 8:00 UTC|newest]
Thread overview: 31+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-04-14 7:57 [PATCH 00/23] arm: dts: k3-am64: Sync with kernel.org and Nishanth Menon
2023-04-14 7:57 ` [PATCH 01/23] Revert "ARM: dts: k3-am642-sk-u-boot: add PMIC node" Nishanth Menon
2023-04-14 7:57 ` [PATCH 02/23] arm: dts: k3-am64: Update devicetree to sync with v6.3-rc6 Nishanth Menon
2023-04-14 7:57 ` [PATCH 03/23] arm: dts: k3-am642-sk: Add a note to handle pinmux till MDIO DM conversion is done Nishanth Menon
2023-04-14 7:57 ` [PATCH 04/23] arm: dts: k3-am642-sk: Fix mmc1 pinmux pull polarity Nishanth Menon
2023-04-17 10:42 ` Roger Quadros
2023-04-17 11:12 ` Nishanth Menon
2023-04-17 11:45 ` Roger Quadros
2023-04-17 13:25 ` Nishanth Menon
2023-04-14 7:57 ` [PATCH 05/23] arm: dts: k3-am642-sk: Add main_uart1 description Nishanth Menon
2023-04-14 7:57 ` [PATCH 06/23] arm: dts: k3-am642-sk: Add main_i2c0 and eeprom Nishanth Menon
2023-04-14 7:57 ` [PATCH 07/23] arm: dts: k3-am642-sk-u-boot: Drop the i2c node Nishanth Menon
2023-04-14 7:57 ` [PATCH 08/23] arm: dts: k3-am642-sk-u-boot: Drop redundant usb dr_mode property Nishanth Menon
2023-04-14 7:57 ` [PATCH 09/23] arm: dts: k3-am642-sk-u-boot: Mark main_uart0 to be used for spl Nishanth Menon
2023-04-14 7:57 ` [PATCH 10/23] arm: dts: k3-am642-sk-u-boot: Document timer as missing upstream Nishanth Menon
2023-04-14 7:57 ` [PATCH 11/23] arm: dts: k3-am642-sk-u-boot: Drop aliases and stdout Nishanth Menon
2023-04-14 7:57 ` Nishanth Menon [this message]
2023-04-18 9:15 ` [PATCH 12/23] arm: dts: k3-am642-r5-sk: Use am642-sk.dts and k3-am642-sk-u-boot.dtsi Manorit Chawdhry
2023-04-18 12:34 ` Nishanth Menon
2023-04-19 4:53 ` Manorit Chawdhry
2023-04-14 7:57 ` [PATCH 13/23] arm: dts: k3-am642-evm: Move the mdio pinmux down to evm.dts Nishanth Menon
2023-04-14 7:57 ` [PATCH 14/23] arm: dts: k3-am642-evm: Add DDR vtt regulator Nishanth Menon
2023-04-14 7:57 ` [PATCH 15/23] arm: dts: k3-am642-evm: Add main_uart1 description Nishanth Menon
2023-04-14 7:57 ` [PATCH 16/23] arm: dts: k3-am642-evm: Add main_i2c0 and eeprom Nishanth Menon
2023-04-14 7:57 ` [PATCH 17/23] arm: dts: k3-am642-evm-u-boot: Drop the i2c node Nishanth Menon
2023-04-14 7:57 ` [PATCH 18/23] arm: dts: k3-am642-evm-u-boot: Drop stdout and cosmetic fixups Nishanth Menon
2023-04-14 7:57 ` [PATCH 19/23] arm: dts: k3-am642-evm-u-boot: Re-organize the pinmux Nishanth Menon
2023-04-14 7:57 ` [PATCH 20/23] arm: dts: k3-am642-evm-u-boot: Add missing pinmux notations Nishanth Menon
2023-04-14 7:57 ` [PATCH 21/23] arm: dts: k3-am642-r5-evm: Use am642-evm.dts and k3-am642-evm-u-boot.dtsi Nishanth Menon
2023-04-14 7:57 ` [PATCH 22/23] include: configs: am64x_evm: Change to using .env Nishanth Menon
2023-04-14 7:57 ` [PATCH 23/23] configs: am64x_evm_a53_defconfig: Just use distroboot Nishanth Menon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230414075726.387461-13-nm@ti.com \
--to=nm@ti.com \
--cc=g-vlaev@ti.com \
--cc=gadiyar@ti.com \
--cc=n-francis@ti.com \
--cc=n-jain1@ti.com \
--cc=neil.armstrong@linaro.org \
--cc=rogerq@kernel.org \
--cc=sjg@chromium.org \
--cc=trini@konsulko.com \
--cc=u-boot@lists.denx.de \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox