From: Tero Kristo <kristo@kernel.org>
To: Lokesh Vutla <lokeshvutla@ti.com>,
trini@konsulko.com, u-boot@lists.denx.de
Subject: Re: [PATCHv6 00/26] HSM rearch series for TI K3 devices
Date: Fri, 11 Jun 2021 14:18:46 +0300 [thread overview]
Message-ID: <22da4ad1-8a11-50fb-7e97-2caa0ee187dc@kernel.org> (raw)
In-Reply-To: <2a06a7d2-8101-91e9-3813-ce9d4f327d84@ti.com>
On 11/06/2021 14:08, Lokesh Vutla wrote:
> Hi Tero,
>
> On 11/06/21 2:15 pm, Tero Kristo wrote:
>> Hello,
>>
>> One more post, this time with the #ifdef hackery converted to use the
>> IS_ENABLED / CONFIG_IS_ENABLED macros, and also removed the "common.h"
>> include from k3-clk.h header. This version also contains fixes to any
>> build issues reported by Lokesh, and these are squashed in to relevant
>> patches.
>
> Can you see if the below warnings can be fixed?
>
> hsm/0018-arm-mach-k3-add-support-for-detecting-firmware-image.patch
> -------------------------------------------------------------------
> WARNING: Use 'if (IS_ENABLED(CONFIG...))' instead of '#if or #ifdef' where possible
> #26: FILE: arch/arm/mach-k3/common.c:31:
> +#if IS_ENABLED(CONFIG_SYS_K3_SPL_ATF)
This is static data, can't be fixed. Unless we want to compile it in always?
>
> WARNING: Use 'if (IS_ENABLED(CONFIG...))' instead of '#if or #ifdef' where possible
> #35: FILE: arch/arm/mach-k3/common.c:40:
> +#if CONFIG_IS_ENABLED(FIT_IMAGE_POST_PROCESS)
Same, static data.
>
> WARNING: Use 'if (IS_ENABLED(CONFIG...))' instead of '#if or #ifdef' where possible
> #55: FILE: arch/arm/mach-k3/common.c:131:
> +#if IS_ENABLED(CONFIG_SYS_K3_SPL_ATF)
This is actually just an old macro I changed from #ifdef to IS_ENABLED.
Fixing the whole file from the existing #ifdef:s should be outside the
scope of this series.
>
> WARNING: Use 'if (IS_ENABLED(CONFIG...))' instead of '#if or #ifdef' where possible
> #124: FILE: arch/arm/mach-k3/common.c:264:
> +#if CONFIG_IS_ENABLED(FIT_IMAGE_POST_PROCESS)
This code addresses the static data defined before, changing this will
break compilation; unless we compile the data always in.
>
> WARNING: Use 'if (IS_ENABLED(CONFIG...))' instead of '#if or #ifdef' where possible
> #128: FILE: arch/arm/mach-k3/common.c:268:
> +#if IS_ENABLED(CONFIG_SYS_K3_SPL_ATF)
Same as above.
> WARNING: Use 'if (IS_ENABLED(CONFIG...))' instead of '#if or #ifdef' where possible
> #150: FILE: arch/arm/mach-k3/common.c:290:
> +#if IS_ENABLED(CONFIG_TI_SECURE_DEVICE)
This can't be changed, the code it addresses is only linked in with the
config, causing a linker time failure if this is fixed.
Imho, I am not too convinced about the checkpatch tool complaining about
these issues. :)
-Tero
>
> total: 0 errors, 6 warnings, 0 checks, 144 lines checked
>
> NOTE: For some of the reported defects, checkpatch may be able to
> mechanically convert to the typical style using --fix or --fix-inplace.
>
> hsm/0018-arm-mach-k3-add-support-for-detecting-firmware-image.patch has style
> problems, please review.
> -------------------------------------------------------------------
> hsm/0019-arm-mach-k3-do-board-config-for-PM-only-if-supported.patch
> -------------------------------------------------------------------
> WARNING: Use 'if (IS_ENABLED(CONFIG...))' instead of '#if or #ifdef' where possible
> #24: FILE: arch/arm/mach-k3/sysfw-loader.c:162:
> +#if !CONFIG_IS_ENABLED(K3_DM_FW)
>
> total: 0 errors, 1 warnings, 0 checks, 13 lines checked
>
> NOTE: For some of the reported defects, checkpatch may be able to
> mechanically convert to the typical style using --fix or --fix-inplace.
>
>
> Thanks and regards,
> Lokesh
>
next prev parent reply other threads:[~2021-06-11 11:18 UTC|newest]
Thread overview: 31+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-06-11 8:45 [PATCHv6 00/26] HSM rearch series for TI K3 devices Tero Kristo
2021-06-11 8:45 ` [PATCHv6 01/26] lib: rational: copy the rational fraction lib routines from Linux Tero Kristo
2021-06-11 8:45 ` [PATCHv6 02/26] arm: mach-k3: introduce new config option for sysfw split Tero Kristo
2021-06-11 8:45 ` [PATCHv6 03/26] remoteproc: k3-r5: remove sysfw PM calls if not supported Tero Kristo
2021-06-11 8:45 ` [PATCHv6 04/26] common: fit: Update board_fit_image_post_process() to pass fit and node_offset Tero Kristo
2021-06-11 8:45 ` [PATCHv6 05/26] clk: fixed_rate: add API for directly registering fixed rate clocks Tero Kristo
2021-06-11 8:45 ` [PATCHv6 06/26] clk: fix clock tree dump to properly dump out every registered clock Tero Kristo
2021-06-11 8:45 ` [PATCHv6 07/26] clk: do not attempt to fetch clock pointer with null device Tero Kristo
2021-06-11 8:45 ` [PATCHv6 08/26] clk: add support for setting clk rate from cmdline Tero Kristo
2021-06-11 8:45 ` [PATCHv6 09/26] clk: sci-clk: fix return value of set_rate Tero Kristo
2021-06-11 8:45 ` [PATCHv6 10/26] clk: fix assigned-clocks to pass with deferring provider Tero Kristo
2021-06-11 8:45 ` [PATCHv6 11/26] clk: fix set_rate to clean up cached rates for the hierarchy Tero Kristo
2021-06-11 8:45 ` [PATCHv6 12/26] clk: add support for TI K3 SoC PLL Tero Kristo
2021-06-11 8:45 ` [PATCHv6 13/26] clk: add support for TI K3 SoC clocks Tero Kristo
2021-06-11 8:45 ` [PATCHv6 14/26] power: domain: Introduce driver for raw TI K3 PDs Tero Kristo
2021-06-11 8:45 ` [PATCHv6 15/26] cmd: ti: pd: Add debug command for K3 power domains Tero Kristo
2021-06-11 8:45 ` [PATCHv6 16/26] tools: k3_fit_atf: add DM binary to the FIT image Tero Kristo
2021-06-11 8:45 ` [PATCHv6 17/26] arm: mach-k3: Add platform data for j721e and j7200 Tero Kristo
2021-06-11 8:45 ` [PATCHv6 18/26] arm: mach-k3: add support for detecting firmware images from FIT Tero Kristo
2021-06-11 8:45 ` [PATCHv6 19/26] arm: mach-k3: do board config for PM only if supported Tero Kristo
2021-06-11 8:45 ` [PATCHv6 20/26] arm: mach-k3: common: Drop main r5 start Tero Kristo
2021-06-11 8:45 ` [PATCHv6 21/26] arm: mach-k3: sysfw-loader: pass boardcfg to sciserver Tero Kristo
2021-06-11 8:45 ` [PATCHv6 22/26] arm: mach-k3: j721e_init: Force early probe of clk-k3 driver Tero Kristo
2021-06-11 8:45 ` [PATCHv6 23/26] configs: j721e_evm_r5: Enable raw access power management features Tero Kristo
2021-06-11 8:45 ` [PATCHv6 24/26] configs: j7200_evm_r5: " Tero Kristo
2021-06-11 8:45 ` [PATCHv6 25/26] board: ti: j72xx: README: update build instructions and image formats Tero Kristo
2021-06-11 8:45 ` [PATCHv6 26/26] arm: dts: k3-j72xx: correct MCU timer1 frequency Tero Kristo
2021-06-11 11:08 ` [PATCHv6 00/26] HSM rearch series for TI K3 devices Lokesh Vutla
2021-06-11 11:18 ` Tero Kristo [this message]
2021-06-11 13:43 ` Lokesh Vutla
2021-06-11 14:13 ` Tom Rini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=22da4ad1-8a11-50fb-7e97-2caa0ee187dc@kernel.org \
--to=kristo@kernel.org \
--cc=lokeshvutla@ti.com \
--cc=trini@konsulko.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox