* [U-Boot] ERROR: too many flash sectors
@ 2009-08-20 14:45 SlinceArm
2009-08-20 14:58 ` Stefan Roese
0 siblings, 1 reply; 6+ messages in thread
From: SlinceArm @ 2009-08-20 14:45 UTC (permalink / raw)
To: u-boot
Hi , everyone .
My u-boot version is 2009-01 and i try porting u-boot on pxa270 development
board.
when i power on my board then minicom show these information
DRAM: 64 MB
ERROR: too many flash sectors
ERROR: too many flash sectors
Flash: 32 MB
then i can save setenv , but when i earse my flash ,it cause one error
Error: end address not on sector boundary
and here is my flinfo :
Bank # 1: CFI conformant FLASH (32 x 16) Size: 32 MB in 128 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x18
Erase timeout: 4096 ms, write timeout: 1 ms
Buffer write timeout: 2 ms, buffer size: 64 bytes
Sector Start Addresses:
00000000 RO 00040000 RO 00080000 RO 000C0000 RO 00100000
RO
etc...
And i dont know my network chip work or not . ( my chip is LAN91C113 )
when i ping some address , it show
ethid=0000...
LAN91C113:PHY auto-negotiate timed out
then my bootloader freeze ....
would someone can help me ? thanks.
--
View this message in context: http://www.nabble.com/-U-Boot--ERROR%3A-too-many-flash-sectors-tp25063511p25063511.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
^ permalink raw reply [flat|nested] 6+ messages in thread
* [U-Boot] ERROR: too many flash sectors
2009-08-20 14:45 [U-Boot] ERROR: too many flash sectors SlinceArm
@ 2009-08-20 14:58 ` Stefan Roese
2009-08-22 2:58 ` SlinceArm
0 siblings, 1 reply; 6+ messages in thread
From: Stefan Roese @ 2009-08-20 14:58 UTC (permalink / raw)
To: u-boot
On Thursday 20 August 2009 16:45:28 SlinceArm wrote:
> Hi , everyone .
>
> My u-boot version is 2009-01 and i try porting u-boot on pxa270 development
> board.
> when i power on my board then minicom show these information
>
> DRAM: 64 MB
> ERROR: too many flash sectors
> ERROR: too many flash sectors
This error is important. Searching in the source code gives you an hint. You
should increase CONFIG_SYS_MAX_FLASH_SECT to match you hardware.
Cheers,
Stefan
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-0 Fax: (+49)-8142-66989-80 Email: office at denx.de
^ permalink raw reply [flat|nested] 6+ messages in thread
* [U-Boot] ERROR: too many flash sectors
2009-08-20 14:58 ` Stefan Roese
@ 2009-08-22 2:58 ` SlinceArm
2009-08-23 16:15 ` Penda, Naveen Kumar
2009-08-24 8:57 ` Stefan Roese
0 siblings, 2 replies; 6+ messages in thread
From: SlinceArm @ 2009-08-22 2:58 UTC (permalink / raw)
To: u-boot
Stefan Roese wrote:
>
>>
>> DRAM: 64 MB
>> ERROR: too many flash sectors
>> ERROR: too many flash sectors
>
>>>This error is important. Searching in the source code gives you an hint.
You
>>>should increase CONFIG_SYS_MAX_FLASH_SECT to match you hardware.
>
>>>Cheers,
>>>Stefan
>
>
Stefan Roese wrote:
>
> On Thursday 20 August 2009 16:45:28 SlinceArm wrote:
>> Hi , everyone .
>>
>> My u-boot version is 2009-01 and i try porting u-boot on pxa270
>> development
>> board.
>> when i power on my board then minicom show these information
>>
>> DRAM: 64 MB
>> ERROR: too many flash sectors
>> ERROR: too many flash sectors
>
> This error is important. Searching in the source code gives you an hint.
> You
> should increase CONFIG_SYS_MAX_FLASH_SECT to match you hardware.
>
> Cheers,
> Stefan
>
Thanks for your reply , Stefan. : )
My flash is 32MB
and here is my source code for flash environment
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER 1
#define CONFIG_FLASH_CFI_WIDTH FLASH_CFI_32BIT
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_MAX_FLASH_SECT 128
What code did set wrong ??
--
View this message in context: http://www.nabble.com/-U-Boot--ERROR%3A-too-many-flash-sectors-tp25063511p25090177.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
^ permalink raw reply [flat|nested] 6+ messages in thread
* [U-Boot] ERROR: too many flash sectors
2009-08-22 2:58 ` SlinceArm
@ 2009-08-23 16:15 ` Penda, Naveen Kumar
2009-08-24 8:57 ` Stefan Roese
1 sibling, 0 replies; 6+ messages in thread
From: Penda, Naveen Kumar @ 2009-08-23 16:15 UTC (permalink / raw)
To: u-boot
>
>
>
> Stefan Roese wrote:
> >
> >>
> >> DRAM: 64 MB
> >> ERROR: too many flash sectors
> >> ERROR: too many flash sectors
> >
> >>>This error is important. Searching in the source code
> gives you an hint.
> You
> >>>should increase CONFIG_SYS_MAX_FLASH_SECT to match you hardware.
> >
> >>>Cheers,
> >>>Stefan
> >
> >
>
>
> Stefan Roese wrote:
> >
> > On Thursday 20 August 2009 16:45:28 SlinceArm wrote:
> >> Hi , everyone .
> >>
> >> My u-boot version is 2009-01 and i try porting u-boot on pxa270
> >> development
> >> board.
> >> when i power on my board then minicom show these information
> >>
> >> DRAM: 64 MB
> >> ERROR: too many flash sectors
> >> ERROR: too many flash sectors
> >
> > This error is important. Searching in the source code gives
> you an hint.
> > You
> > should increase CONFIG_SYS_MAX_FLASH_SECT to match you hardware.
> >
> > Cheers,
> > Stefan
> >
>
> Thanks for your reply , Stefan. : )
>
> My flash is 32MB
>
> and here is my source code for flash environment
>
> #define CONFIG_SYS_FLASH_CFI
> #define CONFIG_FLASH_CFI_DRIVER 1
> #define CONFIG_FLASH_CFI_WIDTH FLASH_CFI_32BIT
>
> #define CONFIG_SYS_MAX_FLASH_BANKS 1
> #define CONFIG_SYS_MAX_FLASH_SECT 128
Please check your sector size CONFIG_SYS_ENV_SECT_SIZE and multiply with your CONFIG_SYS_MAX_FLASH_SECT should not cross 32MB
>
> What code did set wrong ??
> --
> View this message in context:
> http://www.nabble.com/-U-Boot--ERROR%3A-too-many-flash-sectors
> -tp25063511p25090177.html
> Sent from the Uboot - Users mailing list archive at Nabble.com.
>
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
>
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* [U-Boot] ERROR: too many flash sectors
2009-08-22 2:58 ` SlinceArm
2009-08-23 16:15 ` Penda, Naveen Kumar
@ 2009-08-24 8:57 ` Stefan Roese
2009-08-24 14:39 ` SlinceArm
1 sibling, 1 reply; 6+ messages in thread
From: Stefan Roese @ 2009-08-24 8:57 UTC (permalink / raw)
To: u-boot
On Saturday 22 August 2009 04:58:44 SlinceArm wrote:
> Thanks for your reply , Stefan. : )
>
> My flash is 32MB
>
> and here is my source code for flash environment
>
> #define CONFIG_SYS_FLASH_CFI
> #define CONFIG_FLASH_CFI_DRIVER 1
> #define CONFIG_FLASH_CFI_WIDTH FLASH_CFI_32BIT
>
> #define CONFIG_SYS_MAX_FLASH_BANKS 1
> #define CONFIG_SYS_MAX_FLASH_SECT 128
>
> What code did set wrong ??
As I already mentioned, the CONFIG_SYS_MAX_FLASH_SECT value is too low. I
suggest you increase it to 512 and give it another try.
Cheers,
Stefan
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-0 Fax: (+49)-8142-66989-80 Email: office at denx.de
^ permalink raw reply [flat|nested] 6+ messages in thread
* [U-Boot] ERROR: too many flash sectors
2009-08-24 8:57 ` Stefan Roese
@ 2009-08-24 14:39 ` SlinceArm
0 siblings, 0 replies; 6+ messages in thread
From: SlinceArm @ 2009-08-24 14:39 UTC (permalink / raw)
To: u-boot
Stefan Roese wrote:
>
> On Saturday 22 August 2009 04:58:44 SlinceArm wrote:
>> Thanks for your reply , Stefan. : )
>>
>> My flash is 32MB
>>
>> and here is my source code for flash environment
>>
>> #define CONFIG_SYS_FLASH_CFI
>> #define CONFIG_FLASH_CFI_DRIVER 1
>> #define CONFIG_FLASH_CFI_WIDTH FLASH_CFI_32BIT
>>
>> #define CONFIG_SYS_MAX_FLASH_BANKS 1
>> #define CONFIG_SYS_MAX_FLASH_SECT 128
>>
>> What code did set wrong ??
>
> As I already mentioned, the CONFIG_SYS_MAX_FLASH_SECT value is too low. I
> suggest you increase it to 512 and give it another try.
>
> Cheers,
> Stefan
>
> --
> DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: (+49)-8142-66989-0 Fax: (+49)-8142-66989-80 Email: office at denx.de
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
>
>
thaks your reply, Stefan .
i follow your suggestion .
increase the CONFIG_SYS_MAX_FLASH_SECT to 256.
and the Error is fixed . : )
Thanks your suggestion.
--
View this message in context: http://www.nabble.com/-U-Boot--ERROR%3A-too-many-flash-sectors-tp25063511p25117245.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2009-08-24 14:39 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2009-08-20 14:45 [U-Boot] ERROR: too many flash sectors SlinceArm
2009-08-20 14:58 ` Stefan Roese
2009-08-22 2:58 ` SlinceArm
2009-08-23 16:15 ` Penda, Naveen Kumar
2009-08-24 8:57 ` Stefan Roese
2009-08-24 14:39 ` SlinceArm
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox