[U-Boot] [PATCH v3 1/4] usb: rockchip-phy: implement USB2.0 phy control for Synopsys

[Heiko Stuebner <heiko@sntech.de>]

Am Mittwoch, 6. Juli 2016, 14:48:57 schrieb Heiko Stuebner:
> Am Mittwoch, 6. Juli 2016, 18:20:04 schrieb Ziyuan Xu:
> > Hi heiko,
> > 
> > On 2016?07?06? 17:34, Ziyuan Xu wrote:
> > > From: Xu Ziyuan <xzy.xu@rock-chips.com>
> > > 
> > > So far, Rockchip SoCs have two kinds of USB2.0 phy, like Synopsys and
> > > Innosilicon. This patch applys dwc2 usb driver framework to implement
> > > phy_init and phy_off for Synopsys phy on Rockchip platform.
> > > 
> > > Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
> > > 
> > > ---
> > > 
> > > Changes in v3:
> > > - Make UOC_CON registers to be unfixed which should be got from DT
> > > 
> > > Changes in v2:
> > > - Rename rk3288_usb_phy.c to rockchip_usb_syno_phy.c
> > > - Rework the behaviour in otg_phy_init() and otg_phy_off()
> > > 
> > >   drivers/usb/phy/Makefile                |  1 +
> > >   drivers/usb/phy/rockchip_usb_syno_phy.c | 47
> > >   +++++++++++++++++++++++++++++++++ 2 files changed, 48 insertions(+)
> > >   create mode 100644 drivers/usb/phy/rockchip_usb_syno_phy.c
> > > 
> > > diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile
> > > index 93d147e..8002a18 100644
> > > --- a/drivers/usb/phy/Makefile
> > > +++ b/drivers/usb/phy/Makefile
> > > @@ -7,3 +7,4 @@
> > > 
> > >   obj-$(CONFIG_TWL4030_USB) += twl4030.o
> > >   obj-$(CONFIG_OMAP_USB_PHY) += omap_usb_phy.o
> > > 
> > > +obj-$(CONFIG_ROCKCHIP_USB_SYNO_PHY) += rockchip_usb_syno_phy.o
> > > diff --git a/drivers/usb/phy/rockchip_usb_syno_phy.c
> > > b/drivers/usb/phy/rockchip_usb_syno_phy.c new file mode 100644
> > > index 0000000..ab049e1
> > > --- /dev/null
> > > +++ b/drivers/usb/phy/rockchip_usb_syno_phy.c
> > > @@ -0,0 +1,47 @@
> > > +/*
> > > + * Copyright 2016 Rockchip Electronics Co., Ltd
> > > + *
> > > + * SPDX-License-Identifier:    GPL-2.0+
> > > + */
> > > +
> > > +#include <common.h>
> > > +#include <asm/io.h>
> > > +
> > > +#include "../gadget/dwc2_udc_otg_priv.h"
> > > +
> > > +#define UOC_CON(x)		((x) * 0x4)
> > 
> > As you know, dwc2 usb driver didn't apply devicetree model. It's hard to
> > implement a compatible driver for Rockchip SoCs which use a same udc.
> 
> Yeah, it is pretty strange that the dwc2 host part in uboot uses the
> devicetree while the gadget part does not - but I maybe someone else can
> answer this, as my contact with uboot was limited until now.
> The dwc2 host driver works just fine on my rk3036 kylin board.
> 
> > For example,
> > SOFT_CTRL bit is  UOC_CON2[2] on RK3288
> > I can't assure it's also UOC_CON[2] on other socs.
> > Do you have any good ideas?
> 
> Operating under the current constraints, I guess you could simply do
> something similar to what socfpga does in its board file.
> 
> Aka get the usb controller node, read the phy phandle and get the phy
> compatible string from the dts. The usbphys each have per-soc compatible
> values "rockchip,rk3288-usbphy" etc, so you can determine the needed bits
> over that.

forgot to add, with this same mechanism you could also resolve the fifo 
length from the devicetree into the platdata struct instead of hard-coding 
it with an ARCH_ROCKCHIP define.


Heiko