[U-Boot] [U-boot] U-Boot 2009.03 booting problem

[U-Boot] [U-boot] U-Boot 2009.03 booting problem

[rudresh]

Hi All,

I am try to use the u-boot version 2009 for MPC8313ERB broad, when i load
the u-boot.bin to board using JTAG and restart the board at that time its
not booting properly . its generated following error what may be the
problem.

U-Boot 2009.03 (Apr 22 2009 - 04:59:44) MPC83XX

Reset Status: Software Hard, External/Internal Soft, External/Internal Hard

CPU:   e300c3, MPC8313E, Rev: 1.0 at 333.333 MHz, CSB: 166.667 MHz
Board: Freescale MPC8313ERDB
I2C:   ready
DRAM:  128 MB
FLASH: 16 MB
NAND:  256 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Machine check in kernel mode.
Caused by (from msr): regs 07f36df0 Unknown values in msr
NIP: 07FE9474 XER: 00000000 LR: 07FE946C REGS: 07f36df0 TRAP: 0200 DAR:
00000000
MSR: 00003030 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 11

GPR00: 0000007C 07F36EE0 07F36F4C FFFFFFFF FFFFFFFF 00000000 00000000
04AA7D46
GPR08: 07FBDE54 F001C048 00000090 07FEA3D0 07F36F4C 000080A0 07FFC000
09FB9000
GPR16: 00000080 00006101 20044000 00020052 FFFFFFFF FFFFFFFF 00000000
07FBC098
GPR24: 07FBCAD8 FFFF80A0 00000001 FE7FE000 00002000 00000000 07FFD5A4
07F36FBC
Call backtrace:
07FE946C 07FE1784 07FBD968 07FBC5E8
machine check
Resetting the board.


Regards
Rudresh
-- 
View this message in context: http://www.nabble.com/-U-boot--U-Boot-2009.03-booting-problem-tp22969997p22969997.html
Sent from the Uboot - Users mailing list archive at Nabble.com.

[U-Boot] [U-boot] U-Boot 2009.03 booting problem

[Kim Phillips]

On Thu, 9 Apr 2009 05:32:29 -0700 (PDT)
rudresh <rudresh.tk@lntemsys.com> wrote:

> 
> Hi All,
> 
> I am try to use the u-boot version 2009 for MPC8313ERB broad, when i load
> the u-boot.bin to board using JTAG and restart the board at that time its
> not booting properly . its generated following error what may be the
> problem.
> 
> U-Boot 2009.03 (Apr 22 2009 - 04:59:44) MPC83XX
> 
> Reset Status: Software Hard, External/Internal Soft, External/Internal Hard
> 
> CPU:   e300c3, MPC8313E, Rev: 1.0 at 333.333 MHz, CSB: 166.667 MHz
> Board: Freescale MPC8313ERDB
> I2C:   ready
> DRAM:  128 MB
> FLASH: 16 MB
> NAND:  256 MiB
> *** Warning - bad CRC, using default environment
> 
> In:    serial
> Out:   serial
> Err:   serial
> Machine check in kernel mode.
> Caused by (from msr): regs 07f36df0 Unknown values in msr
> NIP: 07FE9474 XER: 00000000 LR: 07FE946C REGS: 07f36df0 TRAP: 0200 DAR:
> 00000000

can you turn on debugging and/or somehow find out what code is at or
around the NIP address above?

Also, how, if any, is this board different from Freescale's
MPC8313ERDB?  earlier you state it is a custom board...

Kim