From: Thomas Richard <thomas.richard@bootlin.com>
To: u-boot@lists.denx.de
Cc: nm@ti.com, thomas.richard@bootlin.com,
thomas.petazzoni@bootlin.com, gregory.clement@bootlin.com,
u-kumar1@ti.com, Bryan Brattlof <bb@ti.com>,
Gowtham Tammana <g-tammana@ti.com>,
Manorit Chawdhry <m-chawdhry@ti.com>,
Neha Malcom Francis <n-francis@ti.com>,
Simon Glass <sjg@chromium.org>, Tom Rini <trini@konsulko.com>
Subject: [PATCH v2 0/8] Suspend to RAM support for K3 J7200
Date: Tue, 7 Nov 2023 17:17:54 +0100 [thread overview]
Message-ID: <20231107161802.855154-1-thomas.richard@bootlin.com> (raw)
This series is the U-Boot part of the work to add the suspend to RAM
support for the K3 J7200 EVM board.
During the boot R5 SPL makes a copy of DM-Firmware in memory.
Resume detection is done by reading a magic value in a pmic register
(set by DM-Firmware).
If a resume is detected, R5 SPL run the exit retention sequence of the
DDR. Then it restores TF-A in SRAM (it saved itself to DDR), and load
DM-Firmware using the copy done during the boot (fit image processing
is skipped).
The copy of TF-A/DM-Firmware, the SPL stack and malloc are located in a
reserved memory region (for the kernel point of view) to avoid any
memory corruption.
Changes in v2:
- Set exit retention code for DDR behind CONFIG_K3_J721E_DDRSS
- Check if TF-A is running in DRAM, if yes no need to restore it
- Remove BL31_START macro, and get TF-A start address from the fit image
- Remove the test_enter_suspend command
- Link to v1: https://lore.kernel.org/u-boot/20231016141135.325698-1-thomas.richard@bootlin.com/
Gowtham Tammana (1):
DO NOT MERGE: arm: dts: k3-j7200-r5-common: Add pmic node for esm
Gregory CLEMENT (2):
configs: j7200_evm_r5: Used reserved memory in DDR for stack
configs: j7200_evm_r5: Move address used for allocation in the
reserved space
Thomas Richard (5):
board: ti: j721e: Add resume detection for J7200
ram: k3-ddrss: Add exit retention support
board: ti: j721e: Add the missing part of exit retention for k3-ddrss
(J7200)
board: ti: j721e: During resume spl restores TF-A and DM-Firmware
arm: mach-k3: j7200: Skip fit processing when resuming
.../arm/dts/k3-j7200-r5-common-proc-board.dts | 17 +-
arch/arm/mach-k3/common.c | 48 ++-
arch/arm/mach-k3/include/mach/j721e_spl.h | 28 ++
arch/arm/mach-k3/sysfw-loader.c | 16 +-
board/ti/j721e/evm.c | 79 +++++
configs/j7200_evm_r5_defconfig | 4 +-
drivers/ram/k3-ddrss/k3-ddrss.c | 307 ++++++++++++++++++
7 files changed, 489 insertions(+), 10 deletions(-)
--
2.39.2
next reply other threads:[~2023-11-07 16:18 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-11-07 16:17 Thomas Richard [this message]
2023-11-07 16:17 ` [PATCH v2 1/8] DO NOT MERGE: arm: dts: k3-j7200-r5-common: Add pmic node for esm Thomas Richard
2023-11-07 16:17 ` [PATCH v2 2/8] configs: j7200_evm_r5: Used reserved memory in DDR for stack Thomas Richard
2023-11-07 18:12 ` Tom Rini
2023-11-07 16:17 ` [PATCH v2 3/8] configs: j7200_evm_r5: Move address used for allocation in the reserved space Thomas Richard
2023-11-07 16:17 ` [PATCH v2 4/8] board: ti: j721e: Add resume detection for J7200 Thomas Richard
2023-11-07 18:16 ` Tom Rini
2023-11-07 16:17 ` [PATCH v2 5/8] ram: k3-ddrss: Add exit retention support Thomas Richard
2023-11-07 16:18 ` [PATCH v2 6/8] board: ti: j721e: Add the missing part of exit retention for k3-ddrss (J7200) Thomas Richard
2023-11-07 18:18 ` Tom Rini
2023-11-09 10:43 ` Thomas Richard
2023-11-09 14:07 ` Tom Rini
2023-11-07 16:18 ` [PATCH v2 7/8] board: ti: j721e: During resume spl restores TF-A and DM-Firmware Thomas Richard
2023-11-07 18:26 ` Tom Rini
2023-11-08 17:30 ` Andrew Davis
2023-11-09 11:29 ` Thomas Richard
2023-11-09 16:17 ` Andrew Davis
2023-11-07 16:18 ` [PATCH v2 8/8] arm: mach-k3: j7200: Skip fit processing when resuming Thomas Richard
2023-11-07 18:06 ` [PATCH v2 0/8] Suspend to RAM support for K3 J7200 Tom Rini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20231107161802.855154-1-thomas.richard@bootlin.com \
--to=thomas.richard@bootlin.com \
--cc=bb@ti.com \
--cc=g-tammana@ti.com \
--cc=gregory.clement@bootlin.com \
--cc=m-chawdhry@ti.com \
--cc=n-francis@ti.com \
--cc=nm@ti.com \
--cc=sjg@chromium.org \
--cc=thomas.petazzoni@bootlin.com \
--cc=trini@konsulko.com \
--cc=u-boot@lists.denx.de \
--cc=u-kumar1@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox