From: Linus Walleij <linusw@kernel.org>
To: u-boot@lists.u-boot-project.org, Tom Rini <trini@konsulko.com>,
Stefan Hansson <newbyte@postmarketos.org>,
Stephan Gerhold <stephan.gerhold@linaro.org>
Cc: Linus Walleij <linusw@kernel.org>
Subject: [PATCH v2 4/8] power: regulator: Add AB8500 AUX3 support
Date: Mon, 17 Aug 2026 11:31:53 +0200 [thread overview]
Message-ID: <20260817-ux500-external-sdcard-v2-4-ca9a110bd9c6@kernel.org> (raw)
In-Reply-To: <20260817-ux500-external-sdcard-v2-0-ca9a110bd9c6@kernel.org>
Add regulator support for LDO AUX3 on AB8500 and AB8505 PMICs.
AUX3 supplies the removable SD card on the upstream Ux500 Samsung
device trees, and both PMIC variants use the same control registers.
Imply the regulator core for ARCH_U8500 so the driver can instantiate
from the upstream device trees.
Signed-off-by: Linus Walleij <linusw@kernel.org>
---
MAINTAINERS | 1 +
arch/arm/Kconfig | 2 +
drivers/power/pmic/ab8500.c | 1 +
drivers/power/regulator/Kconfig | 7 +++
drivers/power/regulator/Makefile | 1 +
drivers/power/regulator/ab8500.c | 111 +++++++++++++++++++++++++++++++++++++++
6 files changed, 123 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index a5d6b5be29dc..8e78a7f224fa 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -790,6 +790,7 @@ F: drivers/gpio/nmk_gpio.c
F: drivers/pinctrl/pinctrl-nomadik.c
F: drivers/phy/phy-ab8500-usb.c
F: drivers/power/pmic/ab8500.c
+F: drivers/power/regulator/ab8500.c
F: drivers/timer/nomadik-mtu-timer.c
F: drivers/usb/musb-new/ux500.c
F: drivers/video/mcde_simple.c
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 5b02ff18bd0e..62aa9e8cc565 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -1275,6 +1275,7 @@ config ARCH_U8500
imply ARM_PL180_MMCI
imply CLK
imply DM_PMIC
+ imply DM_REGULATOR
imply DM_RTC
imply NOMADIK_GPIO
imply NOMADIK_MTU_TIMER
@@ -1283,6 +1284,7 @@ config ARCH_U8500
imply PHY
imply PL01X_SERIAL
imply PMIC_AB8500
+ imply REGULATOR_AB8500
imply RTC_PL031
imply SYS_THUMB_BUILD
imply SYSRESET_SYSCON
diff --git a/drivers/power/pmic/ab8500.c b/drivers/power/pmic/ab8500.c
index 9ba096711e14..b9fae7000b78 100644
--- a/drivers/power/pmic/ab8500.c
+++ b/drivers/power/pmic/ab8500.c
@@ -253,6 +253,7 @@ static int ab8500_probe(struct udevice *dev)
static const struct udevice_id ab8500_ids[] = {
{ .compatible = "stericsson,ab8500" },
+ { .compatible = "stericsson,ab8505" },
{ }
};
diff --git a/drivers/power/regulator/Kconfig b/drivers/power/regulator/Kconfig
index 00a25acfdf99..a27fe4925cf9 100644
--- a/drivers/power/regulator/Kconfig
+++ b/drivers/power/regulator/Kconfig
@@ -16,6 +16,13 @@ config DM_REGULATOR
for this purpose if PMIC I/O driver is implemented or dm_scan_fdt_dev()
otherwise. Detailed information can be found in the header file.
+config REGULATOR_AB8500
+ bool "ST-Ericsson AB8500/AB8505 regulator support"
+ depends on DM_REGULATOR && PMIC_AB8500
+ help
+ Enable LDO AUX3 regulator support for AB8500 and AB8505 PMICs.
+ This supply is used to power removable SD cards on Ux500 boards.
+
config SPL_DM_REGULATOR
bool "Enable regulators for SPL"
depends on DM_REGULATOR && SPL_POWER
diff --git a/drivers/power/regulator/Makefile b/drivers/power/regulator/Makefile
index a40c9d340d98..a500a3da98d4 100644
--- a/drivers/power/regulator/Makefile
+++ b/drivers/power/regulator/Makefile
@@ -5,6 +5,7 @@
#
obj-$(CONFIG_$(PHASE_)DM_REGULATOR) += regulator-uclass.o
+obj-$(CONFIG_REGULATOR_AB8500) += ab8500.o
obj-$(CONFIG_REGULATOR_ACT8846) += act8846.o
obj-$(CONFIG_REGULATOR_AS3722) += as3722_regulator.o
obj-$(CONFIG_$(PHASE_)REGULATOR_AXP) += axp_regulator.o
diff --git a/drivers/power/regulator/ab8500.c b/drivers/power/regulator/ab8500.c
new file mode 100644
index 000000000000..03beb0834d53
--- /dev/null
+++ b/drivers/power/regulator/ab8500.c
@@ -0,0 +1,111 @@
+// SPDX-License-Identifier: GPL-2.0+
+/* ST-Ericsson AB8500/AB8505 LDO AUX3 regulator */
+
+#include <dm.h>
+#include <dm/device-internal.h>
+#include <dm/lists.h>
+#include <linux/errno.h>
+#include <power/ab8500.h>
+#include <power/pmic.h>
+#include <power/regulator.h>
+
+#define AB8500_VAUX3_REGU AB8500_REGU_CTRL2(0x0a)
+#define AB8500_VAUX3_SEL AB8500_REGU_CTRL2(0x21)
+#define AB8500_VAUX3_EN_MASK GENMASK(1, 0)
+#define AB8500_VAUX3_EN BIT(0)
+#define AB8500_VAUX3_SEL_MASK GENMASK(2, 0)
+
+static const int ab8500_vaux3_voltages[] = {
+ 1200000, 1500000, 1800000, 2100000,
+ 2500000, 2750000, 2790000, 2910000,
+};
+
+static struct udevice *ab8500_regulator_pmic(struct udevice *dev)
+{
+ return dev->parent->parent;
+}
+
+static int ab8500_regulator_get_value(struct udevice *dev)
+{
+ int ret;
+
+ ret = pmic_reg_read(ab8500_regulator_pmic(dev), AB8500_VAUX3_SEL);
+ if (ret < 0)
+ return ret;
+ ret &= AB8500_VAUX3_SEL_MASK;
+
+ return ab8500_vaux3_voltages[ret];
+}
+
+static int ab8500_regulator_set_value(struct udevice *dev, int uV)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(ab8500_vaux3_voltages); i++) {
+ if (ab8500_vaux3_voltages[i] == uV)
+ return pmic_clrsetbits(ab8500_regulator_pmic(dev),
+ AB8500_VAUX3_SEL,
+ AB8500_VAUX3_SEL_MASK, i);
+ }
+
+ return -EINVAL;
+}
+
+static int ab8500_regulator_get_enable(struct udevice *dev)
+{
+ int ret;
+
+ ret = pmic_reg_read(ab8500_regulator_pmic(dev), AB8500_VAUX3_REGU);
+ if (ret < 0)
+ return ret;
+
+ return (ret & AB8500_VAUX3_EN_MASK) == AB8500_VAUX3_EN;
+}
+
+static int ab8500_regulator_set_enable(struct udevice *dev, bool enable)
+{
+ return pmic_clrsetbits(ab8500_regulator_pmic(dev), AB8500_VAUX3_REGU,
+ AB8500_VAUX3_EN_MASK,
+ enable ? AB8500_VAUX3_EN : 0);
+}
+
+static const struct dm_regulator_ops ab8500_regulator_ops = {
+ .get_value = ab8500_regulator_get_value,
+ .set_value = ab8500_regulator_set_value,
+ .get_enable = ab8500_regulator_get_enable,
+ .set_enable = ab8500_regulator_set_enable,
+};
+
+U_BOOT_DRIVER(ab8500_ldo_aux3) = {
+ .name = "ab8500_ldo_aux3",
+ .id = UCLASS_REGULATOR,
+ .ops = &ab8500_regulator_ops,
+};
+
+static int ab8500_regulators_bind(struct udevice *dev)
+{
+ struct driver *drv = lists_driver_lookup_name("ab8500_ldo_aux3");
+ ofnode node;
+
+ dev_for_each_subnode(node, dev) {
+ if (!strcmp(ofnode_get_name(node), "ab8500_ldo_aux3"))
+ return device_bind_with_driver_data(dev, drv,
+ ofnode_get_name(node), 0,
+ node, NULL);
+ }
+
+ return -ENODEV;
+}
+
+static const struct udevice_id ab8500_regulator_ids[] = {
+ { .compatible = "stericsson,ab8500-regulator" },
+ { .compatible = "stericsson,ab8505-regulator" },
+ { }
+};
+
+U_BOOT_DRIVER(ab8500_regulators) = {
+ .name = "ab8500_regulators",
+ .id = UCLASS_NOP,
+ .of_match = ab8500_regulator_ids,
+ .bind = ab8500_regulators_bind,
+};
--
2.55.0
next prev parent reply other threads:[~2026-08-17 13:34 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-08-17 9:31 [PATCH v2 0/8] arm: u8500: Enable upstream DT based SD card boot Linus Walleij
2026-08-17 9:31 ` [PATCH v2 1/8] pinctrl: Add compact Nomadik pin controller Linus Walleij
2026-08-17 15:57 ` Stephan Gerhold
2026-08-17 9:31 ` [PATCH v2 2/8] mmc: arm_pl180: Configure Ux500 signal direction Linus Walleij
2026-08-17 15:59 ` Stephan Gerhold
2026-08-17 9:31 ` [PATCH v2 3/8] mmc: arm_pl180: Set initial supply voltages Linus Walleij
2026-08-17 16:15 ` Stephan Gerhold
2026-08-17 9:31 ` Linus Walleij [this message]
2026-08-17 16:21 ` [PATCH v2 4/8] power: regulator: Add AB8500 AUX3 support Stephan Gerhold
2026-08-17 9:31 ` [PATCH v2 5/8] configs: stemmy: Enable SD card regulators Linus Walleij
2026-08-17 16:24 ` Stephan Gerhold
2026-08-17 9:31 ` [PATCH v2 6/8] configs: stemmy: Boot EFI from external SD card Linus Walleij
2026-08-17 16:29 ` Stephan Gerhold
2026-08-17 9:31 ` [PATCH v2 7/8] arm: u8500: Switch Stemmy to upstream Janice device tree Linus Walleij
2026-08-17 16:45 ` Stephan Gerhold
2026-08-17 20:54 ` Linus Walleij
2026-08-18 10:39 ` Stephan Gerhold
2026-08-18 13:31 ` Linus Walleij
2026-08-19 8:53 ` Linus Walleij
2026-08-17 9:31 ` [PATCH v2 8/8] arm: u8500: Give Golden panel regulators unique names Linus Walleij
2026-08-17 16:47 ` Stephan Gerhold
2026-08-17 20:36 ` Linus Walleij
2026-08-17 21:14 ` Tom Rini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260817-ux500-external-sdcard-v2-4-ca9a110bd9c6@kernel.org \
--to=linusw@kernel.org \
--cc=newbyte@postmarketos.org \
--cc=stephan.gerhold@linaro.org \
--cc=trini@konsulko.com \
--cc=u-boot@lists.u-boot-project.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox